Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Flint nyloflex Round Brush Washer F III
- Page 1 Pre-installation Guide nyloflex® Round Brush Washer F III IMPORTANT! Please follow the instructions in this guide when preparing the installation site prior to arrival and installation of the equipment December 8th, 2017 Edition AA, Part No 10087067 English (en-us) Original version...
-
Page 2: About This Manual
About this manual About this manual This manual applies to the Flexo Processor nyloflex® Round Brush Washer F III. This manual is published by: Glunz & Jensen A/S Selandia Park 1 4100 Ringsted Denmark Phone: +45 57 68 81 81 E-mail: gjhq@glunz-jensen.com Internet: www.glunz-jensen.com Copyright ©... -
Page 3: Table Of Contents
Table of Contents Table of Contents About this manual Table of Contents Introduction Reservations Introduction Notes, Cautions and Warnings! Transportation When the nyloflex® Round Brush Washer arrives Storing of the equipment prior to the installation The crate Crate Dimensions nyloflex® Round Brush Washer Weight Checking the crate for damage Handling the crate... -
Page 4: Introduction
Introduction Introduction Reservations • This manual was written and illustrated using the best possible information available at the time of publication. • Any differences between this manual and the equipment reflect improvements introduced after the publication of the manual. • Changes, technical inaccuracies and typographic errors will be corrected in subsequent editions. -
Page 5: Notes, Cautions And Warnings
Introduction Notes, Cautions and Warnings! Notes, cautions, and warnings in this manual are used and categorized as described below: Symbol Meaning Explanation The operator should observe and/or act according to the information in order to obtain the best possible function of the equipment. NOTE The operator must observe and/or act according to the information in order to avoid any mechanical or electrical damage to the equipment. - Page 6 December, 2017 Pre-installation Guide nyloflex® Round Brush Washer F III...
-
Page 7: Transportation
Transportation Transportation When the nyloflex® Round Brush Washer arrives Storing of the equipment prior to the installation The equipment will usually be delivered some time before the arrival of the service technician. Provide for an appropriate place indoor to store the crated equipment until the service technician arrives. The crate Crate Dimensions nyloflex®... -
Page 8: Weight
Transportation Weight F III With crate 1400 kg (3100 lbs) Without crate 1100 kg (2400 lbs) Checking the crate for damage Check if the crate is damaged on delivery at the customer's address. Make notes of any damages, before opening the crate. Provide a detailed description and take a photograph of the damage. Report any damage of the crate to the shipping company and notify the insurance agent, if appropriate, before the mishandled package is opened. -
Page 9: Lifting The Crate
Transportation Lifting the crate The equipment is supplied in a wooden crate on a pallet. A fork-lift truck is required for lifting the crate on arrival and for lifting the equipment off the pallet. WARNING: The equipment is very heavy equipment. It is only possible to lift the equipment off the pallet using a forklift truck or a pallet mover. - Page 10 December, 2017 Pre-installation Guide nyloflex® Round Brush Washer F III...
-
Page 11: Installation Requirements
Installation requirements 3-11 Installation requirements WARNING: The equipment must be installed in restricted access locations only. NOTE: Check the delivery route to the installation location for necessary clearance and remove all obstructions. Heating and ventilation Provide a heat and ventilation system capable of maintaining room temperature between 17°C (63°F) and 28°C (82°F) and a relative humidity (non condensing) of min. -
Page 12: Dimensions And Connections
Installation requirements 3-12 Dimensions and connections December, 2017 Pre-installation Guide nyloflex® Round Brush Washer F III... -
Page 13: Compressed Air
Installation requirements 3-13 Compressed air Description F III Min. pressure 6 bar (87 psi) Max. pressure 10 bar (145 psi) Volume Hose size ø 6 mm Solvent connection If the solvent barrels are more than 5 meters from the processor and the piping is lifted higher that the solvent tanks, it is recommended to mount a non-return valve at the barrels to prevent backlash of solvent or air in the hoses during process. -
Page 14: Electrical Requirements
Installation requirements 3-14 Electrical requirements WARNING: Electrical installation must conform to local regulations and guidelines. Main power outlet Provide an mains power-outlet with an electrical plug lockout close to the installation site. The table showing "Power supply requirements" on the facing page indicates the applicable power supply types. Power cable NOTE: The cable for the main power connection is included with the equipment. -
Page 15: Electrical Specifications
Installation requirements 3-15 Electrical specifications Power supply requirements CAUTION: The requirements below are specifications for preparing the installation protection. The fuses/circuit breakers must be prepared according to local regulations, and with adequate capacity as specified here. The circuit breakers must be suitable for inventor operation. NOTE: Specifications on the equipment's name plate is the actual input current and will thus not be identical to below mentioned. - Page 16 December, 2017 Pre-installation Guide nyloflex® Round Brush Washer F III...
-
Page 17: Checklist
Checklist 4-17 Checklist Please check the following conditions in order to ensure a trouble-free installation of the equipment: Delivery of the crate and transport to the installation site Is there a place indoor where the crated equipment can be stored temporarily? Is there a hand-powered pallet mover, a fork-lift truck or any other lifting device available? Please refer to "Lifting the crate"... - Page 18 Checklist 4-18 Is solvent connection available according to the requirements as described in chapter "Solvent connection" on page 13. Availability of warm water for cleaning of the equipment? Is the tap water temperature adjustable? Is the supply water pressure min. 6 bar (87 psi)? December, 2017 Pre-installation Guide nyloflex®...
Need help?
Do you have a question about the nyloflex Round Brush Washer F III and is the answer not in the manual?
Questions and answers