Advertisement
Quick Links
OPTIMUM
M A S C H I N E N - G E R M A N Y
Assembly instruction
Version 1.0
Machine stand
3440408
To be used on the lathes D280x700, D240x500, D250x550 and D210x400!
Keep for future reference!
17. Oktober 2008
Machine stand assembly instruction ; version 1.0
Page 1
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Optimum 3440408
- Page 1 M A S C H I N E N - G E R M A N Y Assembly instruction Version 1.0 Machine stand 3440408 To be used on the lathes D280x700, D240x500, D250x550 and D210x400! Keep for future reference! 17. Oktober 2008 Machine stand assembly instruction ;...
-
Page 2: Assembly Instruction
Always keep this document close to the lathe. INFORMATION If you are not able to solve a problem using these assembly instructions, please contact: Optimum Maschinen Germany GmbH Dr. Robert-Pfleger-Str. 26 D-96103 Hallstadt Phone: 09 00 - 19 68 220 (0.49 €/min.) - Page 3 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y Safety warnings (warning notes) 1.2.1 Classification of hazards We classify the safety warnings into various levels. The table below gives an overview of the classification of symbols (pictograms) and warning alerts for each specific danger and its (possible) consequences.
- Page 4 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y Installation and assembly 1.3.1 Requirements regarding installation site Arrange the workspace around the lathe according to the local safety regulations.
- Page 5 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y Side part Collecting tray Hexagon nut with washer Hexagon socket screw with washer Button head screw Side part Hexagon nut with...
- Page 6 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y Lathe Hexagon head cap screw with washer Hexagon head cap screw with washer Hexagon nut with washer Chip tray Hexagon head cap...
- Page 7 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y 1.3.3 Mounting the machine stand for D240x500 and D250x550 Mount the front panels to the side parts of the machine stand as shown on Fig.1-1: „Assem- bly scheme machine stand - rear view“...
- Page 8 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y Holes collecting tray Collecting tray Holes front panel Side parts Fig.1-5: Mount and drill the machine stand Screw the two front panels together using the button head screws and the hexagon nuts.
- Page 9 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y Hexagon head cap screw with washer Hexagon head cap screw with washer Hexagon nut with Hexagon nut with washer washer Fig.1-7: Mounting the machine stand...
- Page 10 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y 1.3.4 Mounting the machine stand for D210x400 Roughly align the two side parts with the mounted front panel. Put the collecting tray on the machine stand.
- Page 11 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y WARNING! Severe or lethal injuries due to damaged or insufficient stable lifting gear and load suspension gear which might break under load.
- Page 12 OPTIMUM Assembly instruction M A S C H I N E N - G E R M A N Y 1.3.5 Mounting the machine stand to the floor Fix the machine stand to the subsoil of the machine, if it is electrically connected to the lathe stationary at the installation site.
Need help?
Do you have a question about the 3440408 and is the answer not in the manual?
Questions and answers