Advertisement
Advertisement
Table of Contents
Related Manuals for avasco SolarSpeed 3.0 south landscape
Summary of Contents for avasco SolarSpeed 3.0 south landscape
- Page 1 assembly instructions SolarSpeed south landscape 280524.ENG...
-
Page 2: Standard Components
L-profiles anchor profile + centre piece * For PVC roofs use rubber with aluminium underlay. SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date. The most recent version of this document can be found on the website. 280524.ENG... -
Page 3: Required Assembly Tools
SW8 range 15-30Nm Avasco Solar spacer prior to assembly Ensure that the roof surface where the frame will be mounted on is clean, dry, and fl at. Contaminants such as gravel, sand or pebbles can cause roof damage or installation instability. - Page 4 2 sheet metal screws (Ø6.5x19mm). Bend the panel stop to a 90° angle using a screwdriver. SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date. The most recent version of this document can be found on the website. 280524.ENG...
- Page 5 Install the C-rail end reinforcement by sliding it between the assembly triangle and the rail. Secure it with 2 sheet metal screws (Ø6.5x19mm). An indication of the locations can be calculated with our free online calculator: solarspeed.avasco.be. SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date.
- Page 6 2: aligning the rows step 2.1: plotting the rows required assembly tools: Avasco Solar spacer chalk line Tip! Make a horizontal and vertical mark on the roof using a chalk line. When setting out the markers, respect the minimum edge zones (see general notes).
- Page 7 Align the rows according to plan, taking into account the length of the panels. To easily determine the distance between the basic units, you can use the Avasco Solar spacer. Set the length of the panel on the spacer. Turn the spacer 180° and align the rows.
- Page 8 3: attaching footing system An indication of the required footing systems and ballast, their locations and the method of footing and ballasting can be calculated with our free online calculator: solarspeed.avasco.be. Several options are possible: • Go to step 3.1 for rubbers •...
- Page 9 PP footing sheet metal screws (Ø6.5x19mm) Avasco PP footings are placed under the full length of the connected basic units. This means that a footing is always placed at the beginning and end of the connected basic units.
- Page 10 3.3: installing Avasco concrete footing required components: concrete footing + hammer plug rubber protection A footing is placed at the beginning and the end of the connected basic units. A rubber is always placed under the concrete footings to protect the roof surface.
- Page 11 This can be done with an omega bracket and self-drilling screws, see specific metal substructure assembly instructions. Go to step 4. SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date. The most recent version of this document can be found on the website. 280524.ENG...
- Page 12 (provided by installer) (provided by installer) Position the Avasco SolarSpeed basic units so that the pre-installed roof anchor is precisely centered between the two C-rails. Secure the anchor profile over the roof anchor, fastening it with a washer and nut according to the roof anchor manufacturer’s installation manual.
- Page 13 4: placing the ballast An indication of the required footing systems and ballast, their locations and the method of footing and ballasting can be calculated with our free online calculator: solarspeed.avasco.be. step 4.1: providing ballast with ballast support required components:...
- Page 14 On the inner side of the installation sets of L-profiles are used when not enough ballast can be placed on ballast supports. SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date. The most recent version of this document can be found on the website. 280524.ENG...
- Page 15 (Ø6.5x19mm) Secure the backplates with 4 sheet metal screws (Ø6.5x19mm) on the basic units. SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date. The most recent version of this document can be found on the website. 280524.ENG...
- Page 16 Use 4 self- drilling screws (Ø5.5x25mm) per rail. SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date. The most recent version of this document can be found on the website. 280524.ENG...
- Page 17 SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date. The most recent version of this document can be found on the website.
-
Page 18: Step 8: Installing The Modules
2 bolts with minimum 19Nm and maximum 25Nm. (see general notes) SolarSpeed www.avasco-solar.be south landscape Any printed version may not be up-to-date. The most recent version of this document can be found on the website. 280524.ENG... -
Page 19: General Notes
It is the installer’s responsibility to always follow the latest version, which is the only valid one. This is available at all times on www.avasco-solar.be or can be obtained upon request. SolarSpeed www.avasco-solar.be... - Page 20 This allows us to continue to guarantee short delivery times, especially for your industrial projects. We deliver the materials directly to the site in Europe (intercontinental on demand). Avasco Solar plc Rodenbachstraat 53 8908 Vlamertinge - Belgium T +32 (0)57 27 15 00 VAT BE 0721.474.320...
Need help?
Do you have a question about the SolarSpeed 3.0 south landscape and is the answer not in the manual?
Questions and answers