Advertisement

MP20
多功能广播系统
用户说明书
V1.0
2024.03

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MP20 and is the answer not in the manual?

Questions and answers

Summary of Contents for Czi MP20

  • Page 1 MP20 多功能广播系统 用户说明书 V1.0 2024.03...
  • Page 3: Table Of Contents

    目录 一、 产品注意事项............ 01 二、 产品概述............01 三、 MP20参数............02 四、 MP20安装说明...........03 五、 MP20首次使用准备..........04 六、 MP20软件使用说明(云智声、司空2).....07 七、 固件升级............10 八、 恢复出厂设置.............11...
  • Page 4 ..........12 Product Precautions ..........12 Product Overview III............14 MP20 Parameters ........15 MP20 Installation Instructions ......16 Preparation for the First Use of MP20 ..19 MP20 Software Instructions (CZI Sound, FlightHub 2) VII..........22 Firmware Upgrade VIII........24 Restore Factory Settings...
  • Page 5: 一、产品注意事项

    一、产品注意事项 感谢您购买成至智能产品。本文所提及的内容关系到 您的安全以及合法权益与责任。使用本产品之前,请仔细 阅读本文以确保已对产品进行正确的设置。不遵循和不按 照本文的说明与警告来操作可能会给您和周围的人带来伤 害,损坏本产品或其它周围的物品。本文档及所有相关的 文档最终解释权归成至智能所有。如有更新,请访问官方 网站www.czi.com.cn 以获取最新的产品信息,恕不另行 通知。 警告事项 1. MP20如遇硬件问题,请返厂联系售后服务,切勿 自行拆卸维修,否则将失去保修、维修资格。 2. MP20最大声压120dB,近距离使用可能会对人耳 听力造成永久性伤害! 请不要近距离时使用最大音量,否 则由此带来的伤害自行承担! 二、产品概述 MP20是全球首款将喊话器、警灯、降落伞高度融合的 多功能负载,适配DJI Matrice 3D 和 DJI Matrice 3TD无人 机,专门为大疆自动机场2而设计。 扩音器采用双擎驱动,最高声压可达120dB,有效广 播距离200m;通过大疆司空2软件平台进行远程喊话;超 亮的红蓝爆闪灯,有效表明无人机身份;内置无人机降 落伞可瞬间实现毫秒级停桨开伞,平均下降速度约7.2m/s 确保地面人员的安全;防水等级达到IPX4,为行业应用带 来更多可能。...
  • Page 6: 三、Mp20参数

    ① ④ ⑤ ② ③ ⑥ ①:降落伞 ②:爆闪灯 ③:Type-c ⑤:Hypalon绑带 ④:扬声器 ⑥:球头螺丝 三、MP20参数 型号 MP20 外形尺寸 86mm*103mm*57mm 重量 <200g 防护等级 IP34 工作温度 - 20 --- 55℃ 总功率 <36W 警灯功率 声压 120dB@1m 降落伞速度 7.2m/s 软件支持 司空2、pilot 2、成至助手、云智声 录音喊话 喊话方式 多国TTS 文件播放...
  • Page 7: 四、Mp20安装说明

    四、MP20安装说明 1. 将球头螺丝安装在Matrice 3无人机顶部前边两颗螺 丝孔位。 2.将MP20 type-c口插入飞机接口,用大拇指在号角口 压紧球头扣。...
  • Page 8: 五、Mp20首次使用准备

    3.绑好左右两边的绑带(技巧:先把无人机后边绑带 按在机臂下边,再把前边的绑带卡扣按压下去) 4.将MP20安装好后再启动无人机电源 五、MP20首次使用准备 1.激活 ① 先装机并启动飞机,等待司空2上出现PSDK控件...
  • Page 9 ② 点击悬浮窗按钮,获取设备ID和SN ③ 前往成至官网---服务支持---设备激活,输入ID和SN 获取激活码...
  • Page 10 ④ 将激活码输入到司空2的PSDK激活码框,按下回车 即可激活 2.校准指南针 方法一: 通过司空2校准(待大疆司空2支持) 方法二: 通过遥控器校准(将MP20安装在无人机 上后,连接遥控器后如下图操作) ①飞控参数设置...
  • Page 11: 六、 Mp20软件使用说明(云智声、司空2

    ②传感器状态---校准指南针 六、MP20软件使用 如何获取增响音频文件 ① 进入成至官网---服务支持---云智声 ② 点击音频处理,然后上传音频即可获得经过算法处 理的音频 滚滚长江东逝水...
  • Page 12 如何上传音频文件 方法一:成至助手音频文件上传 ① 下载成至助手(成至官网---服务支持---下载中心) ② 使用type-c线将MP20与电脑直接连接 ③ 打开成至助手成功识别到MP20 ④ 点击音乐传输,然后拖动需要上传的文件到文件 窗口并点击上传即可...
  • Page 13 方法二:司空2文件上传 ① 将MP20装在无人机上,打开司空2上的PSDK控件 ② 选择“新建”按钮 ③ 选择需要上传的文件 ② ④ 等待上传完成即可 ③ ① 司空2负载控件介绍 TTS&录音喊话&文件上传 信息栏 音量 警灯...
  • Page 14: 七、固件升级

    七、固件升级 方法一:司空2固件升级(待大疆开放接口) 方法二:成至助手升级 ① 到成至官网获取MP20的最新固件 ② 使用type-c线将MP20与电脑连接 ③ 打开成至助手,等待成至助手成功识别到MP20 ④ 点击离线升级 ⑤ 等待上传完成,并听到升级完成播报即可...
  • Page 15: 八、恢复出厂设置

    方法三:DA2升级 ① 将MP20安装到无人机上,通过type-c线连接飞机与电脑 ② 打开大疆助手DA2软件,进入对应的飞机界面 ③ 选择MP20负载 ④ 选择升级固件,并点击开始升级 ⑤ 等待升级完成即可 八、恢复出厂设置 通过type-c线给MP20供电(连接电脑),然后长按 MP20底部的按钮(丝印产品信息区域),等播放”恢复 出厂“语音的时候就松开按钮,等待重新开机即可。...
  • Page 16: Product Precautions

    Please visit the official website at www.czi.com.cn for the latest product information. Warnings 1. If the MP20 has hardware problems, please return to the manufacturer and contact the after-sales service and do not disassemble and repair by unauthorized personnel otherwise you will lose the warranty and repair eligibility.
  • Page 17 The microphone adopts dual engine drive, the highest sound pressure can reach 120dB, effective broadcasting distance of 200m; remote broadcasting through DJI FlightHub 2 software platform; ultra-bright red and blue flashing light effectively indicating the identity of the drone; built-in drone parachute can instantly realize milliseconds stopping the paddle to open the parachute he average descent speed of about 7.2 m/s to ensure the safety of the ground personnel the waterproof level...
  • Page 18: Mp20 Parameters

    <36W Flashing lights power Sound pressure 120dB@1m Parachute speed 7.2m/s Software support FlightHub 2, pilot 2, CZI Assistant, CZI Sound Recording broadcasting Broadcasting method Multi-country TTS File playback Red and blue slow flash Red and blue fast flash Flashing lights mode Blue and blue sharp flash...
  • Page 19: Mp20 Installation Instructions

    1. Install the ball screws in the two screw holes at the front of the top of the Matrice 3 drone. 2. Insert the MP20 type-c port into the drone interface and press the ball buckle with the thumb at the horn port.
  • Page 20: Preparation For The First Use Of Mp20

    4. Install the MP20 and then start the power supply of the drone. V. Preparation for the First Use of MP20 1. Activation ① First install and start the drone, wait for the PSDK control to appear on FlightHub 2.
  • Page 21 ② Click the floating window button to obtain the device ID and SN ③ Go to Czi official website --- Service Support --- Device Activation, enter ID and SN to obtain the activation code.
  • Page 22 2. Calibrate the compass Method I: Calibrate via FlightHub 2 (to be supported by DJI FlightHub 2) Method II: Calibrate by remote control (after installing MP20 on the drone, connect the remote control and operate as below) ①Flight control parameter setting...
  • Page 23: Mp20 Software Instructions (Czi Sound, Flighthub 2)

    ②Sensor Status --- calibrate the Compass VI. MP20 Software Instructions How to get the sound reinforcement audio file ① Enter Czi official website --- Service Support --- CZI Sound ② Click on the audio processing, and then upload the audio can obtain the audio processed by the algorithm.
  • Page 24 ① Download Czi Assistant (Czi official website--- Service Support---Download Center) ② Use type-c cable to connect M P20 with computer directly. ③ Open Czi Assistant to recognize MP20 successfully. ④ Click Music Transfer, then drag the file to upload to the file window and click Upload.
  • Page 25 Method II: FlightHub 2 file uploading ① Install MP20 on the drone and open the PSDK control on FlightHub 2 ② Select the “New” button ③ Select the file need to be uploaded ④ Wait for the upload to complete ②...
  • Page 26: Firmware Upgrade

    Method I: FlightHub 2 firmware upgrade ( to be opened by DJI interface ) Method II: Czi Assistant upgrade ① Obtain the latest firmware of MP20 from Czi official website. ② Use type-c cable to connect MP20 ③ Open Czi Assistant and wait for Czi assistant to recognize MP20 successfully.
  • Page 27 Method III: DA2 Upgrade ① Install the MP20 on the drone and connect the airplane to the computer via type-c cable. ② Open DJI Assistant DA2 software, enter the correspond- ing aircraft interface ③ Select MP20 load ④ Select upgrade firmware and click start upgrade.
  • Page 28: Restore Factory Settings

    Supply power to MP20 through type-c cable (connect to computer), then long press the button at the bottom of MP20 (silk-screen printing product informa- tion area), release the button when the voice of “Restore Factory” is playing, and wait for restart.
  • Page 29 制造商: 广州成至智能机器科技有限公司 地址: 广东省广州市天河区龙林中街5号 邮编: 510520 邮箱: czzn@gzczzn.com 服务热线: 400-0088-306 COMPANY: Guangzhou chengzhi intelligent Machinery Technology Co.,Ltd ADDRESS: No.5 Longlin Middle Street,Tianhe District Guangzhou City,GuangdongProvince,China EMAIL: czzn@gzczzn.com TEL: 400-0088-306 www.gzczzn.com 更多详情请访问 成至官网 成至公众号 MADE IN CHINA...

Table of Contents

Save PDF