Summary of Contents for Sanlida HERO 10 TARGET COMPOUND BOW KIT
- Page 1 HERO 10 TARGET COMPOUND BOW KIT (Flexible Draw Wall Edition) OWNER’S MANUAL WWW.SANLIDAOUTDOOR.COM/WWW.SANLIDAARCHERY.COM...
- Page 2 OfficiallyCertifiedProductsbyWorldArchery...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Bow Owner's Personal Info Important Safety Information Packing List Terminology Key Point Cam System Draw Length Adjustment Cable Guard Adjustment Draw Weight Adjustment Instruction of Bow Press X10 Sight And Scope Bow Tunning Specifications Installation of Accessories Compound Bow Maintenance Notes... -
Page 4: Bow Owner's Personal Info
THANK YOU FOR CHOOSING SANLIDA ARCHERY Congratulation on purchase of the Hero 10 target compound bow kit. We are excited you purchased a competitive compound bow set. Every accessory in this kit is specially designed and made for competitive tournament. -
Page 5: Important Safety Information
SAFETY INFORMATION WARNING READ THIS MANUAL CAREFULLY BEFORE USING YOUR HERO X10. TO AVOID SERIOUS INJURY OR DEATH, FOLLOW THE SAFETY INFORMATION IN THIS MANUAL. △WARNING: This is a high-performance bow, you must take upon the responsibility of using it. ！... -
Page 6: Packing List
PACKINGLIST OF HERO 10 KIT 1. V-bar 2. Hero 10 compound 3. Scope fixed buckle part 1 4. Compound scope 5. Stabilizer weight 56g ×2pcs 6. Stabilizer weight 112g ×2pcs 7. Stabilizer weight 28g ×2pcs 8. Riser damper 9. Stabilizer damper 10. -
Page 7: Terminology
HERO 10 TERMINOLOGY Limbs Stabilizer Weight Bushing Limb Pocket String Stopper Limb Bolt Grip Sight Bushing D-Loop Cable Guard Rest Bushing Position Rope of Peep Stabilizer Bushing String Limb Bolt Buss Cable Limb Pocket Control Cable Limbs Upper Module Bottom Module Axle Lower Cam Upper Cam... -
Page 8: Key Point
KEY POINT Axle to Axle Brace height Key points HERO 10 CAM SYSTEM Big cam system Lower cam(big cam) Upper cam(big cam) Details of big cam draw length modules (Reminder:Each Hero 10 compound kit contains one set of draw length modules) Lower cam module (big cam) Upper cam module(big cam) - Page 9 Medium cam system Upper cam(medium cam) Lower cam(medium cam) Details of medium cam draw length modules (Reminder:Each Hero 10 compound kit contains one set of draw length modules) Upper cam modules(Medium cam) Lower cam modules(Mediu cam) Small cam system Lower cam(small cam) Upper cam(small cam) Details of small cam draw length modules (Reminder:Each Hero 10 compound kit contains one set of draw length modules)
-
Page 10: Draw Length Adjustment
Upper cam modules(small cam) Lower cam modules(small cam) Reminder: •U-Upper module •L-Lower module •B-Big cam •M-Medium cam •S-small cam •Number-Number of modules •Hero 10 compound bow uses hybrid cam system. ADJUSTING DRAW LENGTH ·When adjusting the draw length, you need to change the upper modules and lower modules at the same time. -
Page 11: Cable Guard Adjustment
CABLE GUARD ADJUSTMENT Socket head Cap Screw Counter Sunk Screw ·Move the rod a little to the direction of red arrow in the picture, turn it into appropriate angle. Then push the rod back to the position for fitting into the rod mount, and tighten it by fastening fix screws. ·This method can adjust the distance between two cables and the string to prevent the contact between arrow vane and cable when using vanes in different sizes. -
Page 12: Instruction Of Bow Press
BOW PRESS INSTRUCTION ·It is necessary to make sure the initial setup of the Axle -to -Axle , brace height, cam after the entire bow string is installed and adjusted. This will ensure the performance of the bow can be fully exerted. ·The cam synchronization means the bow string hit the draw stop peg on the upper and the stop peg of lower cams simultaneously to complete the stop motion of the cam while full draw of the bow. - Page 13 1.Is the sight firmly attached to the bow riser? 2.Is the mounting knob firmly tightened? 3.Are there any loose screws? 4.Are all moving parts moving smoothly? In the case of a problem concerning above points, abort usage immediately, and contact your archery retailer about the issue.
- Page 14 C. Sight adjustment 1.Push the adjust buttons on the Aperture Block and insert the it from the bottom of the Elevation Bar.Move the Aperture Block to the proper location, then release the button, make sure the Aperture Block and Elevation Bar are matched perfectly. Please note that the Release Lever must be fully depressed when inserting.
-
Page 15: Bow Tunning
4.Turn the left and right adjusting knob to fine adjust the left and right position of the scope. Loosen the fixing nut of the scope, screw the sight, you can quickly adjust the left and right position of the scope.After adjusting to the appropriate position, it is necessary to tighten the sight fixed nut, so as not to loosen the scope and srotate. - Page 16 2.Stabilizer quick connection Required accessories: No.12, No.16, No.19 ,No.20, No.22 Take out the screws from No. 19 and No. 12 boxes and screw them on the weight hole at the front end of the bow handle. Take out the extender, and then take out the cylindrical nut in the No. 12 box, screw it to the threaded end of the extender, without screwing it to the end, then insert the cylindrical nut into the quick release installed in the previous step, and tighten the extender.
- Page 17 3.V-bar and stabilizer Required accessories: No.1,No.5, No.6 ,No.7 ,No.9 ,No.14 Take out No.1 and V-bar, remove the nut, and then install the V-bar on the counterweight hole at the back of the riser. Take out the No.15 side rod, and then screw one of the nuts removed from the V-bar onto the end of the side rod with the screw.
- Page 18 5.Arrow rest installation and adjustment Required accessories: No.10 and No.13 Use screws from No.13 and washers to fix No.10 on the riser. The arrow rest keep level. 6.Installation of scope ,scope damper and sight Required accessories: No.3 ,No.4 ,No.17, No.21, No.23, No.24 Among them, No.23 is used for replacement and can be omitted from assembly.
- Page 19 Take out No.17, loosen the sight fixing knob, take off the main body of the sight, and install the sight mounting seat on the riser with screws. Take out No.21, (see section A of the scope manual for the subsequent text description). ( Part B)
- Page 20 Adjustment of scope and sight (Part C) Loosen the fixing screw of the scope, you can quickly adjust the left and right position of the scope. After adjusting to the proper position, the scope fixing screw needs to be tightened to prevent the scope from loosening and rotating.
-
Page 21: Compound Bow Maintenance
STRINGS AND CABLES Apply a light coat of bowstring wax to your bow’s cables and string on a regular basis. Sanlida suggests once every two weeks during peak use. Use a high quality bowstring wax available at your local Genuine Sanlida Retailer. -
Page 22: Faq
1. There is abnormal noise or vibration during use. Solution: Check the whole bow and tighten the loose screws. 2. Abnormal noise when drawing the bow. Solution: Slightly loosen the screws of the bow frame. 3. The bowstring is fluffing. Solution: Use string wax to maintain the bowstring or contact an authorized dealer to replace the bowstring. -
Page 23: Notes
NOTES... - Page 24 TEL +86-391-3216637 Email info@sanlidaarchery.com Follow us on Instagram ! Like us on facebook https://www.instagram.com/sanlidaarchery/ https://www.facebook.com/Sanlidaarchery/ Please search : sanlida archery or type the link below https://www.youtube.com/channel/UCZ7VchteVQTNtygiDlDu4zg/featured SANLIDA COMPOUND BOW LIMITED LIFETIME WARRANTY Hero X10 bow is guaranteed against manufacturing defects in material or workmanship to the original owner on all risers, limbs, limb pockets, and cam system for the life of the product.
Need help?
Do you have a question about the HERO 10 TARGET COMPOUND BOW KIT and is the answer not in the manual?
Questions and answers
what is the axle to exle length
The axle-to-axle length of the Sanlida HERO 10 TARGET COMPOUND BOW KIT is 40 inches.
This answer is automatically generated