Visonic ioXpander-8 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Visonic Manuals
  4. I/O Systems
  5. ioXpander-8
  6. Installation instructions manual
Visonic ioXpander-8 Installation Instructions Manual

Visonic ioXpander-8 Installation Instructions Manual

Internal wired 8 i/o expander for powermaster-33 control panel
Hide thumbs

Advertisement

Available languages

Available languages

Table of Contents

ioXpander-8 Module
Internal wired 8 I/O expander for PowerMaster-33 control
panel
1. INTRODUCTION
The ioXpander-8 module enhances the PowerMaster-33 control panel with 8 programmable wired
zone inputs or outputs. The behavior of each wired PGM output can be configured and each wired
zone input can be set up with a location and type.
The ioXpander-8 module is optional, and can be installed in a PowerMaster-33 EXP control panel with
version 19.2 or higher.
2. INSTALLATION AND WIRING
Figure 2.1 – ioXpander-8 Mounting and Wiring
A. Clips
B. Back panel
Figure 2.2 – Location of pinouts
D-306966 ioXpander-8 Module Installation Instructions
C. Expander Module flat cable
D. Connecting devices
Installation Instructions
Fig. 1 ioXpander-8 Module
Notes for ioXpander-8 module wiring:
Wired zone terminals can be connected to a normally
closed contact of a detector, switch (for example a
tamper switch of any device), or a pushbutton, via a
2.2 K
resistor. The 12V terminal can be used to
supply 12V to low power detectors with up to 10mA
standby current drain as DA-5; PL-1; Next_PIR; Vi-
Motion; Vi-Pet.
IMPORTANT! The terminals for internal and
external sirens are DC outputs intended for 12v
sirens. Connecting a loudspeaker to any of these
outputs will cause a short circuit and will damage
the unit.
The Speech Box is a wired remote speaker and
microphone device for indoor use. It provides two-
way voice communication between the user and the
central station using the control panel.
Caution! Do not install or remove the ioXpander-8
module when the control panel is powered by AC
power or battery.
For wired zones, the control panel classifies the
events according to the resistance it measures as
shown in the table below.
E.O.L or Arming Key Resistance
Range
~0 kΩ - 1.76 kΩ
Tamper/ Short
1.77 kΩ - 2.64 kΩ
2.65 kΩ - 3.52 kΩ
3.53 kΩ - 5.26 kΩ
∞
5.26 kΩ -
Pin #1 to #8 can be configured either as zone
inputs or as PGM outputs
Figure 2.3 – Detector connection example
Zone
Arming Key
Tamper
circuit
Normal
Normal
Tamper
Tamper
Alarm
Alarm
Tamper
Tamper
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ioXpander-8 and is the answer not in the manual?

Questions and answers

Summary of Contents for Visonic ioXpander-8

  • Page 1 The behavior of each wired PGM output can be configured and each wired zone input can be set up with a location and type. The ioXpander-8 module is optional, and can be installed in a PowerMaster-33 EXP control panel with version 19.2 or higher.

  • Page 2: Specifications

    To mount the expander module as shown in Figure 2.1, complete the following steps: 1. Press downward on the expander module between the two clips to insert the module into the back panel. See Figure 2.1 ioXpander-8 Mounting and Wiring (A) to identify the clips.
  • Page 3 El módulo de expansión ioXpander-8 es optativo y se puede instalar en un panel de control PowerMaster-33 EXP, con la versión 19.2 o posterior.

  • Page 4: Especificaciones

    1. Presione hacia abajo en el módulo de expansión entre los dos clips para insertarlo en el panel posterior. Para identificar los clips, consulte la figura 2.1 (A). 2. Conecte el cable plano del módulo de expansión ioXpander-8 en el conector hembra del panel delantero, en la ranura “EXPANSIÓN”. 3. ESPECIFICACIONES Eléctrica...

  • Page 5: Installation Et Câblage

    être configurée et chaque entrée de zone câblée peut être définie avec un emplacement et un type. Le module d'extension ioXpander-8 est optionnel et peut être monté dans un panneau de commande PowerMaster-33 EXP de version 19.2 ou supérieure.

  • Page 6: Caractéristiques Techniques

    1. Poussez le module d'extension entre les deux ergots pour l'insérer dans le panneau arrière. Reportez-vous au schéma 2.1 (A) pour identifier les clips. 2. Connectez le module d'extension ioXpander-8 via le câble plat à l'emplacement d'extension « EXPANDER » du panneau avant. 3. CARACTÉRISTIQUES TECHNIQUES Caractéristiques électriques...

  • Page 7: Installazione E Cablaggio

    Istruzioni di installazione 1. INTRODUZIONE Il modulo expander ioXpander-8 migliora la centrale PowerMaster-33 con 8 ingresso e uscita di zona cablata programmabili. Il comportamento di ciascuna uscita PGM cablata può essere configurato e ciascun ingresso di zona cablato può essere configurato con una posizione e un tipo.

  • Page 8: Garanzia

    1. Premere verso il basso sul modulo Expander tra le due clip per inserire il modulo nel pannello posteriore. Per identificare le clip, vedere la Figura 2.1 (A). 2. Collegare il modulo expander ioXpander-8 mediante la piattina all’alloggiamento EXPANDER” per l’Expander nel pannello anteriore. 1. SPECIFICHE...

Table of Contents