Symbols and Terms Used Symbols and Terms Used The following symbols and pictograms are used in the manual: DANGER Always abide by this information to prevent persons from injury. WARNING Always abide by this information to prevent damage to the device. CAUTION Important information for system functionality.
Product Description Product Description In this section, we introduce the 2N Indoor Compact product, outline its application options and highlight the advantages following from its use. Basic Features 2N Indoor Compact is an internal IP/SIP unit providing audio and video communication with the 2N IP intercoms.
Part No. 91378800 Axis Part No. 01700-001 Mounting box Wall/plasterboard flush mounting box for 2N indoor answering units. Not included in the package of 2N Indoor Compact. Part No. 91378803 Axis Part No. 02320-001 Wall mounting box Wall surface mounting box for 2N indoor answering units.
Wall Installation 2N Indoor Compact is designed for flush mounting (brick, plasterboard, wood). Use the flush mounting box (Part No. 91378800), which is not included in the package. Alternatively, the product can be surface installed...
Mechanical Installation • Flush Mounting (p. 10) Flush mounting using a walled-in mounting box • On-wall mounting using a wall surface mounting box Flush Mounting Flush Mounting Box Installation (p. 10) Flush Mounting Box Device Installation (p. 12) Flush Mounting Box Installation CAUTION Before starting the mechanical installation on a selected place, make sure carefully that the preparations associated with it (drilling, wall cutting) cannot damage the electrical, gas,...
Page 11
When the mortar hardens, break off the clips and cap the box with the cover provided. Use anchoring elements to fix the device into plasterboard. To install 2N Indoor Compact into a flush mounting box, get a 2.5 mm hexagon key wrench, which is included in the package.
Wall Mounting Box Installation for Device Wall Mounting 2N Indoor Compact can be installed using a wall mounting box. The device display slope is 12% in this type of installation. Use the mounting box (Part No. 91378803), which is not included in the package.
25 cm will lead to the place. Download the Drilling template from 2N.com. Fit the wall mounting box into the predrilled holes. Pull the available cables through the box opening. Use a water level for a more precise levelling.
Power Supply Power supply must comply with PS1 class output. You can feed 2N Indoor Compact as follows: Use an Ethernet cable connected to a PoE supply or PoE supporting Ethernet switch/router. Using a 12 V / 1 A DC power adapter connected to the backside terminal board.
UL294, UL603 and UL2610. PoE Supply Connection Use a standard straight RJ-45 terminated cable to connect 2N Indoor Compact to the Ethernet. The device supports the 10BaseT and 100BaseT protocols. The Ethernet connection state is indicated by a hung-up earpiece symbol .
Page 16
Mechanical Installation Figure 1. Ethernet cable connector Figure 2. Ethernet socket unused unused unused unused WARNING This device cannot be connected directly to telecom lines (or public wireless networks) of any telecom service providers (i.e. mobile providers, landline providers or Internet provid- ers).
Call Connection (p. 24) Device Configuration Interface Access 2N Indoor Compact is configured via the administration web interface. Connect the device to the LAN IP and make sure it is properly powered. You have to know the IP address for access.
Brief Guidelines It is recommended that a password is used that is difficult to break. It is not recommended that names, places or things, especially those closely related to the user, are used in the password. For increased password security, it is recommended that: •...
Brief Guidelines Press and hold the RESET (p. 7) button. Wait until the red and green LEDs go on simultaneously on the device and the acoustic signal can be heard (approx. 15–35 s). Release the RESET button. The device announces the current IP address via the speaker automatically. NOTE The delay after pressing RESET till the first light and sound signaling is set to 15–35 s depending on the device model used.
Brief Guidelines Dynamic IP Address Setting Follow the instructions below to switch on the Static IP address mode (DCHP ON): Press and hold the RESET (p. 7) button. Wait until the red and green LEDs go on simultaneously on the device and the acoustic signal can be heard (approx.
• Display information on the device display. • Use hardware (RESET button). IP Address Retrieval Using 2N Network Scanner The application helps you find the IP addresses of all the 2N devices in the LAN. Download 2N Network Scanner from the 2N.com website.
Brief Guidelines It is recommended that a password is used that is difficult to break. It is not recommended that names, places or things, especially those closely related to the user, are used in the password. For increased password security, it is recommended that: •...
The delay after pressing RESET till the first light and sound signaling is set to 15–35 s depending on the device model used. Firmware Update We recommend that the firmware is also updated during the 2N Indoor Compact installation. Refer 2N.com for the latest FW version.
• a virtual number to start a call by entering the number via your numerical keypad • basic information. Once saved, the contact will be shown in the phone book on the device display. Make sure that the call transmitting service is enabled on the called 2N device to make a successful call.
Software Configuration Basic Orientation The home page is displayed after logging into the 2N Indoor Compact web interface. You can return to it at any time using the button located in the top left corner of the other pages of the web interface. The header of the page displays the device name (see the Device name parameter in the Services section >...
Software Configuration Device Configuration Interface Access 2N Indoor Compact is configured via the administration web interface. Connect the device to the LAN IP and make sure it is properly powered. You have to know the IP address for access. Domain Name Enter the domain name as “hostname.local”.
Software Configuration Web Configuration Interface Login Fill in the 2N Indoor Compact address or domain name into the internet browser. The login screen is now displayed. Should the login screen fail to appear, you must have typed a wrong IP address, port, domain name or the administration web server has been switched off.
Software Configuration • call duration and status (incoming, outgoing, missed, picked up elsewhere, doorbell button). The search box is used for fulltext search in the call name. The check box is used for selecting all records for bulk deletion. The selected call record can also be deleted individually using the button.
Software Configuration Events Meaning ApiAccessRequested Generated whenever the request is sent to /api/accesspoint/grantac- cess with the "success" : true result. CallSessionStateChanged Event describing the call direction/state, address, session number and call sequence number. CallStateChanged Indicates the call direction (incoming, outgoing) and opponent / SIP account identification at a call state change (ringing, connected, termi- nated).
Up to 10,000 users can be imported depending on the device type. CAUTION • Special users such as those created by My2N or 2N Access Commander are not part of the directory export. • While editing the CSV file using Microsoft Excel, remember to save the file in the CSV UTF-8 format (with separators).
(accordingly, the internal/external camera button is/is not displayed during calls and call previews). With some 2N terminal equipment in the LAN, the information sent by the 2N terminal equipment is preferred to this setting (i.e. this setting is not needed for contacts using 2N terminals or camera-less devices).
Click a date once to select a fixed holiday, click twice to select a variable holiday and click for the third time to remove the holiday from the holiday list. Calling Calling is the basic function of 2N Indoor Compact – helps you establish connections with other IP network terminal devices. The device supports the extended SIP. Calls General Settings Call Time Limit –...
SIP 1 / SIP 2 2N Indoor Compact allows two independent SIP accounts to be configured. Thus, the intercom can be registered under two phone numbers at the same time, with two different SIP exchanges, for example. Both the SIP accounts process incoming calls equivalently. Outgoing calls are primarily processed using...
Page 34
Software Configuration account SIP1. Or, if SIP1 is not registered (due to SIP exchange error, e.g.), SIP2 is automatically used for outgoing calls. Select the account number for the phone numbers included in the phone directory to specify the account to be used for outgoing calls (example: 2568/1 - calls to number 2568 go via account 1, sip:1234@192.168.1.1/2 calls to sip uri via account 2).
Page 35
Software Configuration Lowest Allowed TLS Version – set the lowest TLS version to be accepted for device connection. Verify Server Certificate – verify the SIP server public certificate against the CA certificates uploaded in the device. Client Certificate – specify the client certificate and private key used for verifying the intercom’s authority to communicate with the SIP server.
Network Identification Device ID – set the device ID to be displayed in the LAN device list in all the 2N devices in one and the same LAN. You can direct a call to this device by setting the user phone number as “device:device_ID” in these devices.
Connection to Intercoms Access Key 1, 2 – set the access key shared by the 2N answering units and intercoms. If the keys in the 2N answering units and the intercoms fail to match, the devices cannot communicate, i.e. the intercom cannot call the 2N answering unit and vice versa.
Software Configuration User Sounds 2N Indoor Compact signals variable operational statuses with a sequence of tones. If the standard signaling tones do not meet your requirements, you can modify them. Sound Mapping Sound Mapping • Busy Tone – set the busy tone to be played when the called user is busy.
Hardware Audio 2N Indoor Compact is equipped with a speaker. Set the phone call and state signaling volume control in this configuration section. Phone Call Volume Call Volume – set the phone call volume.
Page 40
RTSP Stream Address – enter the IP camera RTSP stream IP address: “rtsp://camera_ip_address/param- eter1=value&parameter2=value”, refer to the parameter table below. The parameters are specific for the selected IP camera model. If you choose another 2N IP intercom for the external camera, enter “ http:// ip_address/mjpeg_stream” or “http://ip_address/h264_stream”.
Software Configuration Parameter Description Example / Values audio audio • audio=0 (disabled) • audio=1 (enabled) frame rate fps=15 (1 to 30 fps, maximum MJPEG video codec value is 15 fps). video bitrate vbr=768 for 768 kbps vcodec video codec vcodec=h264 for codec H.264 vcodec=mjpeg for codec MJPEG vres video resolution...
System Network 2N Indoor Compact is connected to the LAN and has to be assigned a valid IP address or obtain the IP address from the LAN DCHP server. The Network section helps you configure the IP address and DHCP.
Page 43
Software Configuration To retrieve the IP address, use 2N Network Scanner, which can be downloaded freely from 2N.com. Refer to Subs. IP Address Retrieval Using 2N Network Scanner (p. 21) for details. If the network uses the RADIUS server and 802.1x-based verification of connected equipment, you can make the intercom use the EAP-MD5 or EAP-TLS authentication.
Password – enter the access password for PEAP-MSCHAPv2 authentication. Date and Time 2N Indoor Compact is equipped with a real time clock without power outage backup. Select Use Time from Internet (p. 0 to synchronize the device time with the Internet time or click...
The beta functions are provided for testing purposes exclusively. Certificates Some 2N Indoor Compact LAN services use the secure TLS protocol for communication with the other LAN devices. This protocol prevents third parties from eavesdropping on or modifying call contents. TLS is based on one/two-sided authentication, which requires certificates and private keys.
P-256) and secp384r1 (aka NIST P-384) curves only. Auto Provisioning My2N The My2N cloud platform is used for remote administration and configuration of the 2N IP devices and helps you remotely connect to the device web interface. My2N Enabled – enable connection to My2N.
Software Configuration The TR-069 protocol is utilized by the My2N cloud service. Make sure that TR-069 is enabled and Active profile set to My2N to make the device work with My2N properly. Only then the device will be able to log in to My2N periodically for configuration.
Syslog 2N Indoor Compact allows you to send system messages to the Syslog server including relevant informa- tion on the device states and processes for recording and subsequent analysis and audit. It is unnecessary to configure this service for common operations.
Page 49
The login password is saved in the configuration file. If the password is not encoded in the file or 2n is the default password, the valid configuration part will only be uploaded. This means that the configuration is uploaded, but the password remains the same, not assuming the value given in the file.
Device Control Device Control The backlit MENU buttons to the right and left help you control the device using the display. In addition to the active buttons, an icon showing the action generated by the button is displayed, refer to Icons used on the display (p.
Device Control Icons used on the display Icon Description Receiving incoming call / Starting outgoing call Rejection of incoming call / Termination of outgoing/active call Used for return to Home screen outside the call. Remove Directory DND mode Device configuration Call Log Incoming call ringtone volume up Incoming call ringtone volume down...
Page 52
Device Control Icon Description Locked, screen lock Unlocked, screen lock activated/deactivated Cancel the selection and return to the home screen. Confirmation Call info Camera Preview Device detail in Directory Camera 1 Camera 2 Back Move up Move down Door contact state display (door open too long, door open by force)
Device Control Home Screen The home screen is set as the start screen of the device, which is displayed whenever the device is activated by a or button press in the Idle mode. The device displays: • missed call icon (if the call was from a de- vice/number included in the Directory), •...
Device Control Directory Menu The Directory menu provides a list of contacts and connected external cameras. Set the Directory contacts in Directory > Device (p. 30) in the web interface. Possible ac- Perform- Action result tions ance Outgoing call set- An outgoing call is set up to the destination of the selected con- tact.
Device Control Call Log Press to display the call log. The device displays a list of all accomplished calls including date, time, status (outgoing incoming or missed ) and information on from/to which destination the call was made. Use the up/down buttons at the icons to select a call in the log.
Device Control Settings Menu A long press of the right-hand bottom button at on the Home screen displays the Device Settings menu. Here set the DND mode, screen lock, device sounds and tones and display/sys- tem properties. Do Not Disturb Mode Enable/disable the DND mode after confirmation using the left-hand lower button.
The My2N/SIP Proxy section displays the current state of the My2N/SIP Proxy connections. Language You can disable language setting using the 2N Indoor Compact display. In that case, you can only set the language in the web configuration interface, refer to Basic Settings (p.
Device Control Signaling of Operational Statuses The device generates sounds to signal changes of and switching between operational statuses. Each status change is assigned a different type of tone. See the table below for the list of signals. Sound State signaling Internal application started The internal application is launched after the power supply is turned on or the device is...
Device Control Calls In this state, connection or connection attempt is in progress with another device. The 2N Indoor Compact functions are limited, it is impossible to switch to the home page and go to menus. Possible actions are included in the table below.
Page 60
After unlocking, automatic call ending can be set in the web configuration interface Unlocking (p. 37). 2N Indoor Compact does not transmit audio to the called device. Mute call The microphone icons turns red. “Noone can hear you” is displayed in the active call.
Focus (Cannot be on Face displayed un- is se- lected.) Idle Mode 2N Indoor Compact transits into the Idle mode after a set inactivity period. Set the inactivity time- out in the Display (p. 41) > Backlight web configu- ration menu.
Device Control Device Lock When the 2N Indoor Compact lock is activated, enter the PIN code (digits 1–4) for device locking. The same PIN code is required for device unlock- ing. When the lock is activated, the device rings to signal an incoming call and displays the call- er identification including the camera preview if available.
Device Control Do Not Disturb Mode The incoming call ringtone is switched off in the DND mode. A call can be received, rejected or ended in this mode, refer to Calls (p. 59). The display shows the camera preview if availa- ble , CLIP and the Incoming call message.
Maintenance - Cleaning Maintenance - Cleaning 2N Indoor Compact contains no environmentally harmful components. Dispose of the device in accordance with the applicable legal regulations. 2N Indoor Compact contains no environmentally harmful components. Dispose of the device in accordance with the applicable legal regulations.
Technical Parameters Technical Parameters Supply type Consumption Polarity reversal Power Consumption protection in idle PoE, IEEE 802.3af 12 W ✓ 1.9 W 12 V DC ±10 % adapter; 1 A (rec- 12 W ✓ 1.9 W ommended) User interface Controls 7 capacitive buttons with white and RGB LED backlight Display 4.3"...
Page 67
Technical Parameters Audio stream Protocols RTP, RTSP Codecs G.711, G.729, G.722, L16/16kHz Video stream Protocols MJPEG, RTP, RTSP, HTTP Codecs MJPEG, H.264 Interface 10/100BaseT, RJ-45; Cat5e or higher Doorbell input Input type Switching contact (button/relay) Contact type Normally open (NO) Contact parameters Max.
Page 68
Technical Parameters Mechanical Parameters Dimensions (w x h x d) 152 × 153 × 50 mm Weight 387 g Operating temperature 0 to 50 °C Relative humidity 10 to 90 % non-condensing Storing temperature −20 °C to 70 °C Recommended altitude 0 to 2000 m...
Directives, Laws and Regulations - General Instructions and Cautions Directives, Laws and Regulations - General Instructions and Cautions 2N Indoor Compact conforms to the following directives and regulations: • 2014/30/EU for electromagnetic compatibility • 2014/35/EU for electrical equipment designed for use within certain voltage limits •...
Page 70
/ devices of other suppliers, the customer agrees that the 2N TELEKOMUNIKACE a.s. company shall not be held liable for any functionality limitation of such a product or any damage, loss or injury related to this potential functionali- ty limitation.
Page 71
• The wiring of the door relay is limited only inside of the protected area. • When the 2N product has reached the end of its useful life, dispose of it according to local laws and regulations. The product should not be disposed of together with household or commercial waste.
Page 72
Class 2 low-voltage power SELV and limited power supply. • Network Connector – Standard Ethernet wiring. Evaluated by UL when powered from. The 2N product was tested with the injector Axis 30 W MIDSPAN P/N: 02172-002. The midspan power injector can be located at any point within the defined structured cabling channel compliant to the Standard for Balanced Twisted-Pair Telecommunications Cabling and Components, ANSI/TIA-568-C.2, between the...
Important information for system functionality. Useful information for quick and efficient functionality. NOTE Routines or advice for efficient use of the device. Safety instructions WARNING The 2N product shall be installed by a trained professional, and in compliance with local laws and regulations.
Page 74
The 2N product shall be used in compliance with local laws and regulations. • 2N Telekomunikace recommends using a shielded network cable (STP). • To use the 2N product outdoors, or in similar environments, it shall be installed in an approved outdoor housing.
Need help?
Do you have a question about the Indoor Compact and is the answer not in the manual?
Questions and answers