Related Manuals for Angry Audio RAVE!
Summary of Contents for Angry Audio RAVE!
- Page 1 RAVE! RADIO MIXING CONSOLE USER MANUAL © 2024 ANGRY AUDIO LLC RAVE! Radio mixing console. Power supply (shown with optional rack mount kit). RAVE! User Manual Page...
-
Page 2: Table Of Contents
$2,000 price point. I think we nailed it! Did you know that all Angry Audio products are backed by a 30-day "love it or return it" guarantee? This is an industry first. Yes, this promise extends even to our consoles. If you don’t absolutely love it, you can send it back— no restocking fees, no lengthy forms, no hassles. -
Page 3: Safety & Compliance
Safety & Compliance Safety Guidelines We know you’re itching to dive in. But please slow down long enough to read and understand this section fully before installing or using the product. Your safety is important to us! ⚠ This product contains potentially-lethal voltages. Do not open unless you are qualified to do so. ⚠... -
Page 4: Installation & Configuration
Find a suitable location for your power supply. Ensure adequate ventilation around the supply. If you have space available in an equipment rack, you will want to order the optional Angry Audio rack mount kit (P/N 992001) from your favorite reseller. It makes for a very clean and professional installation. -
Page 5: Audio Wiring
Audio Wiring All of the line inputs and outputs are on RJ45 connectors using the StudioHub+ pinout. StudioHub uses shielded CAT-5 cables to transport analog and digital audio. Adapters are available to interface to a wide variety of common audio connector types. StudioHub to XLR adapter. -
Page 6: Control Wiring
RAVE! is engineered for professional broadcast. All of the inputs and outputs are fully balanced. Line inputs and outputs operate at a nominal +4dBu. There is a special feature on channels 5 and 6 that allows for unbalanced sources. You’ll use a StudioHub to RCA adapter and flip a switch to boost the lower -10dBV level of unbalanced consumer-type (IHF) source equipment. -
Page 7: Connections
Connections Microphone/Line Inputs (Channels 01-04) Each of channels 01, 02, 03 and 04 can be either microphone or stereo line source. A recessed switch for each input allows you to choose between the XLR and the RJ45 input. LINE IN 07 LINE IN 05 MIC IN 04 LINE IN 03... -
Page 8: Microphone Calibration
MIX MINUS 08 RAVE! has a built-in +48VDC phantom power supply for condenser microphones. If any of your microphones require phantom power, flip the recessed P48 switch to the down position. The red LED on the rear panel will illuminate. Phantom voltage will be applied to all of the XLR connectors. -
Page 9: External Line Input
External Line Input There is one additional line input connection: the External source for the monitors. This may be audio from a radio tuner or from some other source you may want to be able to monitor, but is not going to be a source for your show. Feed stereo +4dBu into this input. -
Page 10: Mix-Minus Outputs
Skype call or Zoom session will hear the mix perfectly, but not themselves. A smartphone could even get into the act using the Angry Audio Bluetooth Gadget. Connect the analog outputs of the GADGET to the input of either channel 07 or 08. Connect the Gadget mix-minus input to mix-minus output 07 or 08. -
Page 11: Monitor Outputs
+4dBu nominal level signal. In addition to the audio signal, the Guest Output also provides ±15VDC using the StudioHub+ format. This makes it very convenient to drive one or more Angry Audio Headphone Gizmos with audio and power on a shielded CAT-5 cable. -
Page 12: Logic Connections
CONNECTOR SIGNAL LEVEL PREVIEW OUT Preview Left Output Hot +4dBu Nominal, Variable PREVIEW OUT Preview Left Output Cold +4dBu Nominal, Variable PREVIEW OUT Preview Right Output Hot +4dBu Nominal, Variable PREVIEW OUT Preview Right Output Cold +4dBu Nominal, Variable CR MON OUT CR Monitor Left Output Hot +4dBu Nominal, Variable CR MON OUT... - Page 13 duration of the press. This mimics exactly the button on the console. A tally output illuminates an LED when the channel is On and unmuted. Use the shell of the RJ45 to provide ground for the external logic. CONNECTOR SIGNAL LEVEL MIC 1-4 Ch01 Remote Switch...
-
Page 14: Logic Examples
Remote Mic Control Button example. The Angry Audio 3-segment Signal Light can be plugged into the OnAir/User connector using a CAT-5 patch cable. The red segment will illuminate when any mics are active. The yellow and green segments will follow the yellow and green user buttons. -
Page 15: Operation
Operation Fader Channels for Mic Sources Fader channels 01 through 04 will have been configured during installation for either microphone or line functionality. This page will describe the channel strip functions when the channel has been configured for PROGRAM PROGRAM microphone. -
Page 16: Line Fader Channels
Fader Channels for Line Sources Fader channels 05 through 08 are line sources. This page describes the PROGRAM PROGRAM function of these fader channels. It also describes any of channels 01 through 04 that have been configured for line sources. Program and Audition switches send the output of this channel to either or AUDITION AUDITION... -
Page 17: Mix-Minus Outputs And User Buttons
The user buttons are toggle function. Push once to activate and again to de-activate. If you have one of the Angry Audio 3-segment Signal Lights, these will TALK control the yellow and green segments while the OnAir status of RAVE! will control the red segment. -
Page 18: Monitors (Board Operator)
PROGRAM AUDITION AUDITION ON AIR RIGHT RIGHT LEFT RIGHT LEFT Monitors (Board Operator) Select what you want to hear in the control room monitors by pressing one PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM of the three buttons at the top. -
Page 19: Headphones (Board Operator)
AUDITION AUDITION ON AIR RIGHT LEFT RIGHT LEFT RIGHT Headphones (Board Operator) Plug your headphones into either of the two jacks on the right side of PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM PROGRAM RAVE! The jacks are mutually exclusive, you cannot use both at the same time. -
Page 20: Studio Guests
PREVIEW PREVIEW controls so each guest can set volume to taste. If you use the Angry Audio Headphone Gizmo, a few shielded CAT-5 cables TALK are all you need to provide both power and audio to up to three units. -
Page 21: Meters
Meters RAVE! provides four precision LED meters for keeping track of levels. The leftmost pair are for Program Left and Right. Notice the outline around the 0 mark. This is your target mix level. If your mix is usually below this target, raise PROGRAM AUDITION ON AIR... -
Page 22: Specifications
Specifications Part Numbers: North America 994001 Australia 994001A Europe 994001E United Kingdom 994001U Power & Environmental: Power Input 115 VAC 50/60Hz (North America Version) Power Input 230 VAC 50/60Hz (Australia, Europe, UK Versions) Power Consumption 50 VA Operating Temperature 0° to 40° C (32° to 104° F) Storage Temperature -20°... - Page 23 Dimensional Drawing RAVE! User Manual Page...
-
Page 24: Warranty & Support
This product carries a manufacturer’s warranty which is subject to the following guidelines and limitations: A. Except as expressly excluded hereinafter, Angry Audio LLC (“Seller”) warrants equipment of its own manufacture against faulty workmanship or the use of defective materials for a period of two (2) years from date of shipment to Buyer.
Need help?
Do you have a question about the RAVE! and is the answer not in the manual?
Questions and answers