Subscribe to Our Youtube Channel
Summary of Contents for Shark LH240-1
- Page 1 SHARK LH240 -1 Spreader on remote control Operating and Installation Instructions NOTICE Read this manual before installing and operating the spreader.
-
Page 2: Table Of Contents
Table of Contents SAFETY INFORMATION ..................1 SAFETY ..........................1 WARNING/SAFETY LABELS ..................1 SAFETY MEASURES ....................... 2 PERSONAL SAFETY ......................2 FILLING OF THE SPREADER ................3 EXPERT ASSEMBLY ....................... 3 APPROXIMATE MATERIAL WEIGHTS ................ 3 INSTALLATION OF THE SPREADER ..............4 INSTALLATION PROCEDURE .................. -
Page 3: Safety Information
SAFETY INFORMATION SAFETY INFORMATION SAFETY COMMENT: WARNING The word "NOTE" in this manual will alert you to key information or instructions. Indicates a potential hazard that could lead to WARNING/SAFETY LABELS serious injury or death. Read and understand the warning and warning labels on the spreader. -
Page 4: Personal Safety
SAFETY INFORMATION SECURITY MEASURES Improper installation and operation can lead to personal injury and damage to equipment and NOTICE property. Read and understand the warning labels and Before putting the spreader into operation, operating instructions before installing and operating the dismantled parts and connecting parts the spreader. -
Page 5: Filling Of The Spreader
FILLING OF THE SPREADER FILLING OF THE SPREADER APPROXIMATE WEIGHTS OF THE This guide contains recommended MATERIAL vehicles for spreader transport. WARNING EXPERT ASSEMBLY Overloading can cause an accident or damage. WARNING Do not exceed the values shown on the vehicle's GVWR or GAWR label. -
Page 6: Installation Of The Spreader
INSTALLATION OF THE SPREADER INSTALLATION OF THE SPREADER 2. Using the six supplied flange bolts and four supplied self-locking nuts, mount the INSTALLATION PROCEDURE support frame to the drive assembly. Tighten the bolts and nuts. Install the spreader as instructed. Contact a qualified workshop and have the spreader fitted there. -
Page 7: Mounting On The Towing Bracket
INSTALLATION OF THE SPREADER MOUNTING ON THE TOWING NOTICE BRACKET Before drilling, check that the vehicle wiring or other parts have not been damaged. NOTICE 4. Drill four holes in the hopper with the Hold the spreader firmly when disassembling or support hole as a template. -
Page 8: Spreader Operator
SPREADER OPERATOR SPREADER OPERATOR Tips for your ride: RIDING AND GRITTING ON SNOW AND ICE Drive defensively. WARNING Do not drive or operate the spreader after having consumed alcohol. Driving under the influence of alcohol is very dangerous. Even small amounts of alcohol can ... -
Page 9: Connection Of The Spreader Power Supply
SPREADER OPERATOR STARTING AND STOPPING THE WARNING ENGINE Do not use the device under the influence of alcohol, drugs or medication that may affect To start the spreader, press the "A" or "B" judgment and reaction time. button on the controller. "A" means fast, WARNING "B"... -
Page 10: Dismantling The Spreader
SPREADER OPERATOR DISMANTLING THE SPREADER TIPS FOR WORKING WITH A NOTICE SPREADER Empty the hopper before dismantling the spreader. Do not exceed a speed of 16 km/h while spreading. NOTICE If the passage is difficult, drive slowly. Hold the spreader firmly when disassembling or assembling to prevent it from falling. -
Page 11: Programming And Pairing Of The Remote Control
REMOTE CONTROL If any of the buttons do not work, go to "Resetting PROGRAMMING AND PAIRING THE the Remote Control Module" and repeat the REMOTE CONTROL programming and pairing process. Resetting the remote receiving module Switch the three-position switch to the "LEARN MODE"... -
Page 12: Maintenance
MAINTENANCE Apply a small amount of fine oil to the latch as needed. MAINTENANCE WARNING Never remove the spreader with material in the AFTER EACH USE hopper. NOTICE Do not leave unused material in the hopper. NOTICE Materials will freeze or solidify, causing the unit to Disconnect power from the spreader's electrical not function normally. - Page 13 Official distributor: ASP Group s.r.o. Address: Staroplzenecká 290, 326 00 Letkov Česká republika E-mail: info@aspgroup.cz Tel: +420 378 21 21 21 www.aspgroup.eu Copyright © 2023 ASP Group Distributing www.shark-accessories.eu...
Need help?
Do you have a question about the LH240-1 and is the answer not in the manual?
Questions and answers