Advertisement
Advertisement
Table of Contents
Summary of Contents for Ardisam NESTED Z8
- Page 1 Hang-On Stand MODEL NT101 MAXIMUM FIELD RATING 350 LB. TREE DIAMETER RANGE 8" TO 20" WEAR YOUR HARNESS! PRODUCT MEETS INDUSTRY STANDARDS RECOGNIZED BY © 2024 Ardisam, Inc. | All Rights Reserved P/N: 44525 C/N: 45965 REV2: 01/22/24 PARTICIPATING MEMBER...
-
Page 2: Table Of Contents
Limited Lifetime Warranty. All other implied warranties are excluded. Liability for incidental or consequential damages are excluded to the extent exclusion is permitted by law. Ardisam, Inc. does not assume and does not authorize any other person to assume for us, any liability in connection with the sale of our products. Ardisam, Inc. retains the right to change models, specifications, and price without notice. -
Page 3: Warnings
READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE ASSEMBLY STOP MODEL NT101 WARNING ALWAYS inform someone of the hunting location, MAXIMUM OCCUPANCY - ONE (1) where the treestand will be located and the expected TOTAL WEIGHT LIMIT - 350 LB duration of the hunt. TREE DIAMETER RANGE - 8"... - Page 4 WARNING INSPECTION AND MAINTENANCE ALWAYS maintain three (3) points of contact when BEFORE EACH USE PERFORM THE FOLLOWING: climbing a ladder treestand or hang-on stand. Proper three-point contact means having either two feet with • Inspect all webbing, rope, cord, and strap assemblies for one hand or one foot with two hands on the step wear or damage.
-
Page 5: Use Instructions
USE INSTRUCTIONS This treestand includes leveling features which allow the SEAT ANGLE ADJUSTMENT user to level the seat and platform. Follow the instructions below and become familiar with these features at ground Like the platform, the seat angle can also be adjusted to level before using before using. - Page 6 USE INSTRUCTIONS SIDE TO SIDE LEVELING INSTRUCTIONS SEAT PAD INSTRUCTIONS To adjust the treestand side to side, during initial To attach the seat pad to the seat frame: installation to the tree, simply pivot the treestand to the 1. Attach to the front of the frame using the two hook/ left or right on the bottom tree blade and position the top loop straps (SEE FIGURE 6).
-
Page 7: Warnings
ASSEMBLY INSTRUCTIONS READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE SETUP & USE STOP WARNING WARNING Double check assembly steps to be certain you have DO NOT twist strap when attaching. See setup and correctly assembled this product. use instructions for correct attachment. Practice installing, adjusting and using your treestand ALWAYS climb tree on the attachment side of this at ground level prior to using it at elevated positions. -
Page 8: Set-Up And Use Instructions
SET-UP AND USE INSTRUCTIONS During installation and removal of a hang-on treestand, you must always and properly use the included Full Body Harness (Fall Arrest System) with climbing belt. Refer to the Full Body Harness and climbing belt instructions included with this product for proper use. You must always use the Full Body Harness while using this product. - Page 9 ASSEMBLY INSTRUCTIONS WARNING DO NOT install the bottom strap with platform folded ELASTIC PRE-SET STRAP up to avoid damaging your treestand! While pivoting the platform down at any time, do not force it. Adjust the position of the treestand on the tree or the tension in the straps until it can be levered into place easily and securely.
-
Page 10: Illustrated Parts Breakdown
ILLUSTRATED PARTS BREAKDOWN *SEE TORQUE AND THREAD LOCKER SPECIFICATION TABLE... -
Page 11: Parts List
PARTS LIST TORQUE AND THREAD LOCKER SPECIFICATIONS ITEM # PART # DESCRIPTION QTY. 40785 TOP TREE BLADE ITEM # PART # TORQUE THREAD LOCKER (Nm) 41850 BLACK CABLE 2-5/8 IN *APPLY MEDIUM STRENGTH, BLUE THREAD LOCKER WHEN 43658 43586 SPACER 7 X 20 X 6 MM SERVICING OR REASSEMBLING THESE BOLTS 43587... - Page 12 RIVERS EDGE TREESTANDS, A DIVISION OF ARDISAM, INC. ® 1730 Industrial Avenue, PO Box 666, Cumberland, WI 54829 Phone: 800-345-6007 | Fax: 715-822-2124 All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvement, product images may not be exact.
Need help?
Do you have a question about the NESTED Z8 and is the answer not in the manual?
Questions and answers