Subscribe to Our Youtube Channel
Summary of Contents for Lissmac FSE 510
- Page 1 OPERATING MANUAL Radio Remote Control LISSMAC Maschinenbau GmbH Lanzstrasse 4 D-88410 Bad Wurzach, Germany Phone +49 (0) 7564 / 307-0 Fax +49 (0) 7564 / 307-500 lissmac@lissmac.com www.lissmac.com 1/33...
- Page 2 2/33...
- Page 3 Imprint This operating manual is for: LISSMAC Radio Remote Control Manufacturer: LISSMAC Maschinenbau GmbH Lanzstraße 4 D - 88410 Bad Wurzach, Germany Phone: +49 (0) 7564 / 307 – 0 Fax: +49 (0) 7564 / 307 – 500 lissmac@lissmac.com www.lissmac.com...
- Page 4 GENERAL SAFETY NOTES Warning notices and symbols in this manual SIGNAL WORD Type and source of the hazard Consequence of non-compliance. Action to avert the danger The signal word after the hazard symbol indicates the level of danger: This signal word indicates an extremely dangerous situation. If the situation is not avoided, it DANGER will result in fatal injuries.
- Page 5 The following warning and safety symbols are used in the instructions: Observe the operating instructions Wear protective helmet Wear safety shoes No use by unauthorized persons 5/33...
- Page 6 OPERATING MANUAL Preface The present operating instructions explain the handling of the device and the intended applications possible. This operating manual contains important information in order to be able to operate the device safely, properly and economically. Compliance with the information in this operating manual helps to avoid hazards, repair costs and downtime, as well as to increase the reliability and service life of the device.
- Page 7 Notes 7/33...
-
Page 8: Table Of Contents
Table of contents 1. Properties & advantages ....................9 1.1. Intended Use Policy ......................10 1.2. Organizational measures ....................10 1.3. Choice of personnel and qualifications; basic duties ............11 1.4. Safety notices regarding the operating phases .............. 12 1.4.1. Transport, assembly and installation ..............12 1.4.2. -
Page 9: Table Of Contents 1. Properties & Advantages
1. PROPERTIES & ADVANTAGES The radio remote control enables the mobile operation of all important functions of the LISSMAC UNICUT joint cutters. Due to the compact design and the simple operation, the remote control offers the best overview in difficult cuts or tight space conditions. This increases both the ergonomics for the user and the safety of the cutting process. -
Page 10: Intended Use Policy
Use according to the operating instructions only. Immediately eliminate (have) faults that may impair safety! Intended use The LISSMAC Radio Remote Control Intended use includes following the operating manual and complying with the inspection and maintenance manual. -
Page 11: Choice Of Personnel And Qualifications; Basic Duties
To the extent necessary or required by regulations, use personal protective equipment. Obey all safety information and warnings and keep them in legible condition. Replace safety and danger notices that are damaged or can no longer be read. In the event of safety-relevant changes to the device or its operating behaviour, stop the device immediately and label it accordingly. -
Page 12: Safety Notices Regarding The Operating Phases
1.4. Safety notices regarding the operating phases 1.4.1. Transport, assembly and installation The radio remote control must be deactivated during transport. 1.4.2. Commissioning Check the radio remote control for damage before commissioning. Keep a charged spare battery or batteries ready. Test the emergency stop button for smooth operation and function before each start of work. -
Page 13: Notice On Specific Hazard Categories
The device may not be operated in case of damage. In this case, contact the company LISSMAC Maschinenbau GmbH for repair. If the device is not operated immediately after unpacking, it must be protected against humidity and dirt. -
Page 14: Device Description
2. DEVICE DESCRIPTION 2.1. Radio Remote Control Pos. 1 Joystick 1 Travel drive Pos. 13 Poti for toe-in Pos. 2 Battery warning light Pos. 14 Saw motor On/off Pos. 3 LCD Display 1 Pos. 15 Direction of rotation Saw blade Pos. -
Page 15: Technical Data
2.2. Technical Data Battery type BA225030 (NiMH) 6V / 2100mAh Operating time Approx. 12 h Temperature range -20°C ... +70°C Protection type IP 65 Weight Approx. 2 kg 2.3. Battery A fully charged battery allows up to 12 hours of operation. The battery for the remote control must be replaced when the warning light on the top of the remote control flashes. -
Page 16: Display Indications
2.4. Display indications Pos. 1 Received signal strength Strong signal. Weak signal Change location. Pos. 2 Battery Indicator Battery is fully charged. The battery is empty. In addition, an acoustic signal sounds and the LED pos. 9 flashes red. Change the battery. -
Page 17: Receiver Unit
2.5. Receiver Unit • In the outdoor area, mount the device vertically with the cable outlet facing downwards only. • If the receiver is installed in a control cabinet, a remote antenna must be mounted. • The receiver housing should be protected by suitable measures against direct solar radiation (UV radiation). -
Page 18: Receiver Connection
2.6. Receiver connection In order to be able to use the radio remote control, it must be looped into the control panel. For this purpose, the Harting® connectors must be connected to each other accordingly. 2.7. Receiver Indicator Lights Yellow • Lights up as soon as the receiver has operating voltage. Red •... -
Page 19: Operation
3. OPERATION 3.1. Safety General rules • The device may only be operated by one person. • Do not use the device in case of fatigue and exhaustion or under the influence of alcohol, drugs or medications. • Keep the device clean and operate it only in technically perfect condition. •... - Page 20 At the joint cutter on preset page 2,press the soft button for radio control (Pos. 1) Transfer control If the icon is white, the control was transferred to the radio transmitter. The control then takes place only via the radio remote control. Icon Icon colour Meaning...
-
Page 21: Controls
3.2. Controls The buttons on the top of the joysticks activate the rapid traverse for offsetting. Rapid motion The button must be held down in rapid motion. Position Icon Action Element Function Rush motion for traveling Fast steering Cutting path Fine steering Travel The left joystick controls the movement forward and backward... - Page 22 Saw hood The left linear lever raises or lowers the saw hood. Position Icon Action Element Function Lifting the hood Lowering the hood Saw blade The right linear lever raises or lowers the saw blade. Position Icon Action Element Function Lifting the saw blade Lowering the saw blade Feed rate...
- Page 23 Extraction system The switch is used to control the sludge extraction. Position Icon Action Element Function Extraction ON Extraction AUTO Engine speed The knob controls the engine speed. Position Icon Action Element Function Increase speed Reduce speed Direction of rotation Depending on the selected direction of travel, the control knob controls the direction of rotation of the saw Saw blade blade for synchronous and counter-rotation.
- Page 24 Saw motor The switch controls the saw blade drive via the saw motor. Position Icon Action Element Function Saw motor ON Saw motor OFF Track correction The knob controls the driving axle angle to improve the straight line. The correction direction depends on the set direction of travel. Position Icon Action...
- Page 25 Lateral switches The switch on the sides controls the following functions: Position Icon / LED Action Element Function All-wheel drive (4WD) ON / OFF Water pump ON / OFF Inverting the direction of travel Changeover Steering type 1 / Steering type 2 (with LED display each) Honk (*inactive) On switch...
-
Page 26: Warning Lamps
3.3. Warning lamps Warning lamps The warning LED lights up or flashes red or red/green in the event of an error. Position Icon Action Element Function -Battery Low charge level -iLOG -Chip not ® inserted Warning Error / disconnection of the radio connection 26/33... -
Page 27: Servicing
4. SERVICING 4.1. Maintenance Cleaning Do not use any sharp cleaning equipment as they may damage the surface. Do not wash the device with a high-pressure cleaner. Do not use sharp objects for cleaning. Wipe the device with a damp cloth and, rub it dry, if necessary. Maintenance The device does not contain any parts that can be serviced by the user. -
Page 28: Warranty
5. WARRANTY The warranty for this device is 12 months. For wear parts, warranty is only given if the wear is not due to operational reasons. Wear parts are those parts that are subject to operational wear when the machine is used as intended. The wear time cannot be defined in a uniform manner, it differs according to the usage intensity. - Page 29 GmbH confirms that the products, which have been specifically adapted for Lissmac, comply with the relevant directives. The LISSMAC radio remote control may/can only be used together with a LISSMAC floor saw of the UNICUT 520 / UNICUT 6X0 series.
- Page 30 HBC-radiomatic GmbH Haller Straße 45 - 53 - 74564 Crailsheim - Germany hereby declares that the following product: Radio receiver FSE 510 complies with the following relevant Union harmonisation legislation: 2006/42/EC Machinery Directive, Annex II 1 A (safety component) 2014/53/EU Radio Equipment Directive (RED)
- Page 31 EU Declaration of Conformity The manufacturer: HBC-radiomatic GmbH Haller Straße 45 - 53 - 74564 Crailsheim - Germany hereby declares that the following product: Radio transmitter spectrum B complies with the following relevant Union harmonisation legislation: 2006/42/EC Machinery Directive, Annex II 1 A (safety component) 2014/53/EU Radio Equipment Directive (RED) 2011/65/EU Directive on the restriction of hazardous substances (RoHS) The designated product also complies with the following European directives with regard to their protection objectives...
-
Page 32: Spare Parts List
7. SPARE PARTS LIST LISSMAC Radio Remote Control Specification Name Receiver complete FSE 510 Rod aerial with cable Replacement battery BA225030 Charger QA109600 Waist belt Receiver Mounting Plate HEG 165 32/33... - Page 33 33/33...
Need help?
Do you have a question about the FSE 510 and is the answer not in the manual?
Questions and answers