Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for ray RIOSensor+
- Page 1 User and Installation Guide www.raymedical.com...
- Page 2 RIOSensor+ RIOSensor+ User & Installation Guide...
- Page 3 Notice The User & Installation Guide for RIOSensor+ includes information on the device as well as its installation and usage. We recommend that you familiarize yourself with this guide to make the most effective use of your system. RIOSensor+ is intended to produce images of the dento-maxillofacial region of the human anatomy at the direction of health care professionals.
-
Page 4: Table Of Contents
Using the Different Positioning Systems ....4 X-ray Source Compatibility ..... 4 Chapter 3 Computer System Requirements . -
Page 5: Conventions In This Guide
Conventions in this Guide Conventions in this Guide The following special messages emphasize information or indicate potential risk to persons or equipment: WARNING: Warns you to avoid injury to yourself or others by following the safety instructions precisely. CAUTION: Alerts you to a condition that might cause serious damage. Important: Alerts you to a condition that might cause problems. -
Page 6: Functional Components Overview
RIOSensor+ Overview Functional Components Overview RIOSensor+ Sensor: Size and Use The RIOSensor+ sensor is radio-sensitive. The active surface of the RIOSensor+ sensor is the flat surface marked with #1 or #2 indicating the size of the sensor. The following table summarizes the RIOSensor+ sensor size and typical usage: Size Size 1 (universal RIOSensor+... -
Page 7: Sharing The Riosensor+ Sensor Between Workstations
You can use different systems for positioning the RIOSensor+ sensor in the mouth. X-ray Source Compatibility The RIOSensor+ sensor is compatible with all X-ray sources that meet the current standards of intraoral radiology. We recommend a high-frequency X-ray source. The X-ray source must operate with a voltage of 60 to 70 kV. -
Page 8: Computer System Requirements
System Requirements Computer System Requirements Minimum computer system requirements for RIOSensor+ are given in the RIOSensor+ Safety, If necessary you must update your Regulatory and Technical Specifications User Guide (SMB10) computer system configuration. RIOSensor+ User & Installation Guide (SMB09)_Ed01... -
Page 9: Setting Up Riosensor
Setting Up RIOSensor+ The specific end of support for Windows 7 was January Important: 14, 2020. Microsoft strongly recommends that you move to Windows 10 to avoid a situation where you need service or support that is no longer available. The drivers that are mentioned in this document are Windows 10 compatible. - Page 10 4. Click Next. The Choose Components dialog box is displayed. Important: Do NOT uncheck any boxes that are already checked. 5. Select RIOSensor+ and click Install. The Installing dialog box is displayed: Note: If your workstation is running Microsoft Windows XP, a warning is displayed and you need to click Continue Anyway.
- Page 11 6. Click Next. When the installation is complete, the Completing the RVGDriver Setup Wizard dialog box is displayed: 7. Click Finish. Then restart your computer (recommended but not mandatory). 8. Connect the sensor to a USB 2.0 minimum port that is connected directly to the motherboard (generally located on the back of the workstation).
- Page 12 9. Click Install the software automatically (Recommended), then click Next. 10. Verify the sensor by running the post installation procedure. This step is optional. Click on your desktop to start the RIOSensor+ Service Tools. The Service Tools home page is displayed. Click Post Installation Procedure then follow the instructions on screen.
-
Page 13: Preparing The Acquisition Of A Single Image Using Riosensor
Acquiring Single Images Using RIOSensor+ Preparing the Acquisition of a Single Image Using RIOSensor+ To prepare the acquisition of a single image using RIOSensor+, follow these steps: 1. Select the sensor. 2. Connect the sensor to a USB 2.0 minimum port that is connected directly to the motherboard (generally located on the back of the workstation). - Page 14 Important: Always insert the sensor holding it horizontally for the comfort of the patient. 8. Move the X-ray source tube head close to the patient and align it with the tooth of the patient and the sensor. Important: Make sure that the tube head is not shaking.
- Page 15 Follow the user instructions of your X-ray source. The following tables provide guidelines for exposure times for an X-ray source at 70 kV and 7 mA. Add your values for the exposure time in seconds in the column on the right. If your time values are different from the suggested time values, adapt your time values until you find the best setting for your diagnostic.
-
Page 16: Acquiring A Single Image Using Riosensor
To acquire a single image using RIOSensor+, follow these steps: 1. Tell the patient to remain still. 2. Position yourself either two meters behind the X-ray source or outside the door. Important: Make sure you can keep visual contact with the patient during the X-ray. -
Page 17: Troubleshooting
The exposure time is too short; increase it (see suggested doses on page 13). The X-ray source is too far from the patient with respect to the selected dose. Check the contrast and brightness settings of the monitor and ... -
Page 18: Manufacturer's Address
Authorized Representative in the European Community EC REP TROPHY 4, rue F. Pelloutier, Croissy-Beaubourg 77435 Marne-la-Vallée Cedex 2, France Importer for the European Union according to MDR 2017/745 RAY EUROPE Sulzbach 65843 Otto-Volger Str. 9B 65843 Sulzbach Germany RIOSensor+ User & Installation Guide (SMB09)_Ed01... - Page 19 For more information, visit: www.raymedical.com SMB09 Ed01 2023-10...
Need help?
Do you have a question about the RIOSensor+ and is the answer not in the manual?
Questions and answers