Download Print this page
GE HX-DU1021D Operation Instructions Manual
GE HX-DU1021D Operation Instructions Manual

GE HX-DU1021D Operation Instructions Manual

Radio modem configuration

Advertisement

Quick Links

HX-DU1021D Radio Modem Configuration Operation Instructions
一、
Instructions for setting up the test environment
1、 Connect the two radio modems to the computer using a USB-to-RS232 cable
2、Open two serial port assistants (one for sending and one for receiving).
The serial port configuration for the radio modem is as follows:
Baud rate: 115200
Data bits: 8
Parity: None
Stop bits: 1
3、 Turn on the power switch of the radio to enter the startup mode. At this time, connect the radio through
a serial port and send a command to enter the boot mode. If the serial port assistant is configured
correctly, it will display "into boot".
4、Turn the configuration switch on the test board to the GND end, and the radio outputs 'configuration
mode'. Use the command to set the transmitting and receiving frequency point, air baud rate, working
mode and other parameters.
5、Turn the configuration switch on the test board to the VCC end, and the radio will output "transparent mode".
when sending data to the transmitting radio through the serial port, the serial port assistant connected to the
receiving radio will display the same data.
HX-DU1021D User Manual
第 1 页 共 9 页

Advertisement

loading
Need help?

Need help?

Do you have a question about the HX-DU1021D and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GE HX-DU1021D

  • Page 1 HX-DU1021D User Manual HX-DU1021D Radio Modem Configuration Operation Instructions 一、 Instructions for setting up the test environment 1、 Connect the two radio modems to the computer using a USB-to-RS232 cable 2、Open two serial port assistants (one for sending and one for receiving).
  • Page 2 HX-DU1021D User Manual Power supply range: 9V-36V Configuration switch GND: configuration mode VCC: transparent mode Radio modem Antenna USB-to-RS232 cable Transmitter end Receiver end 二、Radio Configuration Command Instructions All commands end with a line feed (0x0D 0x0A), and setting commands use a space (0x20) to separate the two parameters before and after.
  • Page 3 HX-DU1021D User Manual Example: TX 868.125000 Echo "PROGRAMMED OK" 2、Command: TX Function: Query the current transmission frequency Example: TX Echo the current transmission frequency "TX XXX.XXXXX", such as "TX 868.125000" 3、Command: RX parameter Function: Set the current receiving frequency Example: RX 868.125000 Echo "PROGRAMMED OK"...
  • Page 4 HX-DU1021D User Manual Function: Query the transmission power level. Example: PWR, response the current transmission power level "X", such as "H". 9、Command: CHANNEL parameter Function: Set the current channel number, where parameter ranges from 0 to 49. Example: CHANNEL 10, response "PROGRAMMED OK".
  • Page 5 HX-DU1021D User Manual Function: Turn on or off the frequency adaptive function. The parameter is “ON” or “OFF”. Example: FAUTO ON Echo “PROGRAMMED OK” 14、Command: FAUTO Function: Query whether the frequency adaptation is enabled. Example: FAUTO Echo “FAUTO ON” or “FAUTO OFF”...
  • Page 6 HX-DU1021D User Manual Function: Query the number of channels for frequency adaptation. Example: SCAN Echo “The number of channels for frequency adaptation is XX”, such as “2” 19、Command: SBAUD parameter Function: Set the serial port baud rate, supporting 9600bps/19200bps/38400bps/57600bps/115200bps. It takes effect immediately after setting.
  • Page 7 HX-DU1021D User Manual Example: LOCID Echo “The address of the station is LOCID XX”, such as “LOCID 0” 25、Command: DESID parameter Function: Set the local address of the station. The parameter is from 0 to 65535. The receiving station may output data only when the communication destination address in the data is the station address or broadcast address (65535).
  • Page 8 HX-DU1021D User Manual Example: BOOT Echo “The version number of boot is XXXX.XX.XX” FCC regulatory compliance statement §15.19 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 9 HX-DU1021D User Manual Testing item, Frequencies, Transmit Power, Modulation Type can be selected on the test script instructions.  FCC other Parts, Part 15B Compliance Requirements for Host product manufacturer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.