Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Wegener Autotherm3
- Page 1 Autotherm3 Hot Gas Welder...
- Page 2 Autotherm3 OPERATING INSTRUCTIONS HOT GAS WELDER AUTOTHERM 3 Provided by: Wegener International GmbH Ernst-Abbe-Str. 30 D-52249 Eschweiler +49 2403 70484-0 +49 2403 70484-99 info@wegenerwelding.de V2.3...
-
Page 3: Table Of Contents
Autotherm3 Table of contents EC - Declaration of Conformity Safety instructions Description of the device Air supply Operating the device Switching on Temperature adjustment Lack of air Switching off Display Celsius/Fahrenheit Setup Changing the nozzle Warning notices Faults Maintenance Replacing the heating element... -
Page 4: Ec - Declaration Of Conformity
Autotherm3 EC - Declaration of Conformity We, Company Wegener International GmbH, Ernst-Abbe-Str. 30, 52249 Eschweiler declare within the meaning of the EC - rules 2014/35/EU, Niederspannungsrichtlinie 2014/30/EU, EMV-Richtlinie that the product Device designation Hot Gas Welder Type: Autotherm3 to what this declaration refers, confirms with the following EC –... -
Page 5: Safety Instructions
Autotherm3 CORRECT USE WEGENER Autotherm3 may only be used for its intended purpose as described in these operating instructions. Any other use will be deemed to be not in accordance with its intended use. The manufacturer cannot be held liable for any resulting damages. -
Page 6: Description Of The Device
Ensure an air supply of 60 l/min (±15 l/min) HINT: for a perfect operation of the Autotherm3! Operating the device The air supply must be maintained for at least 3 min. after the power is switched off to prevent the device from overheating. -
Page 7: Switching On
Autotherm3 Before switching the device on, make sure that the air supply (recommended value: 60 l/min.) has been provided. After plug in the main, the current heating element temperature and "off" appear alternately in the LCD display. You can now call the following functions with the push buttons: Switching on Keep the right key pressed for a moment. -
Page 8: Switching Off
Autotherm3 Switching off The device can be switched off by either unplugging from the mains or by pressing the left key for a moment ("set" appears, followed by "off"). All values that were last set will be saved. It has to be ensured that the air supply keeps connected during cooling down the device. -
Page 9: Setup
The use of an air flow sensor is urgently recommended (WEGENER air flow sensor with WEG 06f controller). Do not operate the device without air supply. -
Page 10: Warning Notices
Autotherm3 Warning notices The burner pipe can become very hot during operation even when used correctly! Risk of burns! The air escaping from the welder can reach a temperature of several hundreds of degrees Celsius so that you must take great care when working with the device, storage during use and servicing work so as to avoid any accidents. -
Page 11: Faults
Autotherm3 Faults The following list should make it easier for you to find and remedy the cause of faults: Fault Cause Remedy Air/power switched off Switch on device Device not switched on Switch on does Power supply defective Check Incorrect quantity of air (Error... -
Page 12: Maintenance
Autotherm3 Maintenance Keep the device clean, to extend the lifetime. Please make sure that repairs on your own will exclusively be realized by authorized personnel and using original WEGENER spare parts. Replacing the heating element Assembly work may only be carried out after the... -
Page 13: Warranty
Autotherm3 Installation: Push the thermal sensor through the round bore of the element Align and screw the element tight. Do not bend the photodiode! Disconnect the feed line Bend the thermal sensor carefully (see top photo). Re-insert the complete unit into the handle... -
Page 14: Technical Data
Autotherm3 Technical data Name: Hot gas welder Type: Autotherm3 Serial number: ____________ Tested by: ____________ Models 230V: #25550 #25551 Hose length: Mass (incl. hose) approx.: 1.3 kg 2.0 kg Nozzle adapter: M 10 M 10 Heating capacity: 1000 W 1000 W... -
Page 15: Spare Parts And Accessories
Autotherm3 Spare parts and accessories Our complete range of nozzles you find on our website www.wegenerwelding.de => products => welding => hot air welding => welding nozzles. Also there is the possibility for customized nozzles. Ask us for information about customized nozzles.
Need help?
Do you have a question about the Autotherm3 and is the answer not in the manual?
Questions and answers