Summary of Contents for Mansfield PRO-FIT BUILDER Series
- Page 1 IMPORTANT HOME OWNER INFORMATION ® PRO-FIT BUILDER SERIES ACRYLIC BATHWARE Whirlpools, Air Massage Baths, and Bathtubs...
-
Page 2: Warning! Important Safety Instructions
INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS, READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS! INSTALL TO PERMIT ACCESS FOR SERVICING. INSTALL THIS UNIT IN ACCORDANCE WITH THE LOCAL ELECTRICAL CODE AND WITH THE MANUFACTURER’S INSTALLATION INSTRUCTIONS CONNECT ONLY TO A BRANCH CIRCUIT PROTECTED BY AN OVERCURRENT PROTECTION DEVICE RATED NOT MORE THAN 20A. - Page 3 WHIRLPOOL OPERATING INSTRUCTIONS BEFORE OPERATING THE WHIRLPOOL OR AIR MASSAGE SYSTEM, FILL THE BATH TO NORMAL BATHING LEVEL. (MINIMAL 3” BELOW OVERFLOW). OPERATION OF AIR BUTTON – Simply press the air button and the system will turn on. Press the air button again and the system will turn off.
- Page 4 AIR MASSAGE BATH OPERATING INSTRUCTIONS BEFORE OPERATING THE AIR BATH, FILL THE BATH TO NORMAL BATHING LEVEL. (MINIMAL 3” BELOW OVERFLOW). OPERATION OF AIR BUTTON - Press the air button once and the blower will power on. Press the air button a second time to turn the blower off.
- Page 5 SHIPPING PROTECTION OF THE WHIRLPOOL BATH 4. Mansfield has provided protective materials with each product to protect the unit from damage during shipping and installation. The use of any protective material is highly recommended to prevent any unnecessary damage such as scratches, abrasions or cracks.
- Page 6 15 minutes. Carefully check for leaks both while pump is activated and while the pump is turned off. Allow water to stand in bath for at least 30 minutes before draining. MANSFIELD WILL NOT BE RESPONSIBLE FOR WATER DAMAGE OF ANY KIND IN CONNECTION WITH ONE OF OUR WHIRLPOOLS.
-
Page 7: Electrical Instructions
ELECTRICAL INSTRUCTIONS WARNING: ALL ELECTRICAL CONNECTIONS SHOULD BE MADE BY A LICENSED, LOCALLY CERTIFIED ELECTRICIAN, IN ACCORDANCE WITH THE REQUIREMENTS OF THE NATIONAL ELECTRIC CODE AS WELL AS APPLICABLE STATE AND LOCAL CODES AND PROCEDURES. WARNING: RISK OF ELECTROCUTION. All whirlpool and air massage baths must be connected to a dedicated 120V 15A circuit and protected by a ground-fault circuit interrupter. - Page 8 WHIRLPOOL BATH WIRING DIAGRAM AIR MASSAGE BATH WIRING DIAGRAM...
- Page 9 APRON TRIMMING INSTRUCTIONS INSTRUCTIONS APPLICABLE TO RECTANGULAR MODELS Optional removable aprons are available with some models for alcove installations. IMPORTANT: The use of mortar or gypsum plaster mix is recommended on all installations. However, when installing a bath that requires a removable apron it is important that the bath not be raised from the subfloor more than ¼”.
- Page 10 APRON INSTALLATION INSTRUCTIONS See diagrams below for rectangular apron installation. IMPORTANT: Use of factory aprons requires the unit to be secured directly to the subfloor. The subfloor MUST be the same height as the finished floor or the apron cannot be installed. After the installer has decided the exact measurement, the panel or apron should be trimmed by following the procedures on the previous page.
- Page 11 CORNER APRON INSTALLATION INSTRUCTIONS TOOLS NEEDED FOR CORNER INSTALLING APRON: Seven (7) #10 1 ½” flathead screws (included with apron). Drill 1/8” drill bit Phillips head screwdriver Follow steps 8 – 12 under Removable Apron Installation Instructions. 2. Position apron under the bath lip. Be sure detail breaks on the apron and bath are aligned. 3.
- Page 12 OPTIONAL NAILING FLANGE KIT (FIELD INSTALLED) The optional field installed nailing flange kit is secured to the tub with tacky tape. The purpose of the nailing flange is to create a water tight seal to protect from water running behind the wall. The nailing flange may be nailed or screwed to the stud wall.
-
Page 13: Maintenance, Cleaning And Repairs
MAINTENANCE, CLEANING AND REPAIRS Your Swirl-Way ® Whirlpool is made of acrylic. Acrylic provides a beautiful, high-gloss finish that is extremely durable and is a beautiful look in any bathroom. IMPORTANT! Use the recommended information described in this section. Use of other cleaning materials and/or methods may harm your whirlpool and will void your warranty. -
Page 14: Troubleshooting
OFF THE ELECTRICAL POWER AT THE CIRCUIT BREAKER AT THE MAIN POWER SUPPLY. NOTE: The whirlpool pump housing is a sonically welded unit. It cannot be dissassembled for servicing for servicing. There are no user serviceable parts inside. Refer all service to Mansfield bathware technical service at 877-850-3060. PROBLEMS SOLUTIONS Whirlpool system is leaking. -
Page 15: Warranty
Mansfield Plumbing Products is not responsible or liable for any delays or any failure to perform due to unforeseen circumstances or causes beyond Mansfield Plumbing Products’ control, when such delays or failure is due, directly or indirectly, to acts of God, war... - Page 16 LIFE’S TOO SHORT for anything less than honest answers and practical solutions. So at Mansfield, we focus on making great products (right here in the U.S.A.) and making it easy to get them quickly. Simply put, we go about our business, so you can go about yours.
Need help?
Do you have a question about the PRO-FIT BUILDER Series and is the answer not in the manual?
Questions and answers
I have a 3060 TFS NCA 6606 tub of yours . I wanted to ask if I needed to install a ledger board. If I am naming it correctly the board that is mounted on the studs of the wall that sits under the lip of the tub. If so how do I measure this? I’m sure you don’t want all the weight of the tub and water supported by this board of I miss measure and the bottom support feet are not touching the floor. I’m not a plumber but I am installing it myself. Thank you for your help
Yes, the Mansfield PRO-FIT BUILDER Series 3060 TFS NCA 6606 tub requires a ledger board (referred to as blocking) for installation. The blocking should be placed below the tub rim to prevent deflection or movement but must not support the tub. The ledger board should be installed against wall sheathing, which runs full length to the floor. Precise vertical marks aligned with the bath rim and a 2¼” inward measurement from those marks help locate the wood strip position.
This answer is automatically generated