Advertisement
Quick Links
FCC
Federal Communications Commission (FCC) Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should
be installed and operated with minimum distance 20cm between the radiator and your body.
WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES:
EXERCISE EXTREME CAUTION WHEN USING Z-Wave® DEVICES TO CONTROL APPLIANCES. OPERATION OF THE Z-Wave® DEVICE MAY BE IN A DIFFERENT ROOM THAN THE CONTROLLED
APPLIANCE, ALSO ANUNINTENTIONAL ACTIVATION MAY OCCUR IF THE WRONG BUTTON ON THE REMOTE IS PRESSED. Z-Wave® DEVICES MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED
EVENT PROGRAMMING. DEPENDING UPON THE APPLIANCE, THESE UNATTENDED OR UNINTENTIONAL OPERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS CONDITION. FOR THESE
REASONS, WE RECOMMEND DO NOT RETURN THIS PRODUCT TO THE STORE THE FOLLOWING: DO NOT USE Z-Wave® DEVICES TO CONTROL ELECTRIC HEATERS OR ANY OTHER APPLIANCES
WHICH MAY PRESENT A HAZARDOUS CONDITION DUE TO UNATTENDED OR UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL.
ZW39SU User Manual
Plug-in Dimmer User Manual
Advertisement
Summary of Contents for Z-Wave Alliance ZW39SU
- Page 1 ZW39SU User Manual Plug-in Dimmer User Manual Federal Communications Commission (FCC) Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 2: Operating Temperature Range
(RF) signal by routing the signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination. ZW39SU is a security enabled Z-Wave Plus® device. A security Enabled Z-Wave Plus® Controller must be used in order to fully utilize the product. - Page 3 ZW39SU User Manual Product Overview A. Push button & LED B. Output Outlet C. Input Plug Button Function Description 1. Press 1x: Turn on/off Outlet Z-Wave network inclusion(ADD) /exclusion(REMOVE) 2. Factory Reset：Remove the switch from power. Press and hold the manual button, plug the switch in and continue holding the manual button for 3 seconds.
- Page 4 ZW39SU User Manual QR Code and DSK The QR code are stocked to the side of the case, DSK is included in the QR code. The DSK code can be found on the DSK label which is attached on the packaging box.
- Page 5 ZW39SU User Manual Command Class Name Version Required Security Class Configuration highest granted Switch Multilevel highest granted...
- Page 6 ZW39SU User Manual Basic Set Mapping Basic CC is mapped to Switch Multilevel Command Class Basic Set is mapped to Switch Multilevel Set. Indicator Command Class The indicator (blue color) will flashes according the indicator set command received from HUB.
- Page 7 ZW39SU User Manual Configuration Parameters Format / Number Name Information Read Only Altering Advanced Default Size LED light mode Set the LED Light Mode. 1 byte unsigned integer Switch Mode Set control mode: 0= Dim mode,1= Switch mode. 1 bytes unsigned integer Minimum Dim Threshold Minimum Dim Threshold.
Need help?
Do you have a question about the ZW39SU and is the answer not in the manual?
Questions and answers