Table of Contents
Advertisement
Quick Links
Sectional and Tilting Door Opener
Installation Instructions and User Guide
PGD600/ PGD800 / PGD1000/PGD1200
WARNING
Please read the manual carefully before installation and use. The installation of your
new door opener must be carried out by a technically qualified or licensed person.
Attempting to install or repair the door opener without suitable technical qualification
may result in severe personal injury, death and / or property damage.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Jaytech PGD600
Summary of Contents for Jaytech PGD600
- Page 1 Sectional and Tilting Door Opener Installation Instructions and User Guide PGD600/ PGD800 / PGD1000/PGD1200 WARNING Please read the manual carefully before installation and use. The installation of your new door opener must be carried out by a technically qualified or licensed person.
-
Page 2: Table Of Contents
CONTENTS Important safety recommendations·····························································- 1 - Basic function introduction········································································- 3 - Special function introduction····································································· - 4 - Installation recommendations····································································- 4 - Installation···························································································· - 5 - Installation (steel track)············································································ - 6 - Installation (aluminum track)····································································· - 7 - Battery backup Assembly (optional)···························································· - 8 - Basic function setting and applying·····························································- 8 - Special function, optional parts introduction and application···························... -
Page 3: Important Safety Recommendations
Important safety recommendations FAILURE COMPLY WITH FOLLOWING SAFETY RECOMMENDATIONS MAY RESULT IN SERIOUS PERSONAL INJURY, DEATH AND / OR PROPERTY DAMAGE. 1. PLEASE READ CAREFULLY AND ADHERE TO ALL SAFETY AND INSTALLATION RECOMMENDATIONS. 2. The opener is designed and manufactured to meet local regulations. The installer must be familiar with local regulations required in respect of the installation of the opener. - Page 4 persons with reduced physical,sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
-
Page 5: Basic Function Introduction
This information shall describe how to use the handling means, such as hooks and ropes; 32. The drive must not be used with a door incorporating a wicket door (unless the drive cannot be operated with the wicket door put in the safe position); 33. -
Page 6: Special Function Introduction
Special function introduction The following functions are made to order in accordance with the special needs of customers: 1. External Fuse 2. Burglar alarm 3. Flash light 4. Pass door protection Installation recommendations there are specific standards that have to be strictly followed regarding the safety rules of electrical Remember installations and automatic gates and doors. -
Page 7: Installation
Installation 1) Read the instruction carefully. 2) Make sure the door structure is solid and suitable to be motor driven. 3) Make sure when the door is moving, there are no friction point. 4) The door must be properly balanced and must be easily lowered and raised by hand. Referring to Fig. -
Page 8: Installation (Steel Track)
Installation (steel track) Fig. 5 1. Fixing the wall bracket(B) to the wall 2cm-15cm over the shaft or intermediate bracket ,and should be center horizontally. (depending on the actual installation space). 2. Fixing the steel track to the wall bracket using axis pin Φ8x90 (C) and cotter pin. (Fig. 5) 3. -
Page 9: Installation (Aluminum Track)
Installation (aluminum track) Fig.6 Fixing the wall bracket(A) to the wall 2cm-15cm over the shaft or intermediate bracket , and should be center horizontally. (depending on the actual installation space). 2. Fixing the steel track to the wall bracket using axis pin Φ8x90 (B) and cotter pin. (Fig. 6) Fixing garage door opener to the track by U bracket(D). -
Page 10: Battery Backup Assembly (Optional)
Battery backup Assembly (optional) Assemble the battery using battery bracket, washers and nuts supplied (Fig. 9, Fig.10). Fig.9 Fig.10 Basic function setting and applying 1. Matching the receiver and transmitter Coding Transmitters: Press and hold on “Code” button for 1 second until the led dot is on (Fig A). - Page 11 Press and hold on “SET” button for 3 seconds until the LED flashes “1”. Press “SET” button again for 1 second . “1” should now display as steady (not flashing). Then adjust the up limit by pressing “UP” button. Fine-tuning “UP” or “DOWN” button to determine the final up limit position (the LED flashes “n”...
- Page 12 5. Auto-close setting Press and hold on “SET” button for 3 seconds until the LED flashes “1”. Press “UP” or “DOWN” to increase or decrease, adjust the LED to flash ”4”, then press “SET” button to enter into auto-close setting, the LED displays the current setting.
-
Page 13: Special Function, Optional Parts Introduction And Application
8. Open/Stop/Close Terminal Connecting a touch off switch to this terminal (Fig.11), you can use the switch when maintaining or the transmitter is left in garage. Special function, optional parts introduction and application 1. External Fuse (optional) Protect the overload of the opener. 2. - Page 14 Fig. 13 Fig. 14 - 12 -...
-
Page 15: Manual Disengagement
Manual disengagement The opener is equipped with a manual release cord to disengage shuttle and move door by hand while holding the handle down (Fig 15). Pull on the handle to disengage the shuttle. To re-engage the door simply run opener in automatic mode or move door by hand until the trolley engages in the chain shuttle. -
Page 16: Important Information For The User
Important information for the user Once the opener has been installed, the user must be informed about how it works and all the risks that can arise if it is used improperly. The user must avoid placing himself/herself in dangerous situations such as standing within the door’s operating range when it is moving. -
Page 17: Technical Specifications
Technical Specifications Model PGD600 PGD800 PGD1000 PGD1200N Rated door area ≤9.0 sqm ≤12.0 sqm ≤15.0 sqm ≤18.0 sqm Rated lifting force ≤60 kgs ≤80 kgs ≤100 kgs ≤120 kgs Rail Steel / Aluminum Steel / Aluminum Steel / Aluminum Steel / Aluminum... -
Page 18: Common Fault & Solutions
Common Fault & Solutions Fault Fault cause Solutions appearance Opener without any 1. Power supply 1. Check the power supply to openers. action 2. Plug wire are loosing 2. Carefully open the motor cover, check all plug wire on control boards. Opener doesn’t work, Faulty learning of “UP”... - Page 19 SAMT LIMITED WARRANTY SAMT Roller Glider RGD350/400/450 SAMT Panel Glider PGD1000/SGD1100LG SAMT is committed to manufacturing and supplying high quality goods. As part of this commitment, we seek to provide reliable service and support for our goods and are pleased to provide you, the original purchaser, with this SAMT Limited Warranty. The benefits given to you under this SAMT Limited Warranty are in addition to any rights and remedies that you may have under Australian consumer protection laws.
- Page 20 Exclusions This warranty does not cover any failure of the Unit due to: Non-compliance with the instructions regarding installation, operation, maintenance and testing of the Unit or of any product with which the Unit is used. Any attempt to repair, dismantle, reinstall or move the Product to another location once the Product is installed by any person other than an authorised installer.
Need help?
Do you have a question about the PGD600 and is the answer not in the manual?
Questions and answers