nvent TB430C Instruction Sheet

INSTRUCTION SHEET


TB CENTER
TB BRACKET
PLATE
TB914HD OR
TB1624HD
TB430C OR
TB430CFB(RED)
TB1624HD
TB914HD OR
TB1624HD
AS SHIPPED
9" - 17" SPAN,
UL514A IN-WALL
FIXTURE/LUMINAIRE
APPLICATION
(4) #8 SELF-DRILLING
SCREWS (2 PER STUD
AS SHOWN)
WARNING:
1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at
www.nVent.com and from your nVent customer service representative.
2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property
damage, serious bodily injury and/or death, and void your warranty.
5. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
6. All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified
engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are
owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the
right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.nVent.com
SPAN BETWEEN
UL514A LOAD RATING
(2) STUDS
10 LBS IN-WALL
FIXTURE/LUMINAIRE
9" - 17" SPAN
50 LBS OVERHEAD CEILING
FIXTURE/LUMINAIRE
10 LBS IN-WALL
FIXTURE/LUMINAIRE;
OVER 17" - 25"
SPAN
50 LBS OVERHEAD CEILING
FIXTURE/LUMINAIRE
50 LBS T-GRID CEILING
9" - 25" SPAN
FIXTURE/LUMINAIRE
BOX VOLUME;
33.5 CU. IN. MIN. at fully extracted position -
45.5 CU. IN. MAX. at fully extended position
(2) BOX DEPTH ADJUSTMENT SCREWS;
Work screws back and forth to adjust
and avoid overtightening which can
cause screws to strip
"Secure free end of
ground wire to
device/fixture ground
terminal"
89231127_A
PAGE
PAGE 1
PAGE 2
PAGES 2 & 3
PAGES 2 & 3
PAGES 3 & 4
ADJUSTABLE FROM
0.55" - 1 1/2" DEPTH
FM4;
SOLD SEPARATELY
1 OF 4
© 2023 nVent All Rights Reserved
12 GAUGE
TB430CRAIL TBTG
DROP WIRE
NONE NONE NONE
NONE NONE NONE
(2) NONE NONE
(2) NONE NONE
NONE (2) (1)
TB430C
OR
TB430CFB
ADJUSTMENT
RANGE
0.55" - 1 1/2"
DEPTH
TB914HD OR
TB1624HD;
SOLD
SEPARATELY
(2) #8 SELF-DRILLING
SCREWS
(1 TOP; 1 BOTTOM
AS SHOWN)