Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Harris Manuals
  4. Ultrasonic Jewelry Cleaner
  5. ProVac Plus
  6. Installation, operation & parts

Harris ProVac Plus Installation, Operation & Parts

Suction cleaner
Hide thumbs

Advertisement

Quick Links

Download this manual
ProVac Plus
Suction Cleaner
Item # 90100
INSTALLATION, OPERATION & PARTS
To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely.
SAVE THIS INSTRUCTION MANUAL
Use of aftermarket replacement parts voids warranty.
ATTENTION INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT
THE INSTALLATION, OPERATION, AND SAFE USE OF THIS CLEANER THAT MUST BE
PROVIDED TO THE END USER OF THIS PRODUCT. FAILURE TO READ AND FOLLOW
ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY.
10411 80th Avenue Pleasant Prairie, WI 53158 | Customer Care: 1-866-616-1270 | Fax: 1-866-616-1271 | HarrisPoolProducts.com
10411 80th Avenue Pleasant Prairie, WI 53158 | Customer Care: 1-866-616-1270 | Fax: 1-866-616-1271 | HarrisPoolProducts.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the ProVac Plus and is the answer not in the manual?

Questions and answers

Aileen Walton
May 29, 2025

How can I order part # 47325019042?

0

Summary of Contents for Harris ProVac Plus

  • Page 1 ProVac Plus Suction Cleaner Item # 90100 INSTALLATION, OPERATION & PARTS To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely. SAVE THIS INSTRUCTION MANUAL Use of aftermarket replacement parts voids warranty. ATTENTION INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION, AND SAFE USE OF THIS CLEANER THAT MUST BE PROVIDED TO THE END USER OF THIS PRODUCT.

  • Page 2: Assembling The Cleaner

    I. POOL PREPERATION II. ASSEMBLING THE CLEANER Step 1. Attach the Wing Before assembling and installing your cleaner, your pool should be clean and algae-free so as not to inhibit 1. Looking at the front right of the cleaner main body, the cleaner’s traction.
  • Page 3 Step 2. Attach the Seal Step 3. Attach Bumper Strap Assembly and Adjust Dive Float Restrictor 1. Locate the words ‘UP’ on the seal and face toward the main body. 1. Insert the bottom end of the strap into the slot provided on the main body.
  • Page 4 III. INSTALLING THE CLEANER Step 4. Assemble Hose & Hose Weights 1. To connect the hose sections, wet the ends in the Standard Installation pool water, then twist and push the female ends The cleaner is designed to work in a wide variety of onto the male ends.
  • Page 5 IV. CLEANER ADJUSTMENTS & OPERATION 1. Hose Too Light. If the hose rises towards the surface at an angle greater than 45°, move the weights After completing the installation, turn the pool pump closer to the cleaner, or move the first two weights on. Allow the pump to run for a couple of minutes to closer to each other.

  • Page 6: Troubleshooting

    To Install the Eyeball Diverter If the cleaner stays at one end of the pool 1. First make sure your pool pump is off. Remove 1. Check the return line water flow and redirect as the original eyeball from the return line at the pool necessary with an eyeball diverter.
  • Page 7 5. Check to ensure the cleaner is operating at the 2. If debris is still lodged inside, you must remove proper speed of 8-12 feet per minute. the flapper. First, get rid of four lids in the foot pad, unscrew it, and then remove it from the main body. 6. Check to ensure the dive float mechanism is In secession, take out the screw from baffle plate, operating freely and the dive float restrictor is pull it out and lastly, remove the flapper.

  • Page 8: Maintenance

    VI. MAINTENANCE The cleaner requires almost no maintenance. Visually inspect your cleaner from time to time to make sure that: 1. The flapper is moving freely and is not obstructed by debris. 2. The foot pad is not excessively worn. When the traction pads on the bottom have worn down, it is time for replacement.
  • Page 9 ProVac Plus Cleaner Item #’90100 PART DESCRIPTION NUMBER REQ’D 647323072000 Main Body with Square Head 647322071000 Main Body with Round Head 647323071000 Dive Float 47325020042 Foot Pad 47325019042 Pleated Seal 647323073000 Weight Holder (includes dive float restrictor set) 47323015042 Right Wing (marked with +)
  • Page 10 After 90 days, to obtain warranty replacements, defective components should be returned, transportation paid, to the place of purchase. For further Harris Pool Product’s™ service, contact Harris Pool Product’s™ cus tomer care department. No returns may be made directly to the factory without the express written authorization of Harris Pool Products™.

This manual is also suitable for:

90100