Page 1
SN25HW76MM Dishwasher EN Information for Use Register your appliance on My Siemens and discover exclusive services and offers. Siemens Home Appliances...
Further information and explanations are available online: Table of contents 1 Safety ........... 4 8 Features........ 23 1.1 General information.... 4 8.1 Top basket....... 23 1.2 Intended use...... 4 8.2 Etagere ........ 24 1.3 Restriction on user group.. 4 8.3 Bottom basket ...... 24 1.4 Safe installation ......
Page 3
20 Customer Service.... 53 13.2 Arrange tableware .... 33 20.1 Product number (E-Nr.), 13.3 Removing tableware.... 35 production number (FD) 14 Basic operation ....... 35 and consecutive numbering (Z-Nr.) ........ 53 14.1 Switching on the appliance ... 35 20.2 AQUA-STOP guarantee .. 53 14.2 Setting a programme ....
en Safety 1 Safety Observe the following safety instructions. 1.1 General information Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe ¡ for future reference or for the next owner. Do not connect the appliance if it has been damaged in transit. ¡...
Page 5
Safety en WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. Connect and operate the appliance only in accordance with the ▶ specifications on the rating plate. Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating cur- ▶...
en Safety Contact between the appliance and installation lines may lead to a defect in these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can ignite. A damaged power line can cause a short circuit. Check that there is a distance of at least 5 cm between the ap- ▶...
Safety en Do not sit or stand on the appliance door when open. ▶ Knives and utensils with sharp points can cause injuries. Arrange knives and utensils with sharp points in the cutlery bas- ▶ ket with the points downwards, on the knife shelf or in the cut- lery drawer.
en Safety If the appliance or the power cord is damaged, immediately un- ▶ plug the power cord or switch off the fuse in the fuse box and turn off the water tap. Call customer services. → Page 53 ▶ Improper repairs are dangerous. Repairs to the appliance should only be carried out by trained ▶...
Page 9
Safety en WARNING ‒ Risk of crushing! With higher-level appliances, children can become crushed between the appliance door and cabinet doors underneath. Keep an eye on children when opening and closing the appli- ▶ ance door. WARNING ‒ Risk of chemical burns! Rinse aid and detergent may cause chemical burns to the mouth, throat and eyes.
en Preventing material damage Modified or damaged water hoses Preventing material damage 2 Preventing material may result in material damage and damage to the appliance. damage Never kink, crush, modify or cut ▶ through water hoses. Preventing material damage 2.1 Safe installation Only use the water hoses supplied ▶...
Environmental protection and saving energy en So as not to scratch the finish on Change the sensor setting to the de- ▶ the appliance, do not use sponges fault. with a rough surface or abrasive a Consumption is reduced. cleaning agents. → "Sensors", Page 11 To prevent corrosion, do not use ▶...
en Installation and connection walls. If you subsequently install your Sensor set- Description dishwasher as a free-standing appli- ting ance, you must stop it from tipping ergy and water con- over, e.g. by screwing it to the wall or sumption are adjus- installing it under a continuous work- ted accordingly.
Installation and connection en 4.4 Drinking water connec- tion Connect your appliance to a drinking water connection. Installing the drinking water connection Note If you are replacing the appliance, ¡ you must use a new water supply hose. Consult the installation instructions supplied for the steps required here.
en Familiarising yourself with your appliance Familiarising yourself with your appliance 5 Familiarising yourself with your appliance Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with E number and FD num- ber → Page 53.
Page 15
Familiarising yourself with your appliance en Detergent dispenser Add detergent to the detergent dispenser. → "Detergent", Page 30 Bottom basket Bottom basket → Page 24 Dispenser for special salt Add special salt to the dispenser for spe- cial salt. → "Water softening system", Page 27 Lower spray arm The lower spray arm washes the table- ware in the bottom basket.
en Familiarising yourself with your appliance 5.2 Controls You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. With some buttons you can perform different functions. 4 5 6 ON/OFF button and reset Switching on the appliance button...
Familiarising yourself with your appliance en Programme buttons and addi- Programmes tional functions → "Programmes", Page 19 Additional functions → "Additional functions", Page 22 Start button Starting the programme → Page 35 button If you press for approx. 3 seconds, you can open the basic set- tings. → "Changing basic settings", Page 39 Remote Start...
Page 18
en Familiarising yourself with your appliance Symbol Description If the water inflow or drainage malfunctions, the symbol lights up or flashes on the display. → "Troubleshooting", Page 45...
Page 19
Programmes en Programmes 6 Programmes You can find an overview of the pro- ted. The running time will change if Programmes grammes that can be selected here. the rinse aid system is switched off Different programmes, which can be or rinse aid needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
Programmes en Press the right programme button. Press the button for the relevant additional function. Press for 3 seconds. The selected programme and the additional function will flash. flashes. The programme and the additional function are saved. Tip: To reset the programme to the pre-rinse programme stored at the factory, use the Home Connect app or reset your appliance to the factory...
Page 22
en Additional functions Additional functions 7 Additional functions You can find an overview of the additional functions that can be selected here. Additional functions Different additional functions, which can be found on the control panel of your appliance, are available depending on the appliance configuration. You can se- lect certain additional functions depending on the programme.
Features en Symbol Additional func- tion The running time is extended. ¡ Water and energy consumption are in- ¡ creased. Depending on the appliance specifications Press in the levers on the right and Features 8 Features left on the outside of the basket. You can find an overview of the pos- Features sible features of your appliance and...
en Features 8.2 Etagere Use the cutlery shelf and space un- derneath for small cups and glasses or for large items of cutlery, e.g. cooking spoons or serving cutlery. Large plates up to a diameter of 31 cm can be arranged in the bottom basket as shown.
Features en You can fold the prongs down to po- 8.6 Cutlery drawer sition pans, bowls and glasses Arrange cutlery in the cutlery drawer. better. Folding down prongs If you do not need the prongs, fold them down. Push the lever forwards and fold down the prongs ...
en Before using for the first time Set the slider to ON or OFF. Place the glassZone in the top basket and lock in position . Push in the top basket. Check that the mounts are in the Cleaning glassZone correct position.
Water softening system en Add detergent → Page 30. Water softening system 10 Water softening sys- Start the Programme with the highest cleaning temperature without tableware. Hard water leaves limescale on the Water softening system To remove any marks from water tableware as well as the washing or other residues, we recommend tank, and parts of the appliance may you operate the appliance without...
en Water softening system The display shows H:xx. Note: Only use special salt for dishwashers. The display shows . Do not use salt tablets. Press repeatedly until the Do not use table salt. right water hardness has been set. Add the special salt to the dis- The value H:04 is set at the fact- penser.
Rinse aid system en The water hardness is 0 - 8 °E. Add rinse aid up to the max mark. ¡ You do not need to use special salt. Press . To open the basic settings, press for 3 seconds. The display shows H:xx. The display shows ...
en Detergent To save the settings, press starch and remove protein. Oxygen- for 3 seconds. based bleaching agents are generally used to remove coloured marks, e.g. tea or ketchup. 11.3 Switching the rinse aid system off Note: Follow the manufacturer's in- structions for each detergent. If you find the rinse aid refill indicator Tip: Suitable detergents are available irritating, e.g.
Detergent en With powder and liquid detergent the 12.3 Information on deter- dosage can be individually adjusted gents to the level of soiling of the table- ware. Follow the instructions on detergents For better washing and drying results in everyday use. and to avoid damage to the appli- Detergents marked as "organic"...
Page 32
en Tableware Add the detergent to the dry deter- Close the lid of the detergent dis- gent dispenser. penser. 50 ml 25 ml 15 ml If you are using tablets, one is The lid clicks into position. enough. Insert the tablets in a hori- The detergent dispenser will open zontal position.
Tableware en 13.1 Damage to glass and Cause Recommenda- tion tableware Highly caustic al- If you are using Only put glasses and china in the kaline or highly highly caustic al- dishwasher if it is marked as dish- acidic cleaning kaline or highly washer-safe by the manufacturer.
Page 34
en Tableware allowing steam to escape and water To save resources, do not pre- to leak out around the door. This rinse tableware under running wa- could damage your kitchen units. ter. Observe the following when arran- ging tableware: – Put heavily soiled tableware in the bottom basket, e.g.
Basic operation en The remaining running time of the 13.3 Removing tableware programme appears on the dis- play. WARNING Risk of injury! 14.3 Setting additional func- Hot tableware can cause burns to the tions skin. When hot, tableware is sensitive to shock, may crack and can result in You can set additional functions to injury.
en Basic operation Press . Notes If you want to add more tableware ¡ The programme is saved and the while the appliance is running, do appliance switches off. not use the tablet collecting tray as Press to resume the pro- a handle for the top basket.
Basic settings en Basic settings 15 Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings 15.1 Overview of the basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description Water hardness H:04...
Page 38
en Basic settings Basic setting Display text Selection Description Start programme SP:01 SP:00 - SP:01 Set a default programme for when the appliance is switched on. With the setting "SP:00", ¡ the last programme selec- ted is set by default when the appliance is switched With the setting "SP:01", ¡...
Basic settings en Basic setting Display text Selection Description Remote Start rc:01 rc:00 - rc:02 Activate or deactivate → "Remote Start ", Page 40. The following settings are possible: With the setting "rc:00", ¡ the function is perman- ently deactivated. With the setting "rc:01", ¡...
en Home Connect 16.2 Setting up Home Con- Home Connect 16 Home Connect nect This appliance is network-capable. Home Connect Requirements Connect your appliance to a mobile The Home Connect app has been ¡ device to control its functions via the installed on your mobile device. Home Connect app. The appliance is receiving signals ¡...
Cleaning and servicing en Note: Please note that the Requirements The appliance is connected to your Home Connect functions can only be ¡ WLAN home network. utilised with the Home Connect app. The appliance is connected to the Information on data protection can be ¡...
en Cleaning and servicing The cleaning nozzle is maintenance- 17.3 Tips on appliance care free, reducing the manual cleaning Follow the tips on appliance care to required for the filter. make sure your appliance functions The maintenance interval of the filter properly at all times. system greatly depends on the type of soiling, the detergent used and the Action...
Cleaning and servicing en Pull down the micro filter to re- Insert the filter system into the ap- move. pliance and turn the coarse filter clockwise. Make sure that the arrow mark- ‒ ings match up. Press the locking catches gether and lift the coarse filter out ...
Page 44
en Cleaning and servicing Pull up the lower spray arm to re- move. Check the outlet nozzles on the spray arms for blockages under running water and remove any for- eign bodies. Insert the lower spray arm. The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
This will avoid unneces- sary costs. Tip: You can find further information and explanations on troubleshooting on- line by scanning the QR code in the table of contents and on our website siemens-home.bsh-group.com. WARNING Risk of electric shock! Incorrect repairs are dangerous.
Page 46
en Troubleshooting Fault Cause and troubleshooting E:32-00 will light up Water tap is jammed or furred up. alternately or indicator Turn on the water tap. ▶ for water supply lights The flow rate must be at least 10 l/min when the water supply is open.
Page 47
Troubleshooting en Fault Cause and troubleshooting E:61-03 will light up Not an appliance fault. Siphon connection is still alternately. Water is closed or the wastewater hose is kinked or blocked. not drained. Check the connection to the siphon and open if ne- cessary.
Page 48
en Troubleshooting Fault Cause and troubleshooting All LEDs lit up or Electronics have detected a fault. flashing. Press the main switch button for approx. 4 seconds. The appliance is reset and restarted. If the problem occurs again: Switch off the appliance. ‒ Pull out the mains plug or switch off the fuse in ‒...
Page 49
Troubleshooting en Fault Cause and troubleshooting Remnants of food on Filters are inserted incorrectly and/or not engaged. tableware. Insert the filters properly. → "Filter system", Page 42 Engage the filters. Washing programme selected too weak. Select a more intensive washing programme. ▶ → "Programmes", Page 19 Adjust the sensitivity of the sensors.
Page 50
en Troubleshooting Fault Cause and troubleshooting Removable streaks Tableware has been precleaned too intensely. The are present on sensors chose a weaker programme. Stubborn soiling glasses, glassware cannot be entirely removed. with a metallic appear- Only remove large remnants of food and do not ▶...
Transportation, storage and disposal en Insert the pump cover and press 18.1 Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned.
en Transportation, storage and disposal 19.2 Protect appliance from 19.4 Disposing of old appli- frost ance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely.
Customer Service en The liability guarantee is valid for ¡ Customer Service 20 Customer Service the service life of the appliance. A claim can only be made under ¡ Detailed information on the warranty Customer Service the guarantee if the appliance has period and terms of warranty in your been correctly installed and con- country is available from our after-...
A detailed RED Declaration of Con- Munich, Germany. formity can be found online at The source code will be made avail- siemens-home.bsh-group.com able to you on request. among the additional documents on the product page for your appliance. Depending on the appliance specifications...
Declaration of Conformity en 2.4 GHz band (2400–2483.5 MHz): Max. 100 mW 5-GHz band (5150–5350 MHz + 5470–5725 MHz): max. 150 mW UK (NI) 5 GHz WLAN (Wi-Fi): For indoor use only. 5 GHz WLAN (Wi-Fi): For indoor use only.
Page 56
EN Manufactured by BSH Hausgeräte GmbH under the trademark licence of Siemens AG BSH Hausgeräte GmbH Carl-Wery-Straße 34 81739 München, GERMANY siemens-home.bsh-group.com *9001700408* 9001700408 (040229) 650 A1...
Need help?
Do you have a question about the iQ500 SN25HW76MM and is the answer not in the manual?
Questions and answers