Summary of Contents for Sevio R200
- Page 1 SEVIO R200 Installation guide Document ID: r200_installation_guide_en_v24_04 https://sevio.it/...
-
Page 2: Legal Information
Legal information The content of this document is provided "as-is". No warranties of any kind related to the content of this document are provided. Sevio reserves the right to review this document or withdraw it at any time without any notice. -
Page 3: Table Of Contents
Legal information.............................. 2 Version history..............................2 Safety................................4 Regulatory notices............................5 Warranty................................6 Care recommendations............................. 6 General description............................7 Package content............................... 8 Product identification and version information....................8 Mechanical installation............................9 Electrical installation............................11 Status................................16 Configuration..............................17 Document ID: r200_installation_guide_en_v24_04 https://sevio.it/... -
Page 4: Safety
Read this manual completely and gather all information on the device. Make sure that you understand it fully. Check that your application does not exceed the safe operating specifications for this device. Before installation This device should only be installed by qualified personnel. Document ID: r200_installation_guide_en_v24_04 https://sevio.it/... -
Page 5: Regulatory Notices
Regulatory notices Simplified EU declaration of conformity Hereby, Sevio Srl declares that the equipment is in compliance with EU directives. The full EU declaration of conformity and other detailed information are available at the respective product page at https://sevio.it/. United States (FCC) This device complies with Part 15 of the FCC rules subject to the following two conditions: 1. -
Page 6: Warranty
Do not use or store the device in dusty, dirty areas, connectors as well as other mechanical parts may be damaged. If the device is not working properly, contact the place of purchase, nearest Sevio distributor office or Sevio technical support. -
Page 7: General Description
It is mainly used as a network segment to isolate WAN and LAN networks. It offers Ethernet and serial, CAN bus interfaces (only for R200-RC) on the industrial automation side; while on the Networking side it provides Ethernet and cellular interfaces. -
Page 8: Package Content
Identification information is available on the left side of the device: Specification Value Notes R200 R200 router MODEL R200-SC R200 router with serial / CAN bus option MFGD YYYYMMDD Manufacturing date SERVICE TAG XXXXXXX 7-characters alphanumeric unique code given to the device REGISTRATION KEY... -
Page 9: Mechanical Installation
Aluminum Weight 300 g IP Protection IP30 32 mm 115 mm Mechanical drawings files are available at https://sevio.it/. Environmental Operating temperature -20 °C to 65 °C Storage and transport temperature -40 °C to 85 °C Operating humidity 10% to 90% RH (non condensing) - Page 10 The top of the hook must first be set on the DIN rail. Then just press down (step 1) and at the same time rotate the device until it is flush with the rail (step 2). Finally, release the force on the spring and check that it gets properly seated. Document ID: r200_installation_guide_en_v24_04 https://sevio.it/...
-
Page 11: Electrical Installation
Idle power 2.5 W Idle CPU, no ports connected Note: The equipment shall be supplied by ES1/SELV power sources according to IEC/EN 62368-1, protected by a 2.5 A fuse. Transient voltage has been considered as 1500 Vpeak. Document ID: r200_installation_guide_en_v24_04 https://sevio.it/... - Page 12 DI [1÷2] input low threshold 3.0 Vdc DI [1÷2] input high threshold 4.5 Vdc DI max frequency 10 kHz DO [1÷2] output voltage 0 Vdc +30 Vdc DO [1÷2] output current 200 mA @ V+ = 30 V Document ID: r200_installation_guide_en_v24_04 https://sevio.it/...
- Page 13 Wiring the Digital Inputs (DI) Input Input PNP Input connection NPN Input connection Wiring the Digital Outputs (DO) Load Load PNP Output connection NPN Output connection Document ID: r200_installation_guide_en_v24_04 https://sevio.it/...
- Page 14 Standard 100BASE-T External LAN 100BASE-T Local LAN (automation network) Connector type RJ-45 shielded Cable type CAT 5e or better, shielded Autonegotiation Auto MDI/MDI-X Speed 10 Mbit/s, 100 Mbit/s Duplex Full, Half Transmission distance max. 110 m Document ID: r200_installation_guide_en_v24_04 https://sevio.it/...
- Page 15 Max. Current M100 1800 mA Used for M100 connection Configure the Sevio Router when offline 500 mA through a properly set up USB flash drive All ports are protected from overcurrent and short circuit. Note: The cable must be shorter than the 5m allowed in the USB standard.
-
Page 16: Status
VPN connection in failure No active session GREEN Session in progress AMBER Session locked µSD is not inserted GREEN µSD is ready to eject AMBER µSD is in read/write mode GREEN Activity LED AMBER Connection speed LED Document ID: r200_installation_guide_en_v24_04 https://sevio.it/... -
Page 17: Configuration
Configuration The device is configurable via web server or Sevio Portal, the web application accessible via any updated web browser: 1. Open https://sevio.it/ and click on Sevio Portal in your web browser. 2. If you already have an account just log in as usual and add this new device to your list of devices, otherwise register a new account following the instructions in Sevio Portal. - Page 18 Sevio Srl - Via della Pusterla, 36 Misinto (MB) - IT Ph. +39 02 97070785 Customer service: support@sevio.it Sales department: sales@sevio.it https://sevio.it/ Document ID: r200_installation_guide_en_v24_04 https://sevio.it/...
Need help?
Do you have a question about the R200 and is the answer not in the manual?
Questions and answers