Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Eco Air UC500C30
- Page 1 Range Hood INSTRUCTION MANUAL Model No. UC500C30 READ AND SAVE THE INSTRUCTIONS...
- Page 2 Dear Customer, If you follow the recommendations contained in this Instruction Manual, our appliance will give you constant high performance and will remain efficient for many years to come. CONTENTS WARNING RECOMMANDATION AND SUGGESTION CHARACTERISTICS INSTALLATION & USE MAINTENANCE&CLEAN WARNING TO RUDUCE THE RICK OF FIRE, ELECTRIC SHOCK OR INJURE TO PERSONS, PLEASE OBSERVE THE FOLLOWINGS: Installation work and electric wiring(including switch location) must be done by the qualified person(s) in...
-
Page 3: Recommendations And Suggestions
SMOTHER FLAMES with a close-fitting lid,cookie sheet,or metal tray, then turn off the burner, BE CAREFUL TO PERVENT BURNS.If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. NERVER PICK UP A FLAMING PAN-You may be burned. DO NOT USE WATER,including wet dishcloths or towels- a violent steam explosive will result. -
Page 4: Installation And Use
* Only a qualified and trained service technician can undertake the work of installation and servicing. * Check that the mains voltage corresponds to the one indicated on the rating plate fixed inside the hood. * Check that the domestic power supply guarantees adequate earthing. * Do not connect the hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.) * If the hood is used in conjunction with non-electrical appliances (e. -
Page 5: Ducting Version
to final installation. Caution:To Ruduce Risk of Fire And Electric Shock, Install This rangehood only with integral Blowers manufactured qualified person or agency. WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. - Page 6 Warning: to avoid the risk of fire, use only the metal ductwork . DUCTLESS VERSION The hood discharge kitchen air saturated with odour and fume, passes it through the grease filters and expels it １． to the outside through an outlet pipe. With this version the charcoal filters are not required. No need of plastic or metal duct.
-
Page 7: Ducted Installation
3. Take out the accessory pack (included damper, installation screws ect). DUCTED INSTALLATION Attach 10X3 1/4” Damper/Duct connector or round damper over the knockout openings DUCTLESS INSTALLATION Attach the charcoal filter mat with iron wire and remove the recirculation plate by releasing the screws. 3．... - Page 8 5． Release the wiring fixing clamp by releasing two screws 6． Connect the house power cable to the range hood wring: BLACK to BLACK, WHITE to WHITE and GREEN or BEAR WIRE to GREEN GROUD SCREW.
- Page 9 7． Fixe the wire with wiring clamp by securing two screws. 8． Reinstall the cover plate and filter. 9． Replace the filters and turn on the power at service panel and test for proper operation. Operation The hood is operated using a push button switch or touch sensor switch on the front panel. The blower switch turns the blower on to three speed settings: 0 - OFF 1 - LOW SPEED...
-
Page 10: Grease Filter
CAUTION- The unit is for General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapor Grounding instructions This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. -
Page 11: Hood Cleaning
reinstall the grease filters to the hood. Lighting The hood may use GU10 lamp or LED strip lamp, to change the lamp, please make sure it is switched off. GU10 lamp (Caution: Please DO NOT touch the bulbs as they might be extremely hot) LED Strip lamp Remove the cover plate and lamp plate by releasing the screws. - Page 12 powder with a little water and a soft cloth. * For stubborn cases use a plastic scouring pad or soft bristle brush together with cleanser and water. Rub lightly in direction of polishing lines or “ grain” of the stainless finish. Avoid using too much pressure that may mar the surface. * Do not allow deposits to remain for long periods of time.
Need help?
Do you have a question about the UC500C30 and is the answer not in the manual?
Questions and answers