Advertisement
Quick Links
BATTERY RACK ISLANDER ASSEMBLY
STARTER KIT
LAD DESCRIPTION:
BATTERY ISLANDER ASSEMBLY INSTRUCTIONS
LAD PART #:
301350IS
Walmart Part #:
100569607, 100569605, 100569606, 100569608
Walmart Description:
BATTERY ISLANDER AND ADD-ON
ADD-ON KIT
Scan the QR code or visit
www.ladarling.com/battery-rack/
for the latest copy of the instruction sheets.
BY
DATE
REV.
Customer Service 1-800-682-5730
1
RM
6/29/2024
PAGE
1 OF 14
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for LA Darling 100569607
Summary of Contents for LA Darling 100569607
- Page 1 Walmart Part #: BATTERY RACK ISLANDER ASSEMBLY 100569607, 100569605, 100569606, 100569608 Walmart Description: BATTERY ISLANDER AND ADD-ON ADD-ON KIT STARTER KIT Scan the QR code or visit www.ladarling.com/battery-rack/ LAD DESCRIPTION: for the latest copy of the instruction sheets. BATTERY ISLANDER ASSEMBLY INSTRUCTIONS...
- Page 2 Walmart Part #: 100569605 AND 100569607 BATTERY RACK ISLANDER STARTER - END CAP Walmart Description: STARTER UNIT ONLY END CAP FRAMES SHOULD BE ANCHORED TO THE FLOOR. INSTALLED THROUGH THE HOLES PROVIDED IN THE FRAME (SEE NOTE) FOOT PLATES. ANCHOR BOLTS SHOULD BE FULLY SEATED DOWN TO FOOT PLATES.
- Page 3 STEP 1: SET UPRIGHTS AND BEAMS ONLY END CAP FRAMES SHOULD BE ANCHORED TO THE FLOOR USING THE SUPPLIED (4) 537883212 (ANCHOR BOLT) IN FRONT (USE BEAMS WITH TAG MOLDING) SET FIRST BEAM INTO SLOTS CLOSEST TO THE FLOOR, AND ATTACH BY INSERTING ONE LEG OF A RETAINER PIN THROUGH THE BEAM BRACKET AND UPRIGHT.
- Page 4 STEP 2: INSTALL DECK SUPPORTS INSTALL 14" DECK SUPPORTS IN 14" WIDESPAN FRAMES AND 32" DECK SUPPORTS IN 32" WIDESPAN FRAMES. HOLDING THE DECK SUPPORT AT AN ANGLE TO THE BEAM, SQUEEZE THE OPEN SIDE AND INSERT INTO THE BEAM, THEN SWING THE FREE END AROUND TO THE OPPOSITE BEAM, SQUEEZE THE OPEN SIDE AND INSERT INTO THE BEAM.
- Page 5 STEP 3: INSTALL WIRE DECKS STARTING WITH THE LOWEST DECK FIRST, LAY WIRE DECKS INTO POSITION FROM THE FRONT. MAKE SURE WIRE DECKS ARE SITTING DOWN INSIDE OF THE BEAMS AND CENTERED BETWEEN THE FRAMES WITH THE SINGLE WIRE RETAINER FORWARD. TWO PEOPLE ARE RECOMMENDED FOR INSTALLING THE 32"...
- Page 6 STEP 4: INSTALL DIVIDERS LAY DIVIDER OVER DESIRED VERTICAL WIRE. SLIDE DIVIDER FORWARD ENGAGING THE HOOKS UNDER THE HORIZONTAL WIRES AS SHOWN. PLACE 4 DIVIDERS PER SHELF, ROUGHLY 9" APART OR AS NEEDED PER PLANOGRAM. NOTE: DOUBLE WIRE ON GRID DECKS ARE MEANT AS A LOADING AID.
- Page 7 STEP 5: INSTALL WING PANELS AND SIGN PANEL RAISE WING PANEL OVER THE HORIZONTAL BRACE FOR THE UPRIGHTS ON THE END CAP. MAKE SURE WING PANEL BRACKET IS ABOVE THE BRACE. SNAP TOP BRACKET FROM THE WING PANEL OVER THE HORIZONTAL BRACE AT THE TOP WHILE ALSO HOOKING TOP WING PANEL BRACKET THE BOTTOM BRACKET OVER THE LOWER HORIZONTAL...
- Page 8 GRAVITY FEED INSTALLATION STEP 1: SET UPRIGHTS AND BEAMS IN FRONT (USE BEAMS WITH TAG MOLDING) 1. FOLLOW STEPS 1-3 ON SHEET 3. STEP 2: INSTALL WIRE RACKS INSTALL REAR WIRE SHELF ON TOP OF REAR BEAM. INSTALL FRONT WIRE SHELF INSIDE ON BACK OF FRONT BEAM. REPEAT UNTILL ALL WIRE SHELVES ARE INSTALLED.
- Page 9 SWING OUT INSTALLATION STEP 1: ASSEMBLE SWING OUT SECTION IN FRONT (USE BEAMS WITH TAG MOLDING) 1. ASSEMBLE BEAMS AS SHOWN BELOW REAR BEAM IN BACK (USE BEAMS WITHOUT TAG MOLDING) 1. SET REAR BEAMS AT THE SAME HEIGHT AS FRONT BEAMS. ONCE ALL BEAMS ARE SET 1.
- Page 10 Walmart Part #: 100569605 AND 100569607 BATTERY RACK ISLANDER STARTER Walmart Description: STARTER UNIT LAD DESCRIPTION: BATTERY ISLANDER ASSEMBLY INSTRUCTIONS DATE PAGE LAD PART #: REV. Customer Service 1-800-682-5730 6/29/2024 10 OF 14 301350IS...
-
Page 11: Starter Assembly
STARTER ASSEMBLY SECURE SWING OUT FRAME TO PIVOT FRAME USING HINGE PINS AS SHOWN (2 PER SWING OUT FRAME) SECURE SWING OUT FRAME, WHEN CLOSED, BY ENGAGING LOCKING PIN AS SHOWN. (1 PER SWING OUT FRAME HING PIN DETAIL N LOCKING PIN HINGE PIN DETAIL R... - Page 12 Walmart Part #: 100569606 & 100569608 BATTERY RACK ISLANDER ADD-ON Walmart Description: ADD-ON UNIT LAD DESCRIPTION: BATTERY ISLANDER ASSEMBLY INSTRUCTIONS DATE PAGE LAD PART #: REV. Customer Service 1-800-682-5730 6/29/2024 12 OF 14 301350IS...
- Page 13 STEP 1: SET UPRIGHTS AND BEAMS ONLY END CAP FRAMES SHOULD BE ANCHORED TO THE FLOOR USING THE SUPPLIED (4) 537883212 (ANCHOR BOLT) IN FRONT (USE BEAMS WITH TAG MOLDING) SET FIRST BEAM INTO SLOTS CLOSEST TO THE FLOOR, AND ATTACH BY INSERTING ONE LEG OF A RETAINER PIN THROUGH THE BEAM BRACKET AND UPRIGHT.
- Page 14 STEP 2: ATTACH SWING OUT SECTION TO FRAME SECTION SIGN PANEL 1. PIN SWING OUT SECTION TO THE FRAME SECTION SHOWN BELOW. 2. PLACE SIGN PANELS TO TOP OF SWING OUT SECTION AND SIGN PANEL FRAME SECTION. PREP FOR CONNECTING TO STARTER KIT 1.
Need help?
Do you have a question about the 100569607 and is the answer not in the manual?
Questions and answers