GE JS630SF Quick Start Manual

JS630SF
GE Appliances 30" Slide-In Electric Range
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
RECEPTACLE LOCATIONS: Locally approved flexible service cord or
conduit must be used because terminals are not accessible after range
installation. See shaded area in drawing for location of electrical outlet box.
Recommended outlet locations allow range to be installed directly against
rear wall.
NOTE: This appliance has been approved for 0" spacing to adjacent
surfaces above the cooktop. However, a 6" minimum spacing to surfaces
less than 15" above the cooktop and adjacent cabinet is recommended to
reduce exposure to steam, grease splatter and heat.
INSTALLATION INFORMATION: Before installing, consult installation
instructions for current dimensional data and additional requirements
OPTIONAL KITS FOR SLIDE-IN ELECTRIC RANGES
WB07T10680 - Black Filler Strip Assembly
ACCESSORY BACKGUARDS
(Attaches to the back of range as a backguard when unit is
installed in 30" free-standing cutout)
JXS32SS (Stainless) - 4" High
JXS32BB (Black) - 4" High
BODY SIDES
(Slide-in ranges are sold
without sides installed. Can
be installed on either left
or right when unit has one
exposed side [no cabinet
adjacent]. Kit contains
1 body side) JXS77BB (Black)
For answers to your Monogram, GE Café
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center
KW RATING
240V 11.9
208V 8.9
BREAKER SIZE
240V 40 Amps †
208V 40 Amps †
NOTE: Check local codes
†
for required breaker size.
™ Series, GE Profile
® Service, 800.626.2000.
30"
Recommended
30"
Min.
6" Min.
Min.
Recommended
From Walls
Recommended 6" Min.
From Walls 6" Min.
NOTE: Use a 4' powercord
From Walls
to prevent interference with
Recommended
NOTE: Use a 4' powercord
the storage drawer. Power
to prevent interference with NOTE: Use a 4' powercord
cords 4-1/2' to 6' long may
From Walls
the storage drawer. Power to prevent interference with have to be dressed to allow
23-3/16"
cords 4-1/2' to 6' long may the storage drawer. Power for proper drawer closing.
NOTE: Use a 4' powercord
have to be dressed to allow cords 4-1/2' to 6' long may
23-3/16"
have to be dressed to allow to prevent interference with
for proper drawer closing.
23-3/16"
for proper drawer closing. the storage drawer. Power
cords 4-1/2' to 6' long may
have to be dressed to allow
for proper drawer closing.
2-1/2"
35-7/8"-36-1/2" from
Floor to countertop
2-1/2"
35-7/8"-36-1/2" from
2-1/2"
Floor to countertop 35-7/8"-36-1/2" from
4"
Floor to countertop
4"
35-7/8"-36-1/2" from
4"
Floor to countertop
29-15/16"-30-1/16"
29-15/16"-30-1/16"
29-15/16"-30-1/16"
Acceptable electrical
outlet area Acceptable electrical
outlet area
If you are NOT using the
Filler strip or Backguard:
If you are NOT using the
Filler strip or Backguard: If you are NOT using the
Filler strip or Backguard:
If you are NOT using the
23-3/16"
Filler strip or Backguard:
23-3/16"
23-3/16"
2-7/8"
Surface of
To Front 2-7/8"
30" Countertop
23-3/16"
Surface of To Front
30" Countertop Surface of
30" Countertop
30"
If you are using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard: If you are using the
Filler strip or Backguard:
If you are using the
25"
Filler strip or Backguard:
25"
25"
30"
25"
30"
30"
30"
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing
breakage and voiding the warranty. Make sure the wall covering, countertop, flooring and
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing
cabinets around the range can withstand the heat (up to 200°F) generated by the range.
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing
breakage and voiding the warranty. Make sure the wall covering, countertop, flooring and
A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or
breakage and voiding the warranty. Make sure the wall covering, countertop, flooring and
cabinets around the range can withstand the heat (up to 200°F) generated by the range.
metal cabinet, or allow a 24" minimum when bottom of wood or metal cabinet is protected by no
A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or cabinets around the range can withstand the heat (up to 200°F) generated by the range.
less than 1/4"-thick flame-retardant millboard covered with no less than No. 28 MSG sheet
If the countertop area is not flat, excess tension may be applied to the glass cooktop, causing
A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or
metal cabinet, or allow a 24" minimum when bottom of wood or metal cabinet is protected by no
metal (.015" thick), .015"-thick stainless steel, .025" aluminum or .020" copper.
breakage and voiding the warranty. Make sure the wall covering, countertop, flooring and
metal cabinet, or allow a 24" minimum when bottom of wood or metal cabinet is protected by no
less than 1/4"-thick flame-retardant millboard covered with no less than No. 28 MSG sheet
™ Series or B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.
cabinets around the range can withstand the heat (up to 200°F) generated by the range.
less than 1/4"-thick flame-retardant millboard covered with no less than No. 28 MSG sheet
metal (.015" thick), .015"-thick stainless steel, .025" aluminum or .020" copper.
However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent
A. Allow 30" minimum clearance between surface units and bottom of unprotected wood or
B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop. metal (.015" thick), .015"-thick stainless steel, .025" aluminum or .020" copper.
cabinetry.
metal cabinet, or allow a 24" minimum when bottom of wood or metal cabinet is protected by no
B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.
However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
less than 1/4"-thick flame-retardant millboard covered with no less than No. 28 MSG sheet
However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent
cabinetry.
clearance at the back wall.
metal (.015" thick), .015"-thick stainless steel, .025" aluminum or .020" copper.
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum cabinetry.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage
B. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
clearance at the back wall.
space above the cooktop should be avoided. If cabinet storage space is to be provided above
However, a minimum 6" spacing to surfaces less than 15" above the cooktop and adjacent
clearance at the back wall.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage
the cooktop, the risk can be reduced by installing a range hood that projects at least 5" beyond
cabinetry.
space above the cooktop should be avoided. If cabinet storage space is to be provided above To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage
the front of the cabinets.
is recommended to reduce exposure to steam, grease splatter and heat. Allow 1/4" minimum
space above the cooktop should be avoided. If cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing a range hood that projects at least 5" beyond
30"
Min.
9-1/16"
30"
9-1/16"
Min.
9-1/16"
30"
6" Min.
Min.
30"
30"
Min. If the control panel
Min.
measures 31-1/8"
1-1/4" Min. Flat 15" Min.
If the control panel (79.1 cm) like in the
30" If the control panel
measures 31-1/8" illustration AND if the
1-1/4" Min. Flat 15" Min.
Min.
(79.1 cm) like in the measures 31-1/8"
countertop has a
1-1/4" Min. Flat 15" Min.
illustration AND if the (79.1 cm) like in the
raised edge, shave
23-3/16"
countertop has a illustration AND if the raised edge to clear
25"
raised edge, shave countertop has a the control panel,
1-1/4" Min. Flat
raised edge to clear raised edge, shave as shown at left.
25"
raised edge to clear
the control panel,
25"
1-1/4" Min. from
as shown at left. the control panel,
countertop to top
as shown at left.
1-1/4" Min. from
of cabinet drawer
countertop to top 1-1/4" Min. from
of cabinet drawer countertop to top
7-1/2"
2-1/2"
of cabinet drawer
7-1/2"
7-1/2"
2-1/2"
4"
2-1/2"
7-1/2"
2-1/2"
Acceptable electrical
outlet area
2-1/2"
29-15/16"-30-1/16"
Acceptable electrical
outlet area
Accessory
Backguard JXS32
Accessory
Accessory
Backguard JXS32
Backguard JXS32
24"
2-7/8"
24"
Backguard JXS32
31-1/4"
To Front
24"
31-1/4"
24"
2-7/8"
To Front
Surface of
Countertop
20-5/8" Door
Clearance
20-5/8" Door
From Front
20-5/8" Door Clearance
Surface of
From Front Clearance
Countertop
Surface of From Front
20-5/8" Door
Countertop Surface of
Countertop
Countertop
(excluding handle)
(excluding handle)
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
9-1/16"
If the control panel
measures 31-1/8"
15" Min.
(79.1 cm) like in the
illustration AND if the
countertop has a
raised edge, shave
raised edge to clear
25"
the control panel,
as shown at left.
1-1/4" Min. from
countertop to top
of cabinet drawer
30"
4"
31-1/4"
Accessory 30"
4"
30"
4"
30"
31-1/4"
36-1/4"
36-1/4"
36-1/4"
36-1/4"
Clearance
From Front
Surface of
25-3/4"*
(excluding handle)
25-3/4"*
25-3/4"*
*Total depth from wall to
front of closed oven door
*Total depth from wall to including handle is 28-1/2"
25-3/4"*
*Total depth from wall to
front of closed oven door
(excluding handle)
including handle is 28-1/2" front of closed oven door
including handle is 28-1/2"
*Total depth from wall
front of closed oven do
including handle is 28
Specification Revised 1/16