Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Tucker Barbecues ARCHITECTURAL Series
- Page 1 ARCHITECTURAL SERIES RADIANT ELECTRIC HEATERS PRODUCT MANUAL FOR MODELS: A2000, A3000, A4000, AD4000, AD6000. HEATERS MADE FOR COASTAL CONDITIONS. 316 MARINE GRADE STAINLESS STEEL CONSTRUCTION. HIGH EFFICIENCY RADIANT INFRARED QUARTZ ELEMENTS. DESIGNED FOR INDOOR AND OUTDOOR UNDERCOVER USE.
-
Page 2: Table Of Contents
CONTENTS IMPORTANT Read all instructions before assembly, installation and usage of this Heater. Keep this manual for future reference. V09.05.2024 IMPORTANT SAFETY INSTRUCTIONS HEATER SPECIFICATIONS AND CLEARANCES - HEATER SPECIFICATIONS - HEATER CLEARANCES TO COMBUSTIBLE MATERIALS HEATER INSTRUCTIONS AND ASSEMBLY - HEATER WIRING AND ELEMENT INSTALLATION - ELECTRIC HEATER POWER WIRING LOCATION, MOUNTING AND MAINTENANCE... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS • Do not use the heater if the heating element is damaged. WARNING FOR YOUR SAFETY HAZARDOUS FIRE OR ELECTRIC SHOCK MAY RESULT IF INSTRUCTIONS ARE IGNORED. Read all instructions before assembly, installation and usage of this Heater. CAUTION: ELECTRICAL WARNING SOURCE OF POSSIBLE IGNITION •... -
Page 4: Heater Specifications And Clearances
(Supplied With Heater) Phillips Head Screwdriver The following information is supplied to assist you with the assembly and installation of your heater. HEATER SPECIFICATIONS Technical Specifications for Alfresco Spaces, Architectural Series Electric Radiant Heaters. Model DIMENSIONS (mm) POWER (WATTS) CURRENT (AMPS) -
Page 5: Heater Clearances To Combustible Materials
HEATER SPECIFICATIONS AND CLEARANCES HEATER CLEARANCES TO Wall Mounted COMBUSTIBLE MATERIALS All clearances shown on the diagrams are all the minimum required. The minimum clearances from the heater to combustible materials must always be maintained, we recommend the use of a spirit level and tape measure when installing the heater. - Page 6 HEATER SPECIFICATIONS AND CLEARANCES Ceiling Mounted All clearances shown on the diagrams are all the minimum required. 80mm 80mm 80mm 80mm MIN. MIN. MIN. MIN. 500mm 500mm 300mm 300mm MIN. MIN. MIN. MIN. 1800mm 1800mm Minimum clearance to floor FLOOR 80mm 80mm MIN.
-
Page 7: Heater Instructions And Assembly
HEATER INSTRUCTIONS AND ASSEMBLY HEATER WIRING AND ELEMENT INSTALLATION CAUTION: ELECTRICAL WARNING ONLY QUALIFIED ELECTRICAL PERSONNEL MUST INSTALL 2. Remove the safety grill from the heater by HEATERS. pulling out the spokes from underneath the lip on one of the long sides of the heater first and then removing the spokes from the other side next, then gently lift the grill up from its center •... - Page 8 HEATER INSTRUCTIONS AND ASSEMBLY 3. Next, remove the 2 x end panels from inside 4. Now, carefully pick up the glass element and the heater using the allen key supplied to remove 1 x press nut and washer from each remove the 2 x bolts at each end holding end and then slide one end panel over each them in place.
- Page 9 HEATER INSTRUCTIONS AND ASSEMBLY 6. Re-fit both end panels back into the heater in their correct locations and secure them in place using the 2 x bolts you removed earlier. Be careful when refitting the end panels back into the heater, even the smallest amount of pressure applied against the glass element can cause the glass to break.
- Page 10 HEATER INSTRUCTIONS AND ASSEMBLY Do not try to turn the fixed press nut, only turn the outside nut. Failure to do this correctly may result in the premature failure of the element and the warranty being void. The AD Model heaters require two elements to be installed inside them, their heater bodies have provision for 2 x elements to locate inside them along with,...
- Page 11 HEATER INSTRUCTIONS AND ASSEMBLY 9. Now attach the power supply cable and conduit to the heater by threading them through the nylon gland attached to the back of the heater and then tighten the top screw on the nylon gland to secure the cabling. Always check to ensure that the rubber sealing pad is correctly positioned around the nylon gland before tightening.
-
Page 12: Electric Heater Power Wiring
HEATER INSTRUCTIONS AND ASSEMBLY ELECTRIC HEATER POWER WIRING Typical 240 volt wiring for single Typical 240 volt wiring for double Pole switch. Pole switch. Heater Heater Wiring for optional 240 volt Dimmer Controller. “Top” marked on rear of control must be installed in “up”... -
Page 13: Location, Mounting And Maintenance
The size of the Architectural Series heaters only heater’s weight. changes in length, they are all made the same width and height. -
Page 14: Flush Mounting Of The Heater Into A Ceiling Cavity
LOCATION, MOUNTING AND MAINTENANCE These features enable the installer flexibility with The mounting brackets are supplied with 8 x phillips the positioning of the heater on site. head bolts and 2 x nuts for the attachment of the brackets to the heater. When installing the heater to a wall or ceiling 4 x bolts are used to attach the 2 x U shaped mounts using the adjustable mounting brackets supplied,... - Page 15 LOCATION, MOUNTING AND MAINTENANCE INCORRECT INSTALLATION CORRECT INSTALLATION This heater must not be installed The heater can not be installed in front of an electrical socket or with any electrical sockets or below an electrical socket. power cables behind it. The heater must be installed For installations under inclined horizontally, failing to do so will...
-
Page 16: Maintenance
LOCATION, MOUNTING AND MAINTENANCE MAINTENANCE CAUTION: ELECTRICAL WARNING Always isolate the power supply to the heater before performing any maintenance or servicing of the heater. To clean the reflector firstly isolate the power supply. Remove the grill and wipe the reflector clean using glass cleaner or warm soapy water and a soft cloth. -
Page 17: Warranty
WARRANTY ARCHITECTURAL SERIES HEATER WARRANTY Unauthorized repairs during the warranty • period. WARRANTY PERIOD WARRANTY AND SERVICE CALL CLAIMS THAT ARE FOUND TO BE FALSE OR NOT WARRANTABLE WILL BE CHARGED OUT. HEATER BODY 5 years QUARTZ ELEMENT 1 years... - Page 18 ALFRESCO SPACES AUSTRALIA PTY LTD DISTRIBUTOR - TUCKER AUSTRALIA PTY LTD. 138 Silverwater Road Suite 6609/32 Wellington Street, Silverwater NSW 2128 AUSTRALIA. Bondi, NSW, 2026 AUSTRALIA. PHONE: (+612) 9748 8368 PHONE: 1800 076 071 FAX: (+612) 9748 8138 (+61) 0420 212 345 EMAIL: mail@tuckerbbq.com.au EMAIL: info@alfrescospaces.com WEB SITE: www.tuckerbbq.com.au...
Need help?
Do you have a question about the ARCHITECTURAL Series and is the answer not in the manual?
Questions and answers