Summary of Contents for GATENEAR SW300DC-1
- Page 1 Swing Gate Opener User Manual Read Carefully Before Use Keep for Future Reference ©2024.02...
-
Page 2: Table Of Contents
WARNING! QUICK INSTALLATION MENU Read these instructions completely before installation and use. Provide SPECIFICATIONS ……………………………………………… 03 them to any technician used to install, maintain, or repair this device and provide them with the device if it is ever given or sold to a third party. PACKAGE LIST ..…………………………………………... -
Page 3: Specifications
Quantity Picture Name SPECIFICATIONS SW300-1 SW300-2 Post Pivot Bracket(s) Single Swing Double Swing Product model SW300DC-1 SW300DC-2 Gate End Bracket(s) Input Power 110V/60Hz Rated Power 40W ea. M8x25 Bolts Est. Time to Open 90° 18-22s Max. Force 2600N 2600N ea. -
Page 4: Initial Setup
INITIAL SETUP INSTALLATION Customizing Your Gate (Installation Diagram) Step 1 - Preparing the gate before installing gate opener: Alarm Lights • Double check your gate's weight and size. Ensure that the weight of the single gate is less than 660 lb.(300kg) and the length is less than 118 in.(3m). Solar Panel •... -
Page 5: Installing Attachments And Gate Opener
• Before installing the gate opener, please ensure that the gate is correctly • Before installing the gate installed, allowing to manual move easily. The limit stop should effectively opener, please unlock it first: prevent the gate from moving further. Open the unlock cover accoroding to the direction •... -
Page 6: Accessory Setting
Circuit Board ACCESSORY SETTING Adjustment Signal Control System with Casing Alarm Antenna Buttons Terminal External Buttons 3.1 in. (78.75mm) 6.69 in.(170mm) Infrared • This product can control and drive one or two main units. Sensor • When installing this product, a leakage protection switch must be installed in a location where the door operation can be seen. -
Page 7: Infrared Sensor
Infrared Sensor (Optional) INITIAL TESTING Must be setting by professional technicians and qualified electricians. Digital Tube Display State Description • If you want to install the infrared photoelectric safety switch, please follow the When the circuit board is in operation, users can view the working status of the wiring diagram as show. -
Page 8: Adjust The Gear Setting
Adjust the Gear Setting Remote Control • Resistance Sensitivity Adjustment Knob: Remote Control Addition Adjust the sensitivity when encountering resistance. If you need to overcome environmental factors (such as strong wind), you can adjust this knob to adapt 1. Long press the "- " button for 2 seconds, the alarm will stay on, the to the changes in the environment. -
Page 9: Smart Control Board Setting
SMART CONTROL BOARD SETTING 15s (Default) Basic Setting Menu Gate Closing Time Interval • Short press "PROG" to enter the basic menu, the digital tube display shows "NE", short press "+" or "-" to select functions in the basic menu. •... -
Page 10: Advanced Setting Menu
MENU SETTINGS DEFAULT Advanced Setting Menu Short press "PROG" to Press "+" or "-" to select functions NOTICE enter the basic menu Press "SET" to confrim • Press and hold the "PROG" button for 2 seconds to enter the advanced menu. External Three-button: O/P/S the digital tube display shows "TL", short press "+"... -
Page 11: Advanced Setting Menu Instructions
Advanced Setting Menu Instructions Alarm Light Constantly Lit MENU SETTINGS DEFAULT Press and hold Press "+" or "-" to select functions NOTICE “PROG” 2 Second Press "SET" to confrim Alarm Ligh Flashing Alarm Light Motor 1 Duration After automatic learning, if the travel is not satisfactory, it can be manually adjusted. -
Page 12: Maintenance
MENU SETTINGS DEFAULT TROUBLESHOOTING Press and hold Press "+" or "-" to select functions NOTICE “PROG” 2 Second Press "SET" to confrim Heavy Duty Gate Mechanism Possible Problems Default Typical Solution(s) (digital display shown) Verify that the power supply if functioning properly. Standard Gate Mechanism The gate does not open or close Check that the fuse is not blown.
Need help?
Do you have a question about the SW300DC-1 and is the answer not in the manual?
Questions and answers