Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for TAIYO SEIKI COM JEZ II Series
- Page 1 User's Manual TAIYO SEIKI CO., LTD.
-
Page 3: Table Of Contents
1. Table of contents Table of contents 1. Table of contents ............................1 2. Introduction .............................. 2 2-1. Safety precautions ..........................2 2-2. Notes on use ............................3 3. Components enclosed in the storage case ....................4 4. Name of each part ............................ 4 5. -
Page 4: Introduction
2. Introduction Prior to installation, operation, maintenance, and inspections, please read the user's manual carefully to ensure proper use and maintenance of the machine. Please ensure that you have a good understanding of all the information and important safety points. It is also a good idea to store the user’s manual near the machine for quick reference. -
Page 5: Notes On Use
2-2. Notes on use ・ Do not use any tape that is not the specified tape for this machine, as it could potentially damage the machine or make it inoperable. ・ Use only the power sources indicated on the main unit, and operate the machine only in a location where there are few voltage fluctuations. -
Page 6: Components Enclosed In The Storage Case
3. Components enclosed in the storage case Main machine unit···································· 1 Attachments A ········································· 1 Board to adjust the position of the band when performing banding. Attachments B ········································· 1 Board to adjust the position of the band when performing banding. Knob bolts for attachments ························... -
Page 7: Instructions For Use
5. Instructions for use 5-1. Content and usage rules for the switch box Used to power up the manual banding operation. ・START switch Illuminated during the banding operation; blinking when the front door is START lamp opened. Changes between manual and automatic operation. ・AUTO switch Goes off during manual operation mode;... -
Page 8: Preparing For Operation
5-2. Preparing for operation ① Plug the power cord into the right side of the machine, and turn the power switch ON after plugging the power plug into the outlet. ② The POWER lamp flashes and the current temperature is shown on the display. When the status of POWER lamp changes from flashing to lit, the preparation for operation is complete and the machine is ready for use. -
Page 9: 5-3.Tape Setting
5-3.Tape setting ① Open the front door. (When the power is switched on, the START and POWER lamp flash). ② Pull out the tape reel cover to the front. ③ Place a tape on the paper tube holder. *Be careful with the direction of the tape. - Page 10 ④ Draw the tape and hook it to the tape roller. ⑤ Insert the tape end into the tape guide, pass the tape until it touches the rubber roller, then lightly put a hand on the arrow, and hold the tape. Press the tape setting switch.
-
Page 11: Manual Operation
5-4. Manual operation Manual operation refers to using the START switch of the operation switch to perform banding. ・Manual operation procedure ① Place the product on top of the table and check the position of the band. ② Once the START switch is pressed, the tape is tightened, glued, and cut, and banding is completed. -
Page 12: Automatic Operation
5-5. Automatic operation Automatic operation refers to the performing of banding automatically via detection of an object using the product sensor. Without using the START switch. ・Automatic operation procedure ① Press the AUTO switch of the control switch. ② The AUTO lamp will turn ON. (Automatic operation mode will be in effect as long as the AUTO lamp stays ON.) ③... -
Page 13: Settings And How To Change
6. Settings and how to change 6-1. Settings and switching display In main mode, press the MODE switch each time, the display changes as follows. Main mode = Display for current temperature and setting value confirmation Setting mode = Setting value change mode for each setting item How to check the settings and switch the display (Main mode) ①... -
Page 14: How To Switching The Mode
6-2. How to switching the mode How to check the current mode Main mode : Banding operation possible mode POWER lamp flashes or lights. AUTO lamp flashes or lights. (Lights when selected AUTO mode) Change the setting mode : Mode for changing the setting value for each. All blinking AUTO, START, POWER lamps. -
Page 15: Change The Heater Temperature Setting : Display Section "C-St
6-3. Change the heater temperature setting : Display section "C-st" Setting range : 150℃～220℃ Initial value : 160℃ When the tape adhesion is poor, change the temperature setting of the heater. ① Use the UP (∧) and DOWN (∨) switches to change the display to "C-st". ②... -
Page 16: Change The Tightening Mode: Display "Tp-S
6-4. Change the tightening mode: Display "tP-S" Setting range : "trq" or "PLS" Initial value : trq There are two types of tightening modes. When the display shows "trq", it is called "tightening torque". When it shows "PLS", it is called "tightening pulse". ①... -
Page 17: Change The Tightening Torque Setting Value：display "Trq
6-5. Change the tightening torque setting value：Display "trq" Setting range : 1P～100P Initial value : 30P The tightening torque is; If the tightening power is weakened, the speed at which the tape is wound will decrease, but the product will be bound more softly. If you increase the tightening power, the tape winding speed will increase and the tightening power will become stronger, making it possible to create a hard band on the product. -
Page 18: Change The Tightening Pulse Setting Value：display "Pls
6-6. Change the tightening pulse setting value：Display "PLS" Setting range : 1000~5500 Initial value : 3000 The tightening pulse is; Tightening can be done according to the outer circumference of the product. Even if you tighten the tape less or more, the speed and power with which you wind the tape will not change. -
Page 19: Change The Tape Feeding Point : Display "Feed
6-7. Change the tape feeding point : Display "FEEd" Setting range : P-1~P-6 Initial value : P-3 The tape feeding point is; This is to determine the amount of tape feed when the tape is set in the arch guide. Select the tape feeding point (tape feeding amount) that is preset on the servo motor. -
Page 20: About Bundle Counter
6-8. About bundle counter The bundle counter counts from 1 to 9999. When it reaches 10000 times, it will be automatically reset to 0. *If you press and hold the mode switch for 3 seconds when the display shows the band counter, the current counter will be reset to 0. -
Page 21: Setting Mode List
7. Setting mode list *Attention The settings in red letters can be changed by turning ON dip switch No. 6 on the board. However, there is no need to change it for normal use. Do not change that parts in red letters as this may cause malfunction. -
Page 22: Problem Display, Error Indicators
8. Problem display, error indicators *If a problem occurs, a problem number is displayed. Identify the issue, turn off the power, unplug the machine from the electrical outlet, and contact the store. Unauthorized work on the machine will void the warrantee. Problem error indicator numbers Error Issue... -
Page 23: About Setting Data Abnormality
9. About setting data abnormality Err.3 is a specification that automatically overwrites the initial value. If Err.3 occurs even after turning the main power OFF to ON after Err.3 occurs, please refer to the steps below to initialize the setting data. *If the setting data has been changed, the setting data will be returned to the factory state. -
Page 24: Specifications
10. Specifications ■Machine performance Banding capacity Model Measurements of objects that can be bound (minutes) Maximum (width 150mm , height 100mm) JEZⅡ-150 24 times Minimum (width 30mm , height 5mm) Maximum (width 300mm , height 200mm) JEZⅡ-300 22 times Minimum (width 30mm , height 5mm) Maximum (width 400mm , height 200mm) JEZⅡ-400 20 times... - Page 25 Taiyo Seiki Co., Ltd.'s instructions or authorized agent or employees of Taiyo Seiki Co., Ltd. The provisions of the warranty are the sole obligations of Taiyo Seiki Co., Ltd. and exclude all other warranties expressed or implied, including any warranties of merchantability. There are no warranties which extend beyond this warranty.
- Page 27 Head Office: 4-3-7, Hino, Daitoh, Osaka, 574-0062, Japan. Phone: 81-72-873-3739 Fax: 81-72-875-4324 U R L: http://www.com-machine.co.jp E-mail: taiyo@com-machine.co.jp 4-240419...
Need help?
Do you have a question about the COM JEZ II Series and is the answer not in the manual?
Questions and answers