1. Manuals
  2. Brands
  3. Harbor Freight Tools Manuals
  4. Grinder
  5. Bauer 1865E-B
  6. Owner's manual & safety instructions

Harbor Freight Tools Bauer 1865E-B Owner's Manual & Safety Instructions

4-1/2"
Hide thumbs

Advertisement

Table of Contents

Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
4-1/2"
ANGLE GRINDER
email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1‑888‑866‑5797 as soon as possible.
©
Copyright
2024 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
1865E-B
tM
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
24e
64856

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Bauer 1865E-B and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Harbor Freight Tools Bauer 1865E-B

Summary of Contents for Harbor Freight Tools Bauer 1865E-B

  • Page 1 No portion of this manual or any artwork contained herein may be reproduced in Failure to do so can result in serious injury. any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing SAVE THIS MANUAL.

  • Page 2: Table Of Contents

    table of contents Safety ............2 Operation ........... 12 Specifications ..........10 Maintenance ..........14 Setup ............10 Warranty ............ 16 WarninG SyMBOLS anD DeFinitiOnS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

  • Page 3: Safety

    electrical Safety 1. power tool plugs must match the outlet. 4. Do not abuse the cord. never use the cord never modify the plug in any way. for carrying, pulling or unplugging the power Do not use any adapter plugs with grounded tool.
  • Page 4 These carry important safety information. replacement parts. This will ensure that the If unreadable or missing, contact safety of the power tool is maintained. Harbor Freight Tools for a replacement. Page 4 For technical questions, please call 1-888-866-5797. Item 64856...
  • Page 5 Safety Warnings common for Grinding, Wire Brushing, or abrasive cutting-off Operations 1. this power tool is intended to function as a be capable of stopping flying debris generated by grinder, wire brush, or cut-off tool. read all various operations. The dust mask or respirator safety warnings, instructions, illustrations and must be capable of filtering out particles generated specifications provided with this power tool.
  • Page 6 Kickback and related Warnings Kickback is a sudden reaction to a pinched or 1. Maintain a firm grip on the power tool and snagged rotating wheel, backing pad, brush position your body and arm to allow you to or any other accessory. Pinching or snagging resist kickback forces.
  • Page 7 Safety Warnings Specific for abrasive cutting-off Operations 1. Do not “jam” the cut-off wheel or apply 4. Do not restart the cutting operation in excessive pressure. Do not attempt to make the workpiece. Let the wheel reach full an excessive depth of cut. Overstressing the speed and carefully reenter the cut.
  • Page 8 Grounding tO preVent eLectric SHOcK anD DeatH FrOM incOrrect GrOunDinG Wire cOnnectiOn: check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. never remove the grounding prong from the plug.
  • Page 9 extension cords 1. Grounded tools require a three wire extension cord. 7. Make sure the extension cord is properly wired Double Insulated tools can use either and in good electrical condition. Always replace a two or three wire extension cord. a damaged extension cord or have it repaired by a qualified electrician before using it.

  • Page 10: Specifications

    Specifications Electrical Rating 120V ~ / 60Hz / 7A No Load Speed : 11000/min Arbor Hole Diameter 7/8″ Spindle Thread 5/8″ - 11  U NC Wheel Diameter 4-1/2″ (Ø115mm) Setup - Before use: read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
  • Page 11 installing the auxiliary Handle tO preVent SeriOuS inJury: Do not operate this tool with one hand only or without the auxiliary Handle properly installed. Handle alternate location 1. The Auxiliary Handle may be installed on either side of the Gear Housing. 2.

  • Page 12: Operation

    Operating instructions read the entire iMpOrtant SaFety inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. tool Set up tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: Make sure that the power Switch/trigger is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section.
  • Page 13 Workpiece and Work area Set up 1. Designate a work area that is clean and well‑lit. 3. Secure loose workpieces using a vise or clamps The work area must not allow access by children (not included) to prevent movement while working. or pets to prevent distraction and injury.

  • Page 14: Maintenance

    Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. tO preVent SeriOuS inJury FrOM acciDentaL OperatiOn: Make sure that the power Switch/trigger is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section. tO preVent SeriOuS inJury FrOM tOOL FaiLure: Do not use damaged equipment.
  • Page 15 troubleshooting problem possible causes Likely Solutions Tool will not start. 1. Cord not connected. 1. Check that cord is plugged in. 2. No power at outlet. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.

  • Page 16: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

This manual is also suitable for:

64856

Table of Contents