SnS Grills SNS-500 Instruction Manual

SNS-500 INSTRUCTION MANUAL
EXTENDED RANGE WIRELESS FOOD THERMOMETER
Congratulations on your purchase of the SNS-500,
now remotely monitor the temperature of grilling food
1. 1- Receiver unit - smaller unit
2. 1- Transmitter unit - larger unit
3. 1- 2 detachable stainless steel 6" long waterproof food probes
4. 1- 2 detachable stainless steel 3" long waterproof bbq probes with clips
5. 4- AAA batteries
RECEIVER FEATURES
LCD
•
LCD (Liquid Crystal Display) - Displays all icons, temperature for all 4 probes
• BATTERY COMPARTMENT - Holds 2 AAA batteries
•
STAND/HANGER - Swings out and allows you to hang the unit or stand the receiver on a tabletop
•
MAGNETS – Allows you to affix to most metallic surfaces
RECEIVER BUTTONS
1. °C/°F - Press to switch display between Fahrenheit or Celsius.
2. - A quick press tums the unit on. Press and hold for 2 seconds to turn the receiver off.
3. LIGHT ON/OFF – A quick press turns the LED flashlight on or off.
4. SYNC / VOL –With both units in close proximity to each other, press and hold both this button and the SYNC /
VOL button on the transmitter unit for 2 seconds to sync the units. Once the units have connected you will see
this symbol . A short press of this button will allow you to adjust the volume of the unit from its low to high
setting and vice versa.
Pressing any button turns on the LCD backlight for approximately 10 seconds.
INTRODUCTION
a programmable radio frequency food thermometer. You
and the temperature inside your grill from up to 500
COMPONENTS
Magnets
Stand /
Hanger
can
ft away.
LCD
•
LCD (Liquid Crystal Display) - Displays all icons, temperature for all 4 probes
SYNC/
•
BATTERY COMPARTMENT - Holds 2 AAA batteries
VOL
•
STAND/HANGER -
•
MAGNETS - Allows you to affix to most metallic surfaces
Temperature range of probe: 14 °F to 572°F (-10°C to 300°C)
1. Probe Buttons 1,2,3,4 – A quick press of any button sets the High and Low Alarm temperatures. A long press (2
seconds) in Alarm mode turns off the Alarm for that probe. (Example: long press button 1 turns off alarm for probe
1).
2. (Down) / (Up) - Press to lower or raise the Alarm temperatures. See below for adjusting volume.
3. ALARM ON/OFF - Press to activate or deactivate the Alarm mode for all probes.
4. ALARM SET - Press to lock in High/Low Alarm temperature.
Battery
5. °C/°F - Press to switch display between Fahrenheit or Celsius.
Compartment
6. - A quick press tums the unit on. Press and hold for 2 seconds to turn the transmitter off.
7. SYNC / VOL – With both units in close proximity to each other, press and hold both this button and the SYNC /
VOL button on the receiver unit for 2 seconds to sync the units. Once the units have connected you will see this
symbol . A short press of this button will allow you to adjust the volume of the unit from its low to high setting
and vice versa.
Pressing any button turns on the LCD backlight for approximately 10 seconds.
Open the battery compartment of
"AAA" batteries with correct polarity. Align the battery door and snap the latch back in place.
With both units on, sync the receiver with the transmitter by pressing and holding down the VOL/SYNC buttons for 2
seconds on both the transmitter and receiver. It does not matter what order.
The receiver will begin silently
continue flashing silently
the receiver time to re-sync before notifying
to the receiver's range limit. After 3 minutes, an audible alarm will sound on the receiver for 60 seconds to alert
you that they will need to be re-synced.
TRANSMITTER FEATURES
Magnets
Stand/
Hanger
Swings out and allows you to hang the unit or stand the transmitter on a tabletop
TRANSMITTER BUTTONS
INSTALLING BATTERIES
the receiver and transmitter by pressing down the battery door latch. Insert two
EZ-SYNC TECHNOLOGY
SYNC LOSS ALARM
flashing after loss of the synced connection for
for 3 minutes. In this time the units will attempt to re-sync with one another. This
you, which makes the receiver more convenient to use when close
SYNC /
VOL
Battery
Compartment
60 seconds. The receiver will
gives