Hobbycraft 6629821000 Instruction Manual
  1. Manuals
  2. Brands
  3. Hobbycraft Manuals
  4. Sewing Machine
  5. 6629821000
  6. Instruction manual

Hobbycraft 6629821000 Instruction Manual

Hide thumbs

Advertisement

Table of Contents

Instruction Manual
6629821000
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 6629821000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Hobbycraft 6629821000

  • Page 1 Instruction Manual 6629821000...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: Read the instructions carefully before you use the machine. Always disconnect or remove the power supply, including batteries, when changing needles or threading machines. Never open the main motor case of the machine.

  • Page 3: Getting Started

    WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the appliance before being charged. Different types of batteries or new and used batteries are not to be mixed. Batteries are to be inserted with the correct polarity.
  • Page 4 Speed Button Select speed by pressing speed button (L) on face of machine. High speed, button is extended out. Low speed, button is in, flush with machine. Use low speed for intricate work, which requires a lot of stopping. starting and turning fabric.Use high speed for long uninterrupted seams.

  • Page 5: Threading The Upper Thread

    Working lamp If additional light is needed, press the light switch to turn the light “ON”. Press the switch again to turn it “OFF”. Thread cutter The machine has a thread cutter on the central left side of the machine. It can cut off the thread after sewing or winding thread.
  • Page 6 1. Insert the thread through eye ⑩ of the needle from the front towards the back of the machine. Use threader if necessary. If necessary, raise the needle (R) to reach the eye by turning the hand wheel (K) slightly clockwise (in the direction away from you). 2.

  • Page 7: Bottom Bobbin Placement

    BOTTOM BOBBIN PLACEMENT: 1. Remove the cover by lifting up where it has popped up at rear. ① 2. Place the bobbin with thread of your choice in the bobbin holder (J) Leaving about 10 inches of thread extended out from the bobbin holder (J) ② 3.

  • Page 8: Connecting Machine To Power Source

    Connecting machine to power source: Attention: Unplug power cord when machine is not in use. Consult a qualified electrician if in doubt regarding how to connect the machine to power source. Connect the machine to a power source as illustrated ① This appliance is equipped with a polarised plug, which must be used with the appropriate polarised outlet ②...
  • Page 9 OPERATING THE MACHINE (without the foot pedal): Follow these simple steps: Lift the needle (R) above the presser foot (F) by turning the hand wheel (K) slightly in a clockwise direction (away from you) ① Raise the presser foot (F) by lifting up on the presser foot lever (G) on the rear of the machine above the presser foot bar ②...

  • Page 11: Changing The Needle

    TO USE THE FOOT PEDAL: (Follow steps 1 - 14 on previous page with these exceptions) 1. Make sure the machine is in the "off" position. 2. Plug the foot pedal jack (M) into the back of machine. 3. Turn the machine on by pressing the foot pedal. 4.

  • Page 12: Winding The Bobbin

    WINDING THE BOBBIN: 1. Always remove the bobbin (S) from the bobbin case on the machine before you wind a new bobbin. 2. Place the thread spool (E) on the thread spindle (C) 3. Put the bobbin pin into the hole on the hand wheel (k) and turn it slightly counterclockwise ①...

Table of Contents