Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for d&b audiotechnik DS100M
Summary of Contents for d&b audiotechnik DS100M
- Page 1 DS100M Manual 1.2 en...
- Page 2 ▪ Avnu Milan™ certification details added. Refer to: Þ Chapter 7.4 "Certifications" on page 18. General information DS100M Manual - preliminary - Version: 1.2 en, 05/2024, D2049.EN .01 Copyright © 2024 by d&b audiotechnik GmbH & Co. KG; all rights reserved.
-
Page 3: Table Of Contents
Service/Maintenance and care........17 6.1 Service..................17 6.2 Maintenance and care............17 Manufacturer's declarations......... 18 7.1 Declaration of Conformity............18 7.2 WEEE Declaration (Disposal)..........18 7.3 Licenses and Copyright............18 7.4 Certifications................18 d&b DS100M Manual 1.2 en - preliminary -... -
Page 4: Ds100M Signal Engine
DS100M Signal Engine DS100M Signal Engine 1.1 Intended use The d&b DS100M Signal Engine is a specialized 3 RU, 19" rack mount audio processor with Milan™ audio networking as well as MADI audio inputs. In its base configuration, it provides a 64 x 64 level / delay audio matrix. -
Page 5: Scope Of Supply
IEC Std.** IEC Std.** *Mains plug types and associated standards / **IEC type IEC Lock: Lockable IEC plug IEC Std.: Standard IEC plug (Illustrations are approximations only and not true to scale) d&b DS100M Manual 1.2 en - preliminary -... -
Page 6: Technical Specifications
65 - 96: IN 3 97 - 128: Not supported WORD CLOCK IN/OUT Controls and indicators Mains power switch Rocker switch on rear panel POWER Push-button switch with integrated ring-LED indicator Boot time Appr.: 45 sec. - preliminary - d&b DS100M Manual 1.2 en... - Page 7 Technical specifications DS100M dimensions in mm [inch] d&b DS100M Manual 1.2 en - preliminary -...
-
Page 8: Startup
13. "ETHERNET indicators" on page 15 button and LED indicator" [10] AUDIO NETWORK indicators. on page 13. Refer to Þ Chapter 4.4.4 "AUDIO NETWORK indicators" on page 15. - preliminary - d&b DS100M Manual 1.2 en... -
Page 9: Rack Mounting And Cooling
▪ If the device is installed in sealed cabinets (e.g. in fixed installations), use additional fan modules with filters that can be easily replaced without opening the sealed cabinets. ▪ Do not rack up DS100M devices together with other devices producing additional heat with opposing airflow. d&b DS100M Manual 1.2 en... -
Page 10: Connections
Two Ethernet ports (ETH 1/ETH 2 - 100/1000 Mbps/peer-to- peer) [2] are provided enabling remote control via Ethernet. Note: The ETH 2 connector is currently disabled but is reserved for future feature implementations. - preliminary - d&b DS100M Manual 1.2 en... -
Page 11: Usb
Startup 4.3.3 USB Two USB 3.0 ports [3] are provided for future functionality. 4.3.4 AUDIO NETWORK The DS100M provides a fully supported Milan™ audio network interface [4] (Gigabit only). PRImary RJ45 Ethernet port (Primary): Used to connect the device to the primary network to transmit and receive audio. -
Page 12: Madi Interface
Startup 4.3.5 MADI interface In addition the DS100M incorporates a fully supported MADI interface which allows the corresponding MADI audio input sources to be transferred via the Milan™ audio network. The assignment of the corresponding MADI input source blocks to the physical MADI inputs on the device are listed in the table below corresponding to the sampling of either 48 or 96 kHz. -
Page 13: Controls And Indicators
▪ Device name is reset to factory default. ▪ All inputs are reverted to Matrix mode. ▪ All input, matrix nodes and output processing is reset. ▪ Device Scenes and network/remote settings are not affected. d&b DS100M Manual 1.2 en - preliminary -... - Page 14 Behavior after re-establishing AC power: Device powers up immediately: Þ Previous 'ON' state restored. Þ Device keeps 'ON' state. Device powers up immediately: Þ Previous 'OFF' state restored. Þ Device shuts down. - preliminary - d&b DS100M Manual 1.2 en...
-
Page 15: Ethernet Indicators
The status LEDs indicate the system and ATDECC identification status: READY ( ) Solid orange: AVB daemon is started and Milan™ communication is enabled. STATE ( / ) Normally off. Flashing white: ATDECC identification active. d&b DS100M Manual 1.2 en - preliminary -... -
Page 16: Milan™/Madi Interfacing
In the screen shot below, MADI input source block 33 - 64 is selected for the DS100M input source block 1 - 32 and Milan™ input source block 1 - 32 is selected for the DS100M input source block 33 - 64. -
Page 17: Service/Maintenance And Care
4. Push-in the top edge of the filter-inlay and spread out the filter- inlay to both sides as shown in the graphic opposite. 5. Finally ensure the filter-inlay is properly fitted in place. d&b DS100M Manual 1.2 en - preliminary -... -
Page 18: Manufacturer's Declarations
Manufacturer's declarations 7.1 Declaration of Conformity This declaration applies to: d&b Z4102 DS100M Signal Engine by d&b audiotechnik GmbH & Co. KG. All product variants are included, provided they correspond to the original technical version and have not been subject to any later design or electromechanical modifications. - Page 20 www.dbaudio.com...
Need help?
Do you have a question about the DS100M and is the answer not in the manual?
Questions and answers