Toro 30135 Operator's Manual
Toro 30135 Operator's Manual

Toro 30135 Operator's Manual

36" side discharge mower proline mid–size attachment
Hide thumbs Also See for 30135:

Advertisement

Quick Links

Form No. 3328–773
36 Side Discharge Mower
Proline Mid–Size Attachment
Model No. 30135—Serial No. 230000001 and Up
Operator's Manual
Language Name (Language Abbreviation)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 30135 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Toro 30135

  • Page 1 Form No. 3328–773 36 Side Discharge Mower Proline Mid–Size Attachment Model No. 30135—Serial No. 230000001 and Up Operator’s Manual Language Name (Language Abbreviation)
  • Page 2: Table Of Contents

    Whenever you need service, genuine Toro parts, or worthy of special attention. additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and 2002 by The Toro Company All Rights Reserved Printed in the USA...
  • Page 3: Safety

    Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 67-5360 43-8480 68-8340 85-7450 54-9220 85-7460 66-1340...
  • Page 4: Setup

    Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Note: Use the chart below to identify parts used for assembly. Description Qty. Caster Wheel Assembly Thrust Washer Installing the caster wheels Spacer Retaining Ring Carrier Frame...
  • Page 5: Installing The Caster Wheels

    Installing the Caster Wheels Installing the Carrier Frame to the Traction Unit 1. Place the spacer and 2 thrust washers onto the caster wheel fork (Fig. 2). 1. Align the carrier frame holes with the mounting holes in the traction unit frame (Fig. 3). 2.
  • Page 6: Installing The Drive Belt

    m–2556 Figure 5 1. Traction Unit Drive Pulley 3. Belt Guide (2) 2. Drive Belt 4. Left Spindle Pulley m–4729 4. Thread 2 jam nuts (1/2 inch) approximately 9 inches Figure 4 (23 cm) up on each adjusting shaft (Fig. 6). 1.
  • Page 7: Operation

    7. To tension the belt, tighten the front jam nut on each Operation adjusting shaft until the springs are compressed to 5 inch (13 cm). Measure the spring compression Note: Determine the left and right sides of the machine between the spacer and the bushing (Fig. 7). from the normal operating position.
  • Page 8: Adjusting The Height-Of-Cut

    m–6306 Figure 9 1. Upper control bar 3. Blade control switch (PTO) 2. Blade control bail Disengaging the Mower Blades (PTO) 1. Releasing blade control bail to disengage blades (Fig. 9). m–4729 Figure 10 Adjusting the Height-of-Cut 1. 2 inch (51 mm) Cut 5.
  • Page 9: Tips For Mowing Grass

    If a blade is or it is late fall when grass grows more slowly. damaged or worn, replace it immediately with a genuine TORO replacement blade. Mowing Direction Alternate mowing direction to keep the grass standing straight.
  • Page 10: Maintenance

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Maintenance Procedure Interval Each Use Mower housing—clean Blade spindle bearings – grease 8 Hours Cutting blades – check Mower housing—clean 25 Hours Caster Wheels—grease Chipped Surfaces—paint...
  • Page 11 To ensure optimum cutting edge, position A, of the blades (Fig. 14). Note performance and continued safety conformance of the this dimension. machine, use genuine TORO replacement blades. Replacement blades made by other manufacturers may Front result in non-conformance with safety standards.
  • Page 12: Correcting Cutting Unit Mismatch

    blade is not balanced, file some metal off the end of the Setting the Front-to-Rear Pitch sail area only (Fig. 15). Repeat this procedure until the blade is balanced. 1. Check the tire pressure. 2. Position the blades front-to-rear (Fig. 18). Measure at C and D locations (Fig.
  • Page 13: Setting The Side-To-Side Leveling

    MEASURE FROM CUTTING EDGE TO A LEVEL SURFACE m–2558 Figure 22 4. To change the side-to-side leveling, move the thrust washers on one caster wheel fork only. Move the thrust washers from the top of the carrier frame mounting tube to the bottom to raise the corresponding side of the mower.
  • Page 14: Replacing The Mower Belt

    m–2556 Figure 24 1. Deck Belt 4. Idler Pulley m–2547 2. Right Spindle Pulley 5. Left Spindle Pulley Figure 23 3. Idler Arm Spring 1. Carrier Frame Mounting 2. Caster Wheel Grease Tube Grease Fitting Fitting 7. Reinstall the drive belt. Refer to Replacing the Drive Belt, steps 5 and 6 on page 14.
  • Page 15: Replacing The Caster Wheel Fork Bushings

    m–2541 m–2541 Figure 27 Figure 25 1. 5 inch between the 2. Jam Nuts Spacer and Bushing 1. Jam Nuts 2. Adjusting Shaft 7. Reinstall the deck cover onto the cutting unit, then 4. Remove the worn drive belt (Fig. 26). reinstall and tighten the hand knobs.
  • Page 16: Servicing The Caster Wheels And Bearings

    m–1076 Figure 29 1. Carrier Frame Mounting 2. Bushing Tube m–4225 Figure 28 Servicing the Caster Wheels 1. Locking Pin 4. Spacer 2. Thrust Washers 5. Caster Wheel Fork and Bearings 3. Carrier Frame Mounting Tube The caster wheels rotate on a roller bearing supported by a spanner bushing.
  • Page 17: Replacing The Grass Deflector

    2. Place spacer and spring onto grass deflector. Place the L end of spring behind deck edge (Fig. 31). Note: Make sure the L end of spring is installed behind deck edge before installing the bolt as shown in figure 31. 3.
  • Page 18: Troubleshooting

    Troubleshooting Problem Possible Causes Corrective Action Abnormal vibration. Cutting blade(s) is/are bent or Install new cutting blade(s). unbalanced. Blade mounting bolt is loose. Tighten blade mounting bolt. Engine mounting bolts are Tighten engine mounting loose. bolts. Loose engine pulley, idler Tighten the appropriate pulley, or blade pulley.

Table of Contents