Subscribe to Our Youtube Channel
Summary of Contents for Microtronics PSU413D+ AP
-
Page 1: Cover
User manual PSU Charger Cover Valid from: Firmware version: 01v008 App. version: 01v000 Server version: --- Hardware version: 1.2 301624 | Rev.01... -
Page 3: Table Of Contents
Chapter 1 Table of contents Chapter 1 Table of contents Cover Chapter 1 Table of contents Chapter 2 Declaration of conformity Chapter 3 Specifications Chapter 4 General specifications 4.1 Translation 4.2 Copyright 4.3 General descriptive names 4.4 Safety instructions 4.4.1 Use of the hazard warnings 4.4.2 General safety instructions 4.5 Overview 4.6 Intended use... - Page 4 7.5 Recharging power supply units Chapter 8 Operating elements 8.1 Status LED Chapter 9 Maintenance 9.1 General maintenance 9.2 Fuse replacement Chapter 10 Removal/disposal Chapter 11 Troubleshooting and repair 11.1 General problems Chapter 12 Spare parts and accessories 12.1 Compatible power supply units Chapter 13 Document history Chapter 14 Glossary Chapter 15 Contact information...
-
Page 5: Chapter 2 Declaration Of Conformity
Chapter 2 Declaration of conformity Chapter 2 Declaration of conformity Rev. 01... -
Page 7: Chapter 3 Specifications
Chapter 3 Specifications Chapter 3 Specifications Charging voltage max. 4,17 V Charging current max. 2,5 A Input voltage range 90...264 VAC Input current 450 mA(rms) @90 VAC Input frequency range 47...63 Hz Operating temperature 0...+40 °C Storage temperature -20...+70 °C Air humidity 10...90 % RH Protection class IP40 Dimensions (WHD) 125 x 94 x 26 mm (without power supply unit) Weight 250 g (incl. -
Page 9: Chapter 4 General Specifications
Chapter 4 General specifications Chapter 4 General specifications The information in this manual has been compiled with great care and to the best of our knowledge. The manufacturer, however, assumes no liability for any incorrect specifications that may be provided in this manual. -
Page 10: Use Of The Hazard Warnings
4.4.1 Use of the hazard warnings DANGER: Indicates a potential or threatening hazardous situation that will result in death or serious injuries if not avoided. WARNING: Indicates a potential or threatening hazardous situation that can result in death or serious injuries if not avoided. -
Page 11: Overview
Chapter 4 General specifications 4.5 Overview Top of the PSU Charger Left side of the PSU Charger 1 Button (reserverd for extension) 4 Connector port for older generations of the plug-in power supply unit 2 Connector port for the PSU to be charged 5 DC hollow plug for connecting the plug-in power supply unit included in the scope of supply 3 Status LED... -
Page 12: General Product Information
4.7 General product information This is a charger suitable for the following power supply units of the PSU family (Power Supply Unit): PSU413D+ AP (300524) PSU413D AP (300525) In addition to the current state of charge (SOC), the controller of the PSU Charger also reads additional information required for the charging process (e.g. -
Page 13: Installation Of Spare And Wear Parts
Chapter 4 General specifications 4.9 Installation of spare and wear parts Be advised that spare and accessory parts that have not been supplied by the manufacturer have also not been inspected or approved by the manufacturer. The installation and/or use of such products can possibly have a negative impact on the specified constructional properties of the device. -
Page 14: Disclaimer
For safety and warranty reasons, all internal work on the instruments beyond from that involved in normal installation and connection, must be carried out only by qualified Microtronics personnel or persons or companies authorised by Microtronics . -
Page 15: Chapter 5 Functional Principle
Chapter 5 Functional principle Chapter 5 Functional principle Functional principle Plug-in power supply (included in the scope of supply of 300697) Compatible power supply unit e.g. PSU413D+ AP (300524) PSU Charger Functions and components Plug-in power supply Plug-in power supply that can provide at least 12W at an output voltage of 12 V . -
Page 17: Chapter 6 Storage, Delivery And Transport
Support & Service Centre (see "Contact information" on page 37). The return shipment of the PSU Charger must occur in the original packaging and with freight and insurance paid to Microtronics Engineering GmbH (see "Contact information" on page 37). Insufficiently cleared return shipments will otherwise not be accepted! Rev. -
Page 19: Chapter 7 Initial Start-Up
Read this manual carefully and completely in order to ensure the proper functioning of the PSU Charger Contact Microtronics Engineering GmbH(see "Contact information" on page 37) if anything is unclear or if you encounter difficulties with regard to installation, connection or configuration. -
Page 20: Recharging Power Supply Units
7.5 Recharging power supply units Important note: Ensure setup is completed correctly. Comply with existing legal and/or operational directives. Improper handling can cause injuries and/or damage to the devices. Further safety instructions are provided in "Safety instructions" on page 9. The location for the PSU Charger must be chosen according to certain criteria. - Page 21 Chapter 7 Initial Start-Up 3. Plug the power supply unit into the PSU Charger . The Power Supply Unit is designed in such a way that it cannot be plugged in the wrong way around. The status LED should then start flashing green, indicating that the PSU is recharging.
-
Page 23: Chapter 8 Operating Elements
Chapter 8 Operating elements Chapter 8 Operating elements Operating elements 1 Button (reserverd for extension) 2 Status LED 8.1 Status LED The status LED is used both to display error codes and to indicate the current operating state. In the event of an error, the error codes listed in the following table are displayed every 5 seconds. -
Page 25: Chapter 9 Maintenance
Chapter 9 Maintenance Chapter 9 Maintenance Important note: To prevent any damage to the device, the work described in this section of the instructions must only be performed by qualified personnel. The device must be deenergised before any maintenance, cleaning and/or repair work. 9.1 General maintenance Regularly check the PSU Charger for mechanical damage. -
Page 27: Chapter 10 Removal/Disposal
Logo of the EU WEEE Directive This symbol indicates that the requirements of Directive 2012/19/EU regarding the scrap disposal of waste from electric and electronic equipment must be observed. Microtronics Engineering GmbH supports and promotes recycling and environmentally friendly, separate collection/disposal of waste from electric and electronic equipment in order to protect the environment and human health. -
Page 29: Chapter 11 Troubleshooting And Repair
Chapter 11 Troubleshooting and repair Chapter 11 Troubleshooting and repair 11.1 General problems Problem Cause/Solution The device does not respond (status Check the cable connections (see "Recharging power LED always off). supply units" on page 20) Fuse defective. Return device to manufacturer for fuse replacement (see "Return"... -
Page 31: Chapter 12 Spare Parts And Accessories
Chapter 12 Spare parts and accessories Chapter 12 Spare parts and accessories 12.1 Compatible power supply units Description Quantity Order number PSU413D+ AP 300524 PSU413D AP 300525 Rev. 01... -
Page 33: Chapter 13 Document History
Chapter 13 Document history Chapter 13 Document history Rev. Date Changes 17.06.2024 First version Rev. 01... -
Page 35: Chapter 14 Glossary
Chapter 14 Glossary Chapter 14 Glossary App centre Area of the myDatanet server for the installation and management of the IoT apps. The app models that serve as a basis for the IoT apps are obtained via the rapidM2M Store . When installing an IoT app on the myDatanet server the default settings defined when developing the app models are initially applied. - Page 36 rapidM2M timestamp Depending on the required accuracy, one of two special encodings can be used for the time stamp in rapidM2M. If the accuracy requirements are moderate, the "stamp32" data type (seconds since 1999- 12-31 00:00:00 UTC) can be used. If a higher accuracy is required, the "stamp40" data type (1/256 seconds since 1999-12-31 00:00:00 UTC) can be used.
-
Page 37: Chapter 15 Contact Information
Chapter 15 Contact information Chapter 15 Contact information Support & Service: Microtronics Engineering GmbH Hauptstrasse 7 3244 Ruprechtshofen Austria, Europe Tel. +43 (0)2756 7718023 support@microtronics.com www.microtronics.com Microtronics Engineering GmbH (Headquarters) Hauptstrasse 7 3244 Ruprechtshofen Austria, Europe Tel. +43 (0)2756 77180 Fax. - Page 38 Certified by TÜV AUSTRIA: EN ISO 9001:2015, EN ISO 14001:2015, ISO/IEC 27001:2013, EN ISO 50001:2011 for myDatanet | TÜV SÜD: ATEX Directive 2014/34/EU © Microtronics Engineering GmbH. All rights reserved. Photos: Microtronics, shutterstock.com Microtronics Engineering GmbH | www.microtronics.com Hauptstrasse 7 | 3244 Ruprechtshofen | Austria | +43 2756 77180 | office@microtronics.com 301624 | Rev.01...
Need help?
Do you have a question about the PSU413D+ AP and is the answer not in the manual?
Questions and answers