Summary of Contents for Manamed PlasmaFlight
- Page 1 INSTRUCTIONS FOR USE Inflatable Massage System ©2024 ManaMed LLC. All rights reserved. ManaMed, the ManaMed logo, are trademarks of ManaMed LLC Registered in the U.S. Recovery activated. TD-PFLIGHT01-IFU Rev 03...
-
Page 2: Table Of Contents
Pressure Indicator ..............6 Quick Start Instructions for Wearing and Operating PlasmaFlight ......6 Switching Modes . -
Page 3: Plasmaflight Label Symbol Descriptions
This symbol designates the degree of protection against electrical shock from the wrap as being a type B applied part. Consult instructions for use. Caution THIS DEVICE IS NON-STERILE PlasmaFlight does not require sterilization before use. Technical Data Device Box Components System Operating Environment: PlasmaFlight Take-Home Device (2) Temperature: 50ºF (10ºC) and 104ºF (40ºC) -
Page 4: Plasmaflight Labeling Information
Do not attempt to repair the device or open or remove covers. Do not remove the pump unit from the cuff. Do not attempt to modify or change the device. NEVER attempt any service while the device is in use. PlasmaFlight is a Medical Electrical Device. -
Page 5: Plasmaflight Overview
Each house control unit contains a battery and internal electronics to ensure the pump is inflating and delivering air to the leg cuffs. PlasmaFlight control unit displays the mode, timer, and air pressure of the device while turned on. Refer to “Getting Started”... -
Page 6: Getting Started
Important: Charge both device cuffs before first use. Warning: Use only the charger provided by ManaMed. The use of the wrong charger can cause excessive heat, damage to the circuit and shorten the life of the battery. -
Page 7: Switching Modes
The PlasmaFlight unit is pre-set to “Mode 1”. In order to operate the PlasmaFlight unit in “Mode 2”, tap the Power Button once while the unit is powered on. The screen on the left side of the Power Button will display “F2” and the screen on the right side of the Power Button will display “00”. The unit will start operating in “Mode 2”... -
Page 8: Cleaning And Disinfecting
Do not use an extension cord with the battery charger as it may cause overheating. Do not use the battery charger with other devices as it may cause damage to the device or battery charger. If the battery area on the PlasmaFlight system becomes overheated, discontinue using and contact ManaMed Customer Service. Charging Important: Charge both devices before first use. -
Page 9: Disposal
120 days from the date of purchase. In the event of a material breach of this warranty, upon timely written notice, ManaMed, LLC will either repair or replace the PlasmaFlight or refund the original purchase price. This will constitute the Purchaser’s sole remedy. This limited warranty does not extend to any resale or other transfer of the PlasmaFlight System by Purchaser to any other person or entity. -
Page 10: Compliance Statements And Declarations Electromagnetic Compatibility (Emc) Tables
THE PLASMAFLIGHT The PlasmaFlight is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the PlasmaFlight can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the PlasmaFlight as recommended below, according to the maximum output power of the communications equipment. - Page 11 Compliance Statements & Declarations Electromagnetic Compatibility (EMC) Tables The PlasmaFlight uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely RF Emissions CISPR11 Group 1 to cause any interference in nearby electronic equipment.
- Page 12 Manufactured For: ManaMed, LLC 2612 Sirius Dr. Denton, TX 76208 support@manamed.com www.ManaMed.com PlasmaFlight is a registered trademark of ManaMed, LLC. ManaMed and the ManaMed logo are trademarks of ManaMed, LLC. TD-PFLIGHT01-IFU, Rev. 03 Copyright 2024 ManaMed®, LLC...
- Page 13 Approval Name Role Signature / Date Electronically signed by: QMS Management Chris Cioffi Chris Cioffi Reason: Approver Representa�ve Date: Apr 10, 2024 13:38 Electronically signed by: Kelly Nolan Kelly Nolan Product Management Reason: Approver Date: Apr 10, 2024 13:43 Electronically signed by: Greg Murphy Greg Murphy Greg Murphy...
Need help?
Do you have a question about the PlasmaFlight and is the answer not in the manual?
Questions and answers