Advertisement
Advertisement
Table of Contents
Summary of Contents for IES IES-BATT-14.33
-
Page 2: Switch On/Off
Brief lntroduction Interface Introduction 2.2.1 Switch ON / OFF 2.2.2 LED Indicator Definition 2.2.3 CAN / RS485 Port 2.2.4 RS232 Port Checking Before Installation 3.1.1 Checking Outer Packing Materials 3.1.2 Checking Deliverables Tools Installation Requirements 3.3.1 Installation Environment Requirements 3.3.2 Installation Carrier Requirements Installation Instructions 3.4.1... - Page 3 PACK: UN38.3, IEC 62619, IEC61000 CELL: UN38.3, IEC62619, UL1642, JET (more available upon request) IES-BATT-14.33 Battery Product Ordering Part IES-BATT-14.33 Parallel cable IES-BATT-14.33 to PCS cable 3. Please refer to the Warranty Letter for applicable conditions, the warranty is due whichever comes first.
-
Page 4: Operation Interface Description
1.Switch ON IES-BATT-14.33 has built-in BMS (Battery Management System), which can manage and For a single IES-BATT-14.33, firstly, the Air switch (9), Slide switch (5) and POWER (3) are monitor cells information including voltage, current and temperature. Besides that, BMS can in the ON state, then long press (over 3 seconds) SW (6), LED will flash, and the battery will balance cells charging to extend cycle life. -
Page 5: Switch Off
For a single IES-BATT-14.33, switch OFF POWER (3) and Air switch (9). For multiple IES-BATT-14.33 in parallel, switch OFF POWER (3) and Air switch (9) on all slave batteries first. Then switch OFF POWER (3) and Air switch (9) on the Master battery. - Page 6 CAN / RS485 Communication Terminal (RJ45 port), connects to inverter, and follows CAN / RS485 protocol. RS232 Communication Terminal (RJ45 port) follows RS232 protocol, for manufacturers or professional engineers to debug or service. Install the Upper Cover...
-
Page 7: Installation Environment Requirements
Wall bracket Wooden box Pearl wool Upper cover Battery Pearl wool Installation Requirements Installation Environment Requirements Upper cover • Install the battery in the indoor environment. • Place the battery in a secure location away from children and animals. • Do not place the battery near any heat sources and avoid sparks. •... - Page 8 Drill the hole with a 12mm drill bit as follows and fix the wall bracket to the wall. M10*80 M10*80 Wall mounted Floor stand hole location hole location ≥ The bearing capacity of the wall is greater than 145kg 800mm 250mm 298.5mm Use a crane to lift the ring on the battery pack and attach it to the wall bracket.
- Page 9 Connect to the ground. Connect the communication cable. Link In to PCS CAN port Link Out RS232 WIFI Link In POERT Link Out RS232 Connect the power cable. Note that all switches are OFF before wiring. Air Switch to PCS B- to PCS B+...
- Page 10 When multiple batteries are connected in parallel, follow the following wiring mode. Parallel cables' length is 1200mm; power cables' leghth is 1700mm. Scheme One Scheme Two Link In Link In Link In Link In Link In Link In to PCS CAN port to PCS CAN port Link Out RS232 Link Out RS232...
- Page 11 Install the upper cover. Upper cover card slot direction Battery should be stored in an environment with temperature range between -10°C ~ +45°C, and maintained regularly according to the following table with 0.5C (140 A) current till 40%SOC after a long storage time. Recharge Conditions When in Storage The over-discharged (90% DoD) battery should be recharged according to the following table, otherwise the over-discharged battery wil be damaged.
Need help?
Do you have a question about the IES-BATT-14.33 and is the answer not in the manual?
Questions and answers