Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for AEM LAMBRECHT meteo PROFESSIONAL-IX 3.0 Modbus
- Page 1 USER MANUAL PROFESSIONAL-IX 3.0 Modbus Wind Sensors...
-
Page 2: Table Of Contents
10.3 Standard configuration - Default 10.4 Available Modbus commands 10.5 Instantaneous values / realtime values (Input Register) 10.6 Period data - Average, maximum and minimum (Input Register) 10.7 Descriptive sensor parameter registers (Holding Register) 10.8 Configuration registers (Holding Register) Autoconfiguration Disposal Technical data page – aem.eco... -
Page 3: Features Of The Professional-Ix 3.0 Modbus
The two components are subject to spatial and temporal variations, thus, strictly speaking, they are valid only for the site where the measuring instrument is installed. Therefore, we recommend to select the place of installation very carefully. aem.eco page –... -
Page 4: General Installation Conditions
Accessories: (in accordance with the order separately packed) • Connecting cable with plug 4.4 Incoming goods inspection Please verify in detail the delivery with regard to completeness and eventual transport damages. In case of eventual claims please contact us in writing immediately. page – aem.eco... -
Page 5: Energy Supply
Put the sensor on the mast (tube). With regard to the wind direction sensor the north mark on the sensor must be aligned to the geographical north direction acc. to 5.4. Afterwards fasten the locking screw in the mast adapter to give the sensor a fixed and torsion-free fit. Proceed analogously when mounting the sensor on a tube traverse. aem.eco page –... -
Page 6: Mounting On Traverse With Slotted Borehole
Forcibly turning the permanently mounted sensor can damage the sensor. After alignment, the adhesive strips must be removed. For precise alignment, please pay attention to the compass readings. Follow all relevant safety instructions when mounting a sensor on a mast. page – aem.eco... -
Page 7: Earthing
5.7 Connection of sensor electronics PROFESSIONAL-IX 3.0 Modbus sensors will be connected to a data measuring system via the open cable end (see connection diagrams). The connecting cable is suitably installed along the mast between the data evaluation device aem.eco page –... -
Page 8: Safety Regulations
LAMBRECHT service under: Tel: +49-(0)551-4958-0 Email: support@lambrecht.net For the long-term assurance of the function and accuracy of the proposed components, we are pleased to offer you our professional maintenance and calibration services. Transports In case it is necessary to ship or to transport the sensor, the instrument must be carefully packed to prevent mechanical influences or other damages. It is recommended to use the original packing. page – aem.eco... -
Page 9: Dimensional Drawings And Connections
LAMBRECHT meteo | PROFESSIONAL-IX 3.0 Modbus Dimensional drawings and connections aem.eco page –... -
Page 10: Connection Diagrams
LAMBRECHT meteo | PROFESSIONAL-IX 3.0 Modbus Connection diagrams page – aem.eco... -
Page 11: Modbus Protocol
(2) Wind direction sensor DEFAULT ADDRESSES OF THE L AMBRECHT SENSORS Address Sensor Wind speed Wind direction Precipitation rain[e] EOLOS IND; u[sonic]WS6 com[b] PREOS ARCO u[sonic] Pyranometer 2nd Class Secondary standard Pyranometer PT100 to Modbus converter (temperature) u[sonic]WS7 aem.eco page –... -
Page 12: Available Modbus Commands
The data are valid for the period between the current request and the previous request. The maximum range of a period is 1 hour. Recalling the average value of a minimum, maximum and average group will erase the appropriate registers. Retrieve the values of a group in the sequence minimum, maximum, average. Use command: 0x03 page – aem.eco... -
Page 13: Descriptive Sensor Parameter Registers (Holding Register)
OK:8BCA Transmission Source Dest Function Func Desk Data Checksum Response <= Slave 13 Master Read Holding Register (3) Byte count=16 30 30 2E 31 36 34 38 30 2E 30 30 31 31 33 30 00 OK:6BE8 aem.eco page –... -
Page 14: Configuration Registers (Holding Register)
(waste electrical and electronic devices). Waste devices must not be disposed of with household garbage! For environmentally friendly recycling and disposal of your waste device, please contact a certified disposal company for electronic waste. Outside the EU Please observe the regulations applicable to the proper disposal of waste electronic devices in each country. page – aem.eco... -
Page 15: Technical Data
Copyright © 2024 LAMBRECHT meteo GmbH. All rights reserved. 1460x_3.0_Modbus_b-de.indd 24.24 Information in this document subject to change without notice. Photo copyright: © scharfsinn86 - Adobe stock LAMBRECHT meteo GmbH +49-(0)551-4958-0 Friedländer Weg 65-67 +49-(0)551-4958-312 37085 Göttingen E-Mail info@lambrecht.net Germany Internet www.lambrecht.net aem.eco page –...
Need help?
Do you have a question about the LAMBRECHT meteo PROFESSIONAL-IX 3.0 Modbus and is the answer not in the manual?
Questions and answers