Raytools XC3000 Series User Manual
  1. Manuals
  2. Brands
  3. Raytools Manuals
  4. Control Systems
  5. XC3000 Series
  6. User manual

Raytools XC3000 Series User Manual

Motion control system of laser cutting
Hide thumbs
Table of Contents

Advertisement

Quick Links

XC3000Series
Motion Control System of Laser Cutting - User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XC3000 Series and is the answer not in the manual?

Questions and answers

Rabbni
May 27, 2025

Parameter setting kalibrasi motor servo YASKAWA

0

Summary of Contents for Raytools XC3000 Series

  • Page 1 XC3000Series Motion Control System of Laser Cutting - User Manual...
  • Page 2 Thank you for choosing this product from Raytools! The manual provides a detailed introduction to the installation and use of the XC3000Series professional motion control system of laser cutting, including a quick start, introductions to the function, notes and more. The software must be used with a dongle.
  • Page 3 Disclaimer ▪ We will not bear any responsibility for losses and accidents caused by wrong operation or improper handling of our products. ▪ Dismantling of the product will lose all warranty claims excluding the normal replacement of worn parts and components required for maintenance or commissioning operations.

  • Page 4: Table Of Contents

    XC3000Series Motion Control System of Laser Cutting - User Manual Contents 1 Quick Start .......................1 1.1 Start Using ............................1 1.1.1 Open the Software ..............................1 1.1.2 User interface ................................. 1 1.1.3 Toolbar ..................................2 1.1.4 File Menu ................................3 1.2 Operation Flow ..........................4 1.2.1 Find the Origin .................................4 1.2.2 Calibrate ..................................
  • Page 5 XC3000Series Motion Control System of Laser Cutting - User Manual 2.1.14 MicroJoint ................................27 2.1.15 Reverse ................................28 2.1.16 Over ..................................29 2.1.17 Relief ..................................30 2.1.18 Fillet ..................................30 2.1.19 Cooling point ............................... 31 2.1.20 Sort ..................................32 2.1.21 Array ..................................34 2.1.22 Group ...................................35 2.1.23 Fly Cut ..................................36 2.1.24 Co-edge ................................
  • Page 6 XC3000Series Motion Control System of Laser Cutting - User Manual 3 Process Parameter ....................50 3.1 Process Parameter Setting ......................50 3.2 Tree-like Process Structure ......................52 3.3 Layer ............................. 52 3.4 Processing Mode ..........................52 3.5 Cutting Parameter ........................53 3.6 Other Parameters .........................53 3.7 Power Curve ..........................
  • Page 7 XC3000Series Motion Control System of Laser Cutting - User Manual 5.10 Capacitive Sensor ........................79 5.11 Height Sensor ..........................80 5.12 Lubrication ..........................82 5.13 Dust Removal ..........................83 5.14 Setting ............................84 5.15 Forced Reset ..........................85 5.16 View Tread Info .......................... 85 5.17 View ............................85 6 Status Bar .........................

  • Page 8: Quick Start

    The mainform is one of the most common used user interfaces. There are many operating areas, as shown below: 1: Menu 2: Toolbar 3: Quick Drawing Toolbar 4: Drawing Area 5: Control Panel 6: Process Toolbar 7: Log 8: Status Bar V1.0 Raytools AG © Copyright 1 |87 www.raytools.ch...

  • Page 9: Toolbar

    Some columns have a small button in the bottom right corner which is shown as . It is called "expansion button" which can be clicked to open a form with relevant parameters. Buttons mentioned above are shown in the following figure V1.0 Raytools AG © Copyright 2 |87 www.raytools.ch...

  • Page 10: File Menu

    Sensor, Hardware Info, Gas DA Correction, Machine Coordinate Info, Burn-in Test, and Auto Tuning. · Installed Tool Factory setting includes ballbar and interferometer. · Report Print the processed graphics into a paper file or PDF document. V1.0 Raytools AG © Copyright 3 |87 www.raytools.ch...

  • Page 11: Operation Flow

    After opening the software, click on Return Origin button in CNC sub-page. Select the axis and set zero (default is to select all axes). Click on Confirm button and wait for the machine to detect the origin, as shown below: V1.0 Raytools AG © Copyright 4 |87 www.raytools.ch...

  • Page 12: Calibrate

    1.2.3 Import and Optimize Graphic After the cutting head has been calibrated, import the graphic to be processed by clicking on Open button in File Menu, as shown below: V1.0 Raytools AG © Copyright 5 |87 www.raytools.ch...
  • Page 13 An interface of graphic import will pop up. Select the graphic in the disc and click on Open button. Currently supported file formats include DXF, EMW, NC, and NSP, as shown below： V1.0 Raytools AG © Copyright 6 |87 www.raytools.ch...

  • Page 14: Set Process

    Click on Open to import the graphic. Click on Cancel to cancel the importing. 1.2.4 Set Process After the graphic import is completed, some functions in the Process Setting in Home sub-page may be needed. Functions are shown below: V1.0 Raytools AG © Copyright 7 |87 www.raytools.ch...
  • Page 15 (1) Click on Process button and enter the setting page of process parameters. (2) Select the sheet material and thickness. (3) Set process parameters of the current graphic. (4) Complete setting and click on OK. V1.0 Raytools AG © Copyright 8 |87 www.raytools.ch...

  • Page 16: Plan Cutting Path

    You can also group the graphics by selecting the graphics to be grouped and clicking on button in Home or Draw. Graphics in the selected group will be a whole and the processing sequence fixed. Later sorting will not affect the processing sequence in current group. V1.0 Raytools AG © Copyright 9 |87 www.raytools.ch...

  • Page 17: Check Before Process

    Know about their positions with the icons displayed in the drawing area, as shown below: V1.0 Raytools AG © Copyright 10 |87 www.raytools.ch...
  • Page 18 If the machine is stopped with workpiece unprocessed or no change to the graphics, click on button to locate the breakpoint and move the cutting head elsewhere. Click on button to move the cutting head back to the position where it is stopped and continues processing V1.0 Raytools AG © Copyright 11 |87 www.raytools.ch...

  • Page 19: Graphic Operation

    (1) All Select: select all the graphics in current drawing. (2) Invert Selection: change current selected graphics into unselected. (3) Deselect: deselect the selected graphics. (4) Disable Quick Drag: make the graphics in current drawing area can not be dragged. V1.0 Raytools AG © Copyright 12 |87 www.raytools.ch...
  • Page 20 Select a target graphic (squares and circles are shown in below figure as an example), b. Click on Select Similar Figure, c. All squares and circles of the same size in the drawing are selected. V1.0 Raytools AG © Copyright 13 |87 www.raytools.ch...
  • Page 21 (8) Select All Outer Contour: select all outer contours in the current drawing, as follows: Click on Select All Outer Contour and all outer contours in the current drawing are selected, as shown below. V1.0 Raytools AG © Copyright 14 |87 www.raytools.ch...
  • Page 22 Select the graphic needs to be copied in current drawing. Click on Copy. Drag the graphic copied to the proper position and click on it. (13) Delete: delete the graphic, as follows： Select the graphic needs to be deleted in current drawing. Click on Delete and the graphic selected will be deleted. V1.0 Raytools AG © Copyright 15 |87 www.raytools.ch...

  • Page 23: Display

    (6) Display Micro Joint Tag: display clear marks of the micro joint used in the graphic in current drawing. Once the display functions have been completely turned on, it shows as below: V1.0 Raytools AG © Copyright 16 |87 www.raytools.ch...

  • Page 24: Nc Code

    2.1.4 Scale Select the graphic and click on the drop-down button under the Scale button in Transform function. The drop-down bar displays options to change the size of selected graphic, as shown below: V1.0 Raytools AG © Copyright 17 |87 www.raytools.ch...
  • Page 25 (2) Common Options: select the option according to needed size to scale the graphic. (3) Scale Center: set the reference point for scaling according to the positional relation of the scaled graphic and the original one. V1.0 Raytools AG © Copyright 18 |87 www.raytools.ch...

  • Page 26: Transform

    (5) Flip: select the graphic to be flipped and click on Flip. Click on anywhere in the drawing area for a reference point. Move the mouse to drag the graphic to any position and click on anywhere to complete, as shown below: V1.0 Raytools AG © Copyright 19 |87 www.raytools.ch...

  • Page 27: Leadline

    (On Endpoint), long edge (On Center of Long) and start point (On StartPoint). There are options to choose to use the leadline to the closed graphics and cross-check after added or not, as shown below: V1.0 Raytools AG © Copyright 20 |87 www.raytools.ch...

  • Page 28: Clear

    Open graphics have no contour. 2.1.7 Clear Click on Clear button in the Home sub-page. Select the graphic and click on the option in the drop-down bar to clear the used function, as shown below: V1.0 Raytools AG © Copyright 21 |87 www.raytools.ch...

  • Page 29: Start Point

    (2) Auto Start Point: select the graphic to be processed and click on Auto Start Point. Set the start point in the new interface and click on OK to complete, as shown below: V1.0 Raytools AG © Copyright 22 |87 www.raytools.ch...

  • Page 30: Zero Ref

    Way of compensation includes Expand and contract, All expand, and All contract. Select the graphic to be compensated and click on Compensate in Home sub-page. Set the parameters and click on OK to compensate the selected graphic, as shown below: V1.0 Raytools AG © Copyright 23 |87 www.raytools.ch...
  • Page 31 Read the configuration in the compensation library by selecting materials and thickness to quickly apply. Modify default parameters in the compensation library by selecting materials and thickness. (3) Compensation Way: Way of compensation includes Out Expand and In Shrink, All Out Expand, and All In Shrink. V1.0 Raytools AG © Copyright 24 |87 www.raytools.ch...

  • Page 32: Outer Cut

    Inner refers to cutting by adding a leadline inside the graphic contour. Select the graphic with leadline and click on Inner button to make the leadline being outside the contour, as shown below: V1.0 Raytools AG © Copyright 25 |87 www.raytools.ch...

  • Page 33: Ring Cut

    OutsideCut Type: select the arc or triangle as the contour of outside cutting. OutsideCut Length: set the perimeter of the contour of outside cutting. ShortestSide Length: set the shortest edge length. The graphic added with ring cut is shown on the left. V1.0 Raytools AG © Copyright 26 |87 www.raytools.ch...

  • Page 34: Microjoint

    Joint by Distance: the micro connection added by fixed distance. (2) Parameter Count: the amount of micro joint in each contour. Length: the length of the micro joint. V1.0 Raytools AG © Copyright 27 |87 www.raytools.ch...

  • Page 35: Reverse

    Adjust the processing direction. (1) Reverse: if the processing direction now is clockwise, select the graphic and click on Reverse. Then, the selected graphic will be processed in an anticlockwise direction, as shown below: V1.0 Raytools AG © Copyright 28 |87 www.raytools.ch...

  • Page 36: Over

    Set the overcut length for the selected contour. Select the graphic to be overcut and click on Over button in the Home sub-page. Set the overcut length and click on OK to complete, as shown below: V1.0 Raytools AG © Copyright 29 |87 www.raytools.ch...

  • Page 37: Relief

    Select the graphic needs fillet and click on Fillet button in the Home sub-page. Set the fillet radius and click on OK. Then, click on the corner of the graphic to complete. The setting of fillet is shown as below: V1.0 Raytools AG © Copyright 30 |87 www.raytools.ch...

  • Page 38: Cooling Point

    Select the graphic that needs cooling point and click on the drop-down button on the right of Cooling Point. Click on Auto Cooling Point in the pop-up drop-down bar. Set the parameter of the cooling point and click on OK to complete, as shown below: V1.0 Raytools AG © Copyright 31 |87 www.raytools.ch...

  • Page 39: Sort

    Sort to see there are several ways to sort. Select the graphics and click on one way to sort. The graphics will be sorted in that way. Ways of sorting are shown below: V1.0 Raytools AG © Copyright 32 |87 www.raytools.ch...
  • Page 40 Move Prior: select one graphic among graphics, and click on the button to make it move forward. Move Next: select one graphic among graphics, and click on the button to make it move backward. V1.0 Raytools AG © Copyright 33 |87 www.raytools.ch...

  • Page 41: Array

    ·Row / Column Num: the number of row and column in the array (Row / Column) Distance / Offset: the distance and offset valu · ·Up / Down / Left / Right: directions of the array (2) Circular V1.0 Raytools AG © Copyright 34 |87 www.raytools.ch...

  • Page 42: Group

    Then, the graphics will not change if sort or drag them. Click on the drop-down button of Group to see the drop-down bar, as shown below: V1.0 Raytools AG © Copyright 35 |87 www.raytools.ch...

  • Page 43: Fly Cut

    ·Explode: select the graphic and click on Explode. The selected graphic will be broken up into the smallest segments of a line (arcs or lines). 2.1.23 Fly Cut Set the selected graphics as the path and layer. The parameter setting is shown below: V1.0 Raytools AG © Copyright 36 |87 www.raytools.ch...

  • Page 44: Co-Edge

    T-type or common co-edge, and the way to sort. Click on OK to complete. After co-edging, the graphics will be grouped into one contour to avoid sorting errors. The result of co-edge is shown below: V1.0 Raytools AG © Copyright 37 |87 www.raytools.ch...

  • Page 45: Bridge

    Click on Measure button in the Home sub-page. According to prompts in the log, click on the start and end points in drawing area. The measuring result will display in the log of drawing, as shown below: V1.0 Raytools AG © Copyright 38 |87 www.raytools.ch...

  • Page 46: Optimize

    (2) Break Line: click on Break Line and then click on the point on the graphic contour to break it. The process can be continuous and can be canceled by pressing the ESC button, as shown below: V1.0 Raytools AG © Copyright 39 |87 www.raytools.ch...
  • Page 47 Segment button and set the MerTolerance, merging tolerance which refers to if the interval of the nearest breakpoints of two contours is within the tolerance, the contours will be jointed together. After tolerance setting, click on OK to complete, as shown below: V1.0 Raytools AG © Copyright 40 |87 www.raytools.ch...

  • Page 48: Draw

    It is suggested to use the Circle for drawing the graphics. 2.2.4 Polyline Click on the drop-down button under Polyline button in Draw sub-page to see the drop-down bar which includes Polyline, Polygon, and Star for drawing. V1.0 Raytools AG © Copyright 41 |87 www.raytools.ch...

  • Page 49: Point

    Click on Text button in the Draw sub-page. Set the font and its size, input the text, and select to use Outline Font (Normal) or Single Line. After setting the parameter, click on OK and then click in the drawing area to complete the text insert. V1.0 Raytools AG © Copyright 42 |87 www.raytools.ch...

  • Page 50: Clip

    Buttons to quickly align are shown as follows: 2.2.11 Optimize The operation of this function is the same as the Optimize in the Home sub-page. For more details, please refer to 2.1.27. V1.0 Raytools AG © Copyright 43 |87 www.raytools.ch...

  • Page 51: Nest

    XC3000has equipped the function of auto-nesting. This section will describe the function in detail, so users can better use the software and improve processing efficiency. Select the Nest sub-page and import or draw a graphic. The following rectangle is drawn as an example: V1.0 Raytools AG © Copyright 44 |87 www.raytools.ch...
  • Page 52 Set the selected graphic as a part: right-click in the drawing area and select Add to Part List, Input Count. In the pop-up interface, set the part quantity and its internal sorting method. If select to group selected shapes into one part, all the selected graphics will be a part. V1.0 Raytools AG © Copyright 45 |87 www.raytools.ch...

  • Page 53: Nesting

    With parts in the drawing area, there will be a left sidebar for nesting. You can set parts and plates in the sidebar. (1) Quick Access Toolbar: quickly select, delete and nest parts and plates. (2) Part Bar: display all the added parts. V1.0 Raytools AG © Copyright 46 |87 www.raytools.ch...

  • Page 54: Nesting Parameter

    (3) Auto Sorting: set the sorting way and the nesting direction of the parts. (4) Part Parameter: select the parts to nest. (5) Clear the previous nesting results: whether to continue the nesting on the former results. (6) Advanced: click to set the advanced parameters. V1.0 Raytools AG © Copyright 47 |87 www.raytools.ch...

  • Page 55: Advanced Parameter

    Merge common: turn on the function and complete the nesting on co-edged parts. j. AutoNEST strategy: select grid to sort the parts in rows and select compact to sort into any space. V1.0 Raytools AG © Copyright 48 |87 www.raytools.ch...

  • Page 56: Plate

    Right-click to select different ways to delete. Delete: delete current selected graphic. Delete Selected Results: delete current selected graphics. Delete All Results: after deleting all the plates in the plate list, progress as normal. V1.0 Raytools AG © Copyright 49 |87 www.raytools.ch...

  • Page 57: Process Parameter

    (1) Cutting, Piercing, and Advanced Parameter (2) Remark (7) Layer (3) Import and Export (8) Mode (9) Cutting (4) Material Configuration (5) OK, Cancel, and Apply (10) Other Parameters (11) Power Curve V1.0 Raytools AG © Copyright 50 |87 www.raytools.ch...
  • Page 58 Take adding BR in the following figure as an example: After adding BR, add its thickness by right-clicking on the material, BR. V1.0 Raytools AG © Copyright 51 |87 www.raytools.ch...

  • Page 59: Tree-Like Process Structure

    There is also a function of auto-group prepiercing which can be selected in the global parameter Processing mode Select standard or fixed height cutting. Fixed height cutting refers to cutting at a fixed height. V1.0 Raytools AG © Copyright 52 |87 www.raytools.ch...

  • Page 60: Cutting Parameter

    Set the laser frequency when slow stopping. Beam off early The distance to turn the beam off in advance before reaching the end of cutting path. Control mode Set the control mode of slow stop. V1.0 Raytools AG © Copyright 53 |87 www.raytools.ch...

  • Page 61: Power Curve

    There are two power - speed curves, Duty cycle and Frequency. Users can select any option for needs. It is suggested to select the Duty cycle curve only, which has an obvious effect and is easy to adjust. Click on Edit button to edit the curves in another interface, as shown below: V1.0 Raytools AG © Copyright 54 |87 www.raytools.ch...

  • Page 62: Piercing

    When it is 100%, it means the average power equals the peak power. Start Focus Set the focus position when start piercing. Extra blow (ms) It refers to the time of no laser and blowing gas only for cooling the plate after piercing. V1.0 Raytools AG © Copyright 55 |87 www.raytools.ch...
  • Page 63 The suppression is used for both thin and thick sheets. Please select the type according to SuppresType your need Level The higher the level of suppression, the slower the response is. V1.0 Raytools AG © Copyright 56 |87 www.raytools.ch...

  • Page 64: Remark

    Set the Circle of cutting nozzle when removing slags. 3.10 Remark Users can input some notes of the current process and other relevant information, like the nozzle size, according to the needs in the Remark interface. V1.0 Raytools AG © Copyright 57 |87 www.raytools.ch...

  • Page 65: Import And Export

    The default is fine, and modify it if there are any special circumstances. XY axis travel setting Same Set the X and Y axis to be the same or separate with different parameters. V1.0 Raytools AG © Copyright 58 |87 www.raytools.ch...
  • Page 66 “m/min”, “mm/s”, “inch/min”, and “inch/s” are available. Unit of Acceleration mm/s^2 “mm/s^2”, “inch/s^2”, and “G(10m)/s^2” are available. Unit of Gas pressure “BAR”, “PSI” and “MPa” are available. Unit of Power rating “W” and “%” are available. V1.0 Raytools AG © Copyright 59 |87 www.raytools.ch...

  • Page 67: Ok, Cancel And Apply

    · Cancel: click on Cancel and the parameters set for the layer will be ineffective with the interface closed. · Apply: click on Apply after modifying the parameters for the layer. The parameters will be effective with the interface kept open. V1.0 Raytools AG © Copyright 60 |87 www.raytools.ch...

  • Page 68: Material Configuration

    The following is an example of adding a new type of material: a. Input the ID, Material, and its Name (EN as abbreviation). Then select Add button. Note that the ID and name of Material must not be the same as the existing materials, as follows: V1.0 Raytools AG © Copyright 61 |87 www.raytools.ch...
  • Page 69 Or, you may select it and click on Modify button to change it into another type of material with corresponding information. The operation on thickness of material is alike to the type, so it will not be repeated here. V1.0 Raytools AG © Copyright 62 |87 www.raytools.ch...

  • Page 70: Control Panel

    The correspondence between the machine coordinate systems and the workpiece coordinate system is shown below: Click on Preview button in the control panel to display the positional relationship between the machine and graphic. V1.0 Raytools AG © Copyright 63 |87 www.raytools.ch...

  • Page 71: Machine Coordinate System

    The program coordinate system contains a floating coordinate and workpiece coordinates. The button at the top of the control panel is used to select the floating coordinate system and other nine workpiece coordinate systems. V1.0 Raytools AG © Copyright 64 |87 www.raytools.ch...
  • Page 72 The zero point of the floating system is automatically set to the current position of the laser head when the user clicks on Frame, Dry run, or Start button in the control panel, as shown below: V1.0 Raytools AG © Copyright 65 |87 www.raytools.ch...
  • Page 73 You can choose to display either machine (mechanical) or program coordinate and set the origin for both coordinate systems. Select "Set current point as program zero" to position the cutting head at the specified coordinates. V1.0 Raytools AG © Copyright 66 |87 www.raytools.ch...

  • Page 74: Manual Control

    ：click on Follow to bring the cutting head to a distance of 1mm from the plate. Click on Follow again to cancel the following state and auto perform a Z-axis lifting. V1.0 Raytools AG © Copyright 67 |87 www.raytools.ch...
  • Page 75 Release the button for moving axis, and the jog cutting will stop. After each axis motion, the button will auto-deselect. Click on to open the setting of the jog cutting, as shown on the left: V1.0 Raytools AG © Copyright 68 |87 www.raytools.ch...

  • Page 76: Processing Control

    ：click on Frame, and the cutting head will move along the outer contour of the graphic in a rectangle shape for users to observe the graphic position in the plate. ：simulate before processing. Click on Simu, and confirm the cutting path by simulation. V1.0 Raytools AG © Copyright 69 |87 www.raytools.ch...
  • Page 77 · Loop interval: refers to the time to wait after processing to start a new one. · Mode: Normal refers to cutting and DryRun refers to run without beam, gas, or following-up. Clear cutting count: select to clear the previous processing count V1.0 Raytools AG © Copyright 70 |87 www.raytools.ch...
  • Page 78 And click on Start to process only the selected graphic. select to use the soft limit protection. select to make the machine auto-detect edges before start processing. set the manual forward or backward motion distance and speed. V1.0 Raytools AG © Copyright 71 |87 www.raytools.ch...
  • Page 79 · Finished: display the completed count. · Clear: clear current completed count. · Aft task done: there are corresponding prompts after the processing plan has been completed. · Pause: select to pause the count of processing. V1.0 Raytools AG © Copyright 72 |87 www.raytools.ch...

  • Page 80: Cnc Function

    · Simulation Speed: the speed of the cutting simulation. 5.2 Motor Enable The servo will be auto power-on when opening the software. Only with power can the machine work. Users can also click on Motor Enable to control. V1.0 Raytools AG © Copyright 73 |87 www.raytools.ch...

  • Page 81: Return Origin

    The way of edge detection includes auto, manual, and disc centering. Auto-detect edge by 3-point or 6-point. · Auto Edge Detection Click on the drop-down button under Edge Detect button in the CNC sub-page. Select Auto Edge Detect and the setting interface will pop up, as shown below: V1.0 Raytools AG © Copyright 74 |87 www.raytools.ch...
  • Page 82 · Edge detection method: 3-point and 6-point. It is suggested to use the 6-point edge detection on the thin sheet. Detect the edge by a single point 6 times to avoid interference from the tooth tip to the edge detection on a thin sheet. V1.0 Raytools AG © Copyright 75 |87 www.raytools.ch...
  • Page 83 X-axis edge. Click on P2 to obtain the coordinate of Point 2. Click on Calculate Angle, and the setting completes. The result will be shown below the drawing area, as shown below: V1.0 Raytools AG © Copyright 76 |87 www.raytools.ch...
  • Page 84 · Detect from the current position of the cutting head: select, and the edge detection will start from the current position of the cutting head. After selecting, please move the cutting head into the range of the sheet to make sure there is a sheet under cutting head. V1.0 Raytools AG © Copyright 77 |87 www.raytools.ch...

  • Page 85: Arc Detect

    Users can customize the maintenance prompt, the reminder period, to use the processing time or the system time for the reminder, to use the alarm or popup to remind, and the advance reminding time. V1.0 Raytools AG © Copyright 78 |87 www.raytools.ch...

  • Page 86: Capacitive Sensor

    Click on the drop-down button of Calibrate in the CNC sub-page, and then the drop-down bar will pop up. At where there is the plate below the cutting head, click on Quick Calibrate button in the bar to calibrate the cutting head. V1.0 Raytools AG © Copyright 79 |87 www.raytools.ch...

  • Page 87: Height Sensor

    Parameter definition: during calibration, when the cutting head is seeking the plate, if the absolute value of the difference between the capacitance value of the current cycle and the capacitance value of the V1.0 Raytools AG © Copyright 80 |87 www.raytools.ch...
  • Page 88 Parameter Default Remark Slow speed It refers to the axis speed when it is controlled manually. It refers to the axis speed when it is controlled manually in quick Rapid speed mode V1.0 Raytools AG © Copyright 81 |87 www.raytools.ch...

  • Page 89: Lubrication

    Click on Lubrication button in the CNC sub-page, and the setting interface will pop up. Users can check the time to do the next lubrication, or click on Oil Now to lubricate the machine at once, as shown below: V1.0 Raytools AG © Copyright 82 |87 www.raytools.ch...

  • Page 90: Dust Removal

    Click on Dust Removal button in the CNC sub-page, and the setting interface will pop up. Users can set the function open or closed, and timed output. There are also selections for all on or all off, as shown below: V1.0 Raytools AG © Copyright 83 |87 www.raytools.ch...

  • Page 91: Setting

    Manually move z-axis downwards to avoid touch plate: turn on the touch-plate detection when Z axis moving. Auto lifting when Z-axis touches plate: turn on the function of Z-axis lifting when touching plate. V1.0 Raytools AG © Copyright 84 |87 www.raytools.ch...

  • Page 92: Forced Reset

    Click on the drop-down button of Overview in the CNC sub-page. Select View Tread Info to see the system status. 5.17 View The sub-page next to the CNC is View. Click on View to switch the language. The language setting takes effect after re-open the software. V1.0 Raytools AG © Copyright 85 |87 www.raytools.ch...

  • Page 93: Status Bar

    The drawing log reminds and leads the operations when the user is drawing or editing the graphics, as shown below: 6.2 Log The system log is mainly used to record the operations to the system, as shown below: V1.0 Raytools AG © Copyright 86 |87 www.raytools.ch...

  • Page 94: System

    Note: when a red alarm displays in the status bar, it is needed to clear the alarm before processing. If it is a grey or white prompt, it does not matter to the processing. V1.0 Raytools AG © Copyright 87 |87 www.raytools.ch...

Table of Contents

Save PDF