Assembly Instructions - Solt GGSBFAP4W10W User Manual

Installation Procedures
PRODUCT INSTALLATION
1. Remove the air inlet grille.

Assembly Instructions

Installation Procedures
STEP 1
1. Remove the air inlet grille.
Take out the Bladeless Fan Body and assembly parts
from the box. Remove the Air Inlet Grille using the
Buckle
buckle shown below.
PRODUCT INSTALLATION
3. Remove the protective film of
the filter.
Installation Procedures
Buckle
1. Remove the air inlet grille.
2. Take out the pre-filter. Press the raised
STEP 2
5. Install the pre-filter. Align the slot
3. Remove the protective film of
part on both sides to pull it outwards
To take out the Pre-Filter, press the raised
position at the bottom and buckle up
the filter.
part on both sides to pull it outwards. Then proceed
and take out the pre-filter.
the upper U-shaped buckle.
to take out the pre-filter.
2. Take out the pre-filter. Press the raised
Buckle
part on both sides to pull it outwards
and take out the pre-filter.
3. Remove the protective film of
5. Install the pre-filter. Align the slot
the filter.
STEP 3
position at the bottom and buckle up
Remove the protective film of the filter.
4. Install the HEPA filter.
the upper U-shaped buckle.
4. Install the HEPA filter. STEP 4
Install the HEPA Filter.
7. Install the adapter,Tighten the plug
5. Install the pre-filter. Align the slot
with the socket position of the base.
position at the bottom and buckle up
6. Install the air inlet grille. Align the upper
the upper U-shaped buckle.
two buckles and press them tightly, then
press the two sides at lower part, slowly
and gently buckle the air inlet grille.
6
6. Install the air inlet grille. Align the upper
two buckles and press them tightly, then
press the two sides at lower part, slowly
and gently buckle the air inlet grille.
NOTE
It is recommended to clean the filter once every two weeks and replace it once every six months
2. Take out the pre-filter. Press the raised
part on both sides to pull it outwards
and take out the pre-filter.
5. Install the pre-filter. Align the slot
position at the bottom and buckle up
STEP 5
2. Take out the pre-filter. Press the raised
the upper U-shaped buckle.
Install the Pre-Filter. Align the slot
position at the bottom and buckle up
the upper U-shaped buckle.
4. Install the HEPA filter.
2. Take out the pre-filter. Press the raised
STEP 6
6. Install the air inlet grille. Align the upper
4. Install the HEPA filter.
Install the Air Inlet Grille. Align the upper
two buckles and press them tightly, then
two buckles and press them tightly, then
press the two sides at lower part, slowly
press the two sides at lower part, slowly
and gently buckle the air inlet grille.
and gently buckle the air inlet grille.
4. Install the HEPA filter.
7. Install the adapter,Tighten the plug
6. Install the air inlet grille. Align the upper
STEP 7
Install the adapter, then tighten the plug
with the socket position of the base.
07
8. Plug power supply.
6. Install the air inlet grille. Align the upper
STEP 8
Plug in the power supply
It is recommended to clean the filter once every two weeks and r
(the cleaning and replacement cycle can be adjusted according
07
Buckling
position
part on both sides to pull it outwards
and take out the pre-filter.
part on both sides to pull it outwards
and take out the pre-filter.
Buckling
position
with the socket position of the base.
two buckles and press them tightly, then
press the two sides at lower part, slowly
and gently buckle the air inlet grille.
two buckles and press them tightly, then
press the two sides at lower part, slowly
NOTE
and gently buckle the air inlet grille.
6. Install th
two buck
press the
and gent
07
8. Plug po
Buckling
position
Buckling
position