Ashland CN ASH 112 Instruction Manual

CN ASH . FT
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed
including the following:
READ AND FOLLOW ALL SAFETY
a)
INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for indoor
and outdoor use. When products are used in outdoor applications, connect
the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or
if left unattended.
h) This is an electric product – not a toy! To avoid risk of fire, burns, personal
injury and electric shock it should not be played with or placed where small
children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of the
product when in use.
m) This product is equipped with push-in type lamps. Do not twist lamps.
n) This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product from
the outlet. Also unplug any additional strings or products that may be
attached to the product. Replace the fuse as per the User Servicing
Instructions (follow product marking for proper fuse rating) and check the
product. If the replacement fuse blows, a short-circuit may be present and
the product should be discarded.
o) Read and follow all instructions that are on the product or provided with the
product.
SAVE THESE INSTRUCTIONS.
p)
Use and Care Instructions
a) When the product is placed on a live tree, the tree should be well maintained and
fresh. Do not place on live trees in which the needles are brown or break off
easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
c) Before using or reusing, inspect product carefully. Discard any products that
have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders
or enclosures, loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed,
including tree, branches, or bushes, to avoid any undue strain or stress on the
product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from sunlight.
User Servicing Instructions
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device. Do not
unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover on top of attachment plug
towards blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse
(provided with product).
7 5 NOBLE FIR 112
SKU 10711456
e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that
should not be removed. Discard product if the attachment plug is damaged.
Replace the lamp.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on cord.
2. Unlock the burned out LED lamp by lifting the hook.
3. Pull lamp and plastic base straight out of lampholder.
4. Replace lamp with only 3.0 Volt, 20mA, push-in type LED lamp (provided
with product). Always match the hook to the tab.
5. Lock the hook of lamp base by pushing lock down into the tab.
Unlock
CAUTION:
To reduce the risk of overheating replace burned out lamps promptly Use
3.0 Volt, 20 mA lamps only.
If the new lamp base does not fit in lampholder, follow the steps below before
step 4.
a) Pull the reflector out.
b) Remove the base of burned out lamp by straightening lamp leads and gently
pull lamp out.
c) Thread leads of new lamp through holes in old base
with one lead in each hole.
d) After lamp is fully inserted into base, bend each lead
up, like other lamps in the light set
touch the contacts inside the lampholder (always match
the long lead of new lamp to the hook of lamp base).
e) Insert the reflector into the base.
CAUTION:
1. Risk of fire. This product does not contain lamp shunts, which allow the product
to operate if one lamp burns out. Replace lamps only with the spare lamps
provided with this product.
2. To reduce the risk of fire and electric shock: a) Do not install on trees having
needles, leaves or branch coverings of metal or materials which look like metal,
and b) Do not mount or support strings in a manner that can cut or damage
wire insulation.
Model No. CHL-036S
CAUTION! - CAUTION! -
ALWAYS UNPLUG YOUR TREE FROM ALWAYS UNPLUG YOUR TREE FROM
ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree stand
1 Choose a location near a wall outlet. .
2 Open the stand to a 90 degree angle until the hole lines up with the hole on .
the tube.
3 Screw an eye bolt into the hole .
#
Hook
Lock
Tab
, -
so that the leads will
.
.