Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Yota EVC-1
- Page 1 Installation / User manual EVC-1 & EVC-1-WF (Commercial EV-charger)
-
Page 2: Important Safety Instructions
AVERTISSEMENT! Ce manuel contient des instructions importantes pour les modèles : 1. Important Safety Instructions Série EVC-1 qui doit être suivie pendant l'installation, le fonctionnement et la maintenance de l'unité. W ARNING! This manual contains important instructions. Read first and verify installation. -
Page 3: Basic Interface
USER MANUAL USER MANUAL 2. Basic Interface WARNING This product complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and this device might accept any interference LED Light received, including interference that may cause undesired operation. -
Page 4: Product Dimensions
USER MANUAL USER MANUAL 3. Product Dimensions 4. Design and Manufacturing Standards UL 2594: Electric Vehicle Supply Equipment 9.8″ UL 2231-1: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: General 3.9″ Requirements UL 2231-2: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: Particular Requirements for Protection Devices for Use in Charging Systems UL 2251: Plugs, Receptacles and Couplers for Electric Vehicles UL 62: Flexible Cords and Cables... -
Page 5: Specification
USER MANUAL USER MANUAL 5. Specification 6. Status Description of the Charger Indication Light Model Name EVC-1 & EVC-1-WF Rated Input Voltage 200-240V (AC) Single Phase READY Standby - Blue Light Rated Output Current 48A MAX (Adjustable 16/32/40A) / 16A Default... -
Page 6: Packing List
• Be sure to read the user manual and ensure local building and electrical codes are reviewed before installing the AC charger. • The EVC-1 charger should be installed by a qualified technician according to the user manual and local safety regulations. - Page 7 USER MANUAL USER MANUAL 8.2 Wiring For safety regulations, please add circuit breaker protection in the input part of charging pile. Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2, GROUNDING INSTRUCTIONS connect the PE lead to the grid PE. This product must be grounded.
-
Page 8: Tools And Materials Required
USER MANUAL USER MANUAL 8.3 Tools and Materials Required 8.4 Wall-Mounted Bracket Installation Step 1: Tools required before installing the Wall-Mounted charger: • Set the position of the screw holes (4) and drill them with a 5/16” (8mm) drill bit and •... - Page 9 9.2.1 Operating Steps with Plug and Charge Step 1 / Standby Mode Once installed, the EVC-1 should look like the images below: After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) should all lit. Standby mode should be ready when the blue light (READY) is steady on.
- Page 10 USER MANUAL USER MANUAL 9.2.2 Operating Steps with RFID card Step 1 / Standby Mode After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) should all lit. Standby mode should be ready when the blue light (READY) is steady on. CHARGE READY Step 4 / Charging Finished...
-
Page 11: Error And Warning Message
USER MANUAL USER MANUAL 9.3 Error and Warning Message Status Remark Input OVP 1 flashes followed by 3 sec pause Auto Recover Input UVP 2 flashes followed by 3 sec pause Auto Recover Output OCP 3 flashes followed by 3 sec pause Auto Recover 4 flashes followed by 3 sec pause Auto Recover... -
Page 12: Maintenance Spare Parts
USER MANUAL USER MANUAL • During the warranty period, any malfunction caused within normal using conditions according 10. Maintenance and Repair to the User Manual, the product shall be replaced or repaired (free of charge), except on the 10.1 Daily Maintenance following conditions: Please keep the charger clean and in a clean area with low humidity.
Need help?
Do you have a question about the EVC-1 and is the answer not in the manual?
Questions and answers