Page 1
ORDER NO. ITD0403005C1 B05 Canada:B07 LCD TV TC-32LX20 / TC-26LX20 LH34 Chassis SPECIFICATIONS Specifications...
Page 2
Screen Size 22.30” × 13.38” × 26.00” (556.4 mm × 339.8 mm × 660.5 mm) (TC-26LX20) (W × H × diagonal) 27.06” × 16.24” × 31.56” (687.4mm × 412.4 mm × 801.6 mm) (TC-32LX20) Channel Capability VHF-12 : UHF-56 : Cable-125...
Page 3
1. Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Page 4
chassis, the reading must be Figure 1 1.1.2. Leakage Current Hot Check (See Figure 1 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5k , 10 watts resistor, in parallel with a 0.15 capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 1...
Page 5
body by touching a known earth ground. Alternatively, obtain and wear a commercially available dischargingESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
Page 6
3. About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Page 7
Suggested Pb free solder There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also beused. 4. Self-check function When phenomena like "the power fails from time to time" or "the video/audio fails from time to time"...
Page 11
6.2. How to remove the connector Connector type1 Connector type2...
Page 12
7. Disassembly for Service 7.1. Rear cover and Stand 7.1.1. Rear cover 1. Thick cloth and so on is down not to damage a LCD screen, and the unit is layed down as shown in figure below. 2. Detach the Cable cover. 3.
Page 13
4. Remove the screw (6pcs) and release the wires from the clampers on the Rear metal frame, detach the Rear metal frame. Caution: PCB Fixing screws driving torque : 0.2-0.3 N m (2-3kg mm) Do not tighten screws so hard. 7.2.
Page 14
Caution: PCB Fixing screws driving torque : 0.2-0.3 N m (2-3kg mm) Do not tighten screws so hard. 7.3. DV-BOARD 1. Remove the rear cover. (Refer to item 7.1.) 2. Remove the Rear AV bracket. 3. Remove the screws (6pcs) and disconnect a flexible cable (DV7) and detach the DV-BOARD.
Page 15
4. Disconnect the couplers (DG3, DG11) and flexible cables (DG1, DG2, and DG5) and detach the DG-BOARD. Caution: PCB Fixing screws driving torque : 0.2-0.3 N m (2-3kg mm) Do not tighten screws so hard. 7.5. Speaker (L, R) 1. Remove the rear cover. 2.
Page 16
Caution: Speaker Fixing screws driving torque : 0.2-0.3 N m (2-3kg mm) Do not tighten screws so hard. 7.6. K, JG, V-BOARD 1. Remove the rear cover. (Refer to item 7.1.) 2. Remove the Rear AV bracket. 3. Remove the Stand ass’y. 4.
Page 17
Caution: PCB Fixing screws driving torque : 0.2-0.3 N m (2-3kg mm) Do not tighten screws so hard. 7.7. H-BOARD 1. Remove the rear cover. (Refer to item 7.1.) 2. Remove the Rear AV bracket. 3. Remove the screws (2pcs) and disconnect the flexible cable (H2) and detach the H-BOARD.
Page 18
Caution: PCB Fixing screws driving torque : 0.2-0.3 N m (2-3kg mm) Do not tighten screws so hard. 7.9. A-BOARD and B-BOARD 1. Remove the rear cover. (Refer to item 7.1.) 2. Remove the Rear AV bracket. 3. Remove the screws (6pcs) and disconnect the couplers (A3, A21, A22) and the flexible cables (A1, A2, A5, A7) detach the A-BOARD with B-BOARD.
Page 19
2. Remove the Rear AV bracket, the stand ass’y and the Rear metal frame. (Refer to item 7.1.2.) 3. Remove the L-Speaker. (Refer to item 7.5) 4. Remove the screws (4pcs), detach the DV-Board shield frame with DV-Board. 5. Disconnect the flexible cable (DG5) and the couplers (A3, A21, A22, DG3, DG11, P3).
Page 20
Caution: PCB Fixing screws driving torque : 0.2-0.3 N m (2-3kg mm) Do not tighten screws so hard. 8. Adjustment method 8.1. How to enter into adjustment mode While pressing [VOLUME-] button of the main unit, press [RECALL] button of the remote control transmitter three times in a row (within 2 seconds).
Page 21
Main item Sub item Remarks Sample Data MAIN YGAIN Video level (RF, video, component) Video level (RF, video, component) Video level (RF, video, component) COLOR Sub color TINT Sub tint BRIGHT Sub Bright BACK-L Sub Back light B-Y-G B-Y Gain R-Y-A R-Y demodulation axis OPT00...
Page 22
(Aspect mode: just, Viewing mode: vivid normal, AI Picture: off, Backlight: +30) 2. Enter into Main adjustment of YGAIN in the plant adjustment mode, adjust video signal. 2-1. Y signal check With [VOLUME+/-] buttons of the remote control transmitter, adjust the value appearing below YGAIN indication so that the value MAX indication becomes B8.
Page 23
measure the WHITE brightness data to check that it is higher than 400 cd /m (When it is below 400 cd /m , make re-measurement in 30 minutes after cold-on.) 2. For the Excel calculation sheet, use "TH-32LX20, calculation software Ver. 1.05" and "TC-26LX20, calculation software Ver. 1.00".
Page 25
C rank 465 cd/m2 Y < 485 cd/m2 D rank Y < 465 cd/m2 26 inch A rank 540 cd/m2 Y < B rank 520 cd/m2 Y < 540 cd/m2 C rank 500 cd/m2 Y < 520 cd/m2 D rank Y <...
Page 26
Instrument name Connection Remarks 1. Filter jig TP3572 - GND Filter jig 2. RF signal generator RF ANT. INPUT 3. RMS voltage meter Filter jig 1. Apply following RF signal at Antenna input. VIDEO : Flat field, 30 % modulation AUDIO : 300 Hz, 100 % modulation, monaural (70 dB ±...
Page 27
VIDEO : Flat field, 30% modulation AUDIO : 3kHz, 30% modulation, STEREO (LEFT only) (70dB ± 5dB, 75 OPEN, P/S 10dB) Note: After setting 30% modulation with PL SW and NR SW off, turn PL SW and NR SW on. 6.
Page 28
10.2. Power Block Diagram 10.3. Signal Block Diagram 10.4. P-Board Schematic Diagram 10.5. AP-Board Schematic Diagram 10.6. A-Board (1 of 3) Schematic Diagram...
Page 29
10.7. A-Board (2 of 3) Schematic Diagram 10.8. A-Board (3 of 3) Schematic Diagram 10.9. DG-Board (1 of 5) Schematic Diagram 10.10. DG-Board (2 of 5) Schematic Diagram 10.11. DG-Board (3 of 5) Schematic Diagram 10.12. DG-Board (4 of 5) Schematic Diagram 10.13.
Page 57
Ref. No. Part No. Part Name & Description Remarks R858 ERJ6ENF3001 M 3KOHM, 1/10W R859 ERJ6GEYJ223 M 22KOHM,J,1/10W R860 ERJ6GEYJ562 M 5.6KOHM,J,1/10W R861 ERJ6GEYJ152 M 1.5KOHM,J,1/10W R862 ERJ6GEYJ562 M 5.6KOHM,J,1/10W R863 ERJ6GEYJ473 M 47KOHM,J,1/10W R864 ERJ6GEYJ123 M 12KOHM,J,1/10W R865 ERJ6GEYJ153 M 15KOHM,J,1/10W R866 ERJ6GEY0R00...
Page 58
Ref. No. Part No. Part Name & Description Remarks R1005 ERJ6GEYJ103 M 10KOHM,J,1/10W R1007 ERJ6GEYJ473 M 47KOHM,J,1/10W R1008 ERJ6GEYJ103 M 10KOHM,J,1/10W R1009 ERJ6GEYJ182 M 1.8KOHM,J,1/10W R1010 ERJ6GEYJ391 M 390 OHM,J,1/10W R1018 ERDS2TJ223 C 22KOHM, J,1/4W R1050 ERJ6ENF3161 M3.16KOHM, 1/10W R1051 ERJ6ENF2321 M2.32KOHM, 1/10W R1052...
Page 59
Ref. No. Part No. Part Name & Description Remarks R1189 ERJ3GEYJ102 M 1KOHM,J,1/16W R1194 ERJ3GEYJ102 M 1KOHM,J,1/16W R1200 ERJ3GEYJ333 M 33KOHM,J,1/16W R1203-05 ERJ3GEYJ104 M 100KOHM,J,1/16W R1206 ERJ3EKF2701 M 2.7KOHM, 1/16W R1207 ERJ3EKF6191 M6.19KOHM, 1/16W R1208 ERJ3GEYJ102 M 1KOHM,J,1/16W R1210-15 ERJ3GEYJ102 M 1KOHM,J,1/16W R1216 ERJ3GEYJ104...
Page 60
Ref. No. Part No. Part Name & Description Remarks R2331-33 ERJ3GEYJ563 M 56KOHM,J,1/16W R2334 ERJ3GEYJ102 M 1KOHM,J,1/16W R2335 ERJ3GEYJ563 M 56KOHM,J,1/16W R2336 ERJ3GEYJ184 M 180KOHM,J,1/16W R2337 ERJ3GEYJ203 M 20KOHM,J,1/16W R2338,39 ERJ6GEYJ271 M 270 OHM,J,1/10W R2341 ERJ3GEYJ473 M 47KOHM,J,1/16W R2342 ERJ3GEYJ102 M 1KOHM,J,1/16W R2343 ERJ6GEYJ473...
Page 61
Ref. No. Part No. Part Name & Description Remarks R3124-26 ERJ3GEYJ221 M 220 OHM,J,1/16W R3127 ERJ3GEYJ561 M 560 OHM,J,1/16W R3128 ERJ3GEY0R00 M 0 OHM, 1/16W R3129 ERJ3GEYJ561 M 560 OHM,J,1/16W R3130 ERJ3GEY0R00 M 0 OHM, 1/16W R3131 ERJ3GEYJ561 M 560 OHM,J,1/16W R3132 ERJ3GEY0R00 M 0 OHM, 1/16W...
Page 62
Ref. No. Part No. Part Name & Description Remarks R3367 ERJ6GEY0R00 M 0 OHM, 1/10W R3368,69 ERJ6GEYJ102 M 1KOHM,J,1/10W R3371 ERJ3GEYJ102 M 1KOHM,J,1/16W R3372 ERJ3GEYJ473 M 47KOHM,J,1/16W R3373 ERJ3GEYJ274 M 270KOHM,J,1/16W R3374 ERJ3GEYJ105 M 1MOHM,J,1/16W R3375,76 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R3377,78 ERJ3GEYJ182...
Page 63
Ref. No. Part No. Part Name & Description Remarks R4155,56 ERJ6GEYJ821 M 820 OHM,J,1/10W R4157 ERJ6GEYJ681 M 680 OHM,J,1/10W R4158-61 ERJ3GEYJ330 M 33 OHM,J,1/16W R4162 ERJ6GEYJ331 M 330 OHM,J,1/10W R4163 ERJ3GEYJ330 M 33 OHM,J,1/16W R4164 ERJ3GEY0R00 M 0 OHM, 1/16W R4165 ERJ3GEYJ330 M 33 OHM,J,1/16W...
Page 64
Ref. No. Part No. Part Name & Description Remarks R4244-48 ERJ3GEYJ560 M 56 OHM,J,1/16W R4249 ERJ3GEYJ390 M 39 OHM,J,1/16W R4250 ERJ3GEYJ470 M 47 OHM,J,1/16W R4251 ERJ3GEYJ390 M 39 OHM,J,1/16W R4252,53 ERJ3GEYJ560 M 56 OHM,J,1/16W R4254,55 D1HG5608A002 NETWORK RESISTER R4256,57 EXB38V560J RESISTOR ARRAY R4260 ERJ3GEY0R00...
Page 65
Ref. No. Part No. Part Name & Description Remarks R4345 ERJ3GEYJ331 M 330 OHM,J,1/16W R4346 ERJ3GEY0R00 M 0 OHM, 1/16W R4347 ERJ3GEYJ821 M 820 OHM,J,1/16W R4348 ERJ3GEYJ681 M 680 OHM,J,1/16W R4349 ERJ3EKF1000 M 100 OHM, 1/16W R4350 ERJ3GEYJ331 M 330 OHM,J,1/16W R4351 ERJ3GEYJ101 M 100 OHM,J,1/16W...
Page 66
Ref. No. Part No. Part Name & Description Remarks R4585 ERJ3GEYJ102 M 1KOHM,J,1/16W R4586 ERJ3GEY0R00 M 0 OHM, 1/16W R4590 ERJ3GEY0R00 M 0 OHM, 1/16W R4599,00 VLF1144A152T CHIP INDUCTOR J0JBC0000028 R4601 ERJ3GEYJ560 M 56 OHM,J,1/16W R4603 VLF1144A152T CHIP INDUCTOR J0JBC0000028 R4605 VLF1144A152T CHIP INDUCTOR...
Page 67
Ref. No. Part No. Part Name & Description Remarks R5107 ERJ3GEYF333 M 33KOHM, 1/16W R5109 ERJ3GEYF333 M 33KOHM, 1/16W R5110 ERJ3GEYJ223 M 22KOHM,J,1/16W R5111,12 ERJ3GEYF223 M 22KOHM, 1/16W R5113 ERJ3GEYJ223 M 22KOHM,J,1/16W R5114,15 ERJ3GEYJ393 M 39KOHM,J,1/16W R5116 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R5118 ERJ3GEYJ101...
Page 68
Ref. No. Part No. Part Name & Description Remarks R6614 ERJ3GEYJ103 M 10KOHM,J,1/16W R6616 ERJ3GEYJ103 M 10KOHM,J,1/16W R6618,19 ERJ3GEYJ103 M 10KOHM,J,1/16W R6621,22 ERJ3GEYJ103 M 10KOHM,J,1/16W R6624 ERJ3GEYJ103 M 10KOHM,J,1/16W R6626 ERJ3GEYJ103 M 10KOHM,J,1/16W R6628,29 ERJ3GEYJ103 M 10KOHM,J,1/16W R6631,32 ERJ3GEYJ103 M 10KOHM,J,1/16W R6634 ERJ3GEYJ472 M 4.7KOHM,J,1/16W...
Page 69
Ref. No. Part No. Part Name & Description Remarks R6813-15 ERJ3GEYJ333 M 33KOHM,J,1/16W R6816,17 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R6819 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R6822 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R6823 ERJ3GEYJ102 M 1KOHM,J,1/16W R6833 ERJ3GEYJ101 M 100 OHM,J,1/16W D0GB101JA002 R6834 ERJ3GEYJ472...
Page 70
R7141 ERJ6GEY0R00 M 0 OHM, 1/10W Ref. No. Part No. Part Name & Description Remarks R7142-44 ERJ6GEYJ102 M 1KOHM,J,1/10W R7145 ERJ6GEYJ152 M 1.5KOHM,J,1/10W R7146 ERJ6GEYJ561 M 560 OHM,J,1/10W R7147 ERDS2TJ221 C 220 OHM, J,1/4W R7148 ERG1SJ220 M 22 OHM, J, 1W R7149 ERJ6GEYJ391 M 390 OHM,J,1/10W...
Page 71
Ref. No. Part No. Part Name & Description Remarks TNPA3156 CIRCUIT BOARD P TNPA3155 CIRCUIT BOARD AP TXNDG10KDM CIRCUIT BOARD DG TC-32LX20 TXNDG10KFM CIRCUIT BOARD DG TC-26LX20 TXNJG10KDM CIRCUIT BOARD JG TNPA3157 CIRCUIT BOARD K TNPA3158 CIRCUIT BOARD V TXNDV10KDM...
Page 81
TU3801 TUNER SCL1 SCL1 SDA1 SDA1 IC3101 VIDEO SW AUDIO JPEGY VIDEO IN VIDEO SD/PC (JPEG) JPEGC AV1-S.DET AUDIO OUT TV_V MAIN_PR COMP1 Q3118 B-BOARD MAIN_PB MAIN Q3116 MAIN_Y/V Q3114 COMP2 SUB_PR Q3119 SUB_PB LOUT+ Q3117 LOUT- SUB_Y/V Q3115 VIDEO IN SPEAKER AV2-S.DET HDMI...
Page 82
IC5005 Q5016 Q5014 CABLE IN -> Hi : Norm Hi=> MUTE CABLE OUT -> Low : Mute RESET HDMI_DV_ L OUT Q5019 VOUT VDD +3.3V Q5003 HDMI_DV_R R OUT IC5003 AMUTE SMUTE/CSN AUDIO MUTE DVI I/F RECEIVER IC5007 AUDIO AMP RESET MCLK BICK...
Page 83
SD 3.3V JG-BOARD IC6513 IC6516 MCU(JPEG) HDMI_DV_L CARD IC6510 TO DG11 L OUT SLOT D/A ENCODER RDY_BSY RDY/BSY HDMI_DV_R (NTSC) IC6522 BUFFER R OUT CARD BVD1 Q6501 SD 3.3V INVERTER BVD1 Q6505 AMUTE UDIO MUTE DATA DATA Q6502 Q6506 SDWP IC6501 SDCD GPI0...
Page 84
TO JG3 DG11 JPEGY IC1107 JPEGC AVR 3.3V RESET IC1106 VOR 4 STB_RST RST IN LED G ON A_MON_DEF 81 A MON DEF LED R ON REMOCON ALL OFF JPEG-ID0 ZERO X DET 120V ON 29 JPEG-RST MAIN AC RLY RESET KEYSCAN USA_AFT...
Page 85
V-BOARD STAND BY G LED Q1002 LED G D1001 Q1001 LED R POWER STAND BY R LED Q1106 REMOCON STB PS STB 3.3V STB 3.3V Q1105 ALL OFF RM1000 REMOTE SENSOR SW1000 PUSH POWER SWITCH IC1102 EEPROM TO AP2 STB SW Q1112 ZERO X DET 120V ON...
Including TV Stand 33.23” × 22.51” × 12.64” (844 mm × 571.8 mm × 321 mm) (TC-26LX20) 39.37” × 25.66” × 12.64” (1000 mm × 651.7 mm × 321 mm) (TC-32LX20) TV Set Only 33.23” × 18.82” × 5.39” (844 mm × 478 mm × 137 mm) (TC-26LX20) 39.37”...
TC-32LX20 / TC-26LX20 1 Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
TC-32LX20 / TC-26LX20 Caution Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
TC-32LX20 / TC-26LX20 4 Self-check function When phenomena like "the power fails from time to time" or "the video/audio fails from time to time" can not be confirmed at the time of servicing, the self-check function can be used to confirm the occurrence and to limit the scope for the defective circuits.Also, when "the power fails from time to time", display on the screen can be used to confirm the occurrence and to limit the scope for...
TC-32LX20 / TC-26LX20 7 Disassembly for Service 7.1.2. Stand and Rear metal frame 7.1. Rear cover and Stand 1. Remove the Rear cover. 7.1.1. Rear cover 2. Remove the screws (4pcs ), detach the Stand ass’y. 1. Thick cloth and so on is down not to damage a LCD screen, 3.
TC-32LX20 / TC-26LX20 7.2. AP-BOARD 7.4. DG-BOARD 1. Remove the rear cover. (Refer to item 7.1.) 1. Remove the rear cover. (Refer to item 7.1.) 2. Remove the screws (3pcs) and disconnect the couplers 2. Remove the Rear AV bracket.
TC-32LX20 / TC-26LX20 7.5. Speaker (L, R) 1. Remove the rear cover. 2. Remove the screws (4pcs(L), 4pcs(R)) and disconnect the Speaker connector (L, R) and detach the Speakers (L, R). Caution: PCB Fixing screws driving torque : 0.2-0.3 N m (2-3kg Do not tighten screws so hard.
TC-32LX20 / TC-26LX20 7.8. P-BOARD 7.10. LCD panel 1. Remove the rear cover. (Refer to item 7.1.) 1. Remove the rear cover. (Refer to item 7.1.1.) 2. Remove the Rear AV bracket. 2. Remove the Rear AV bracket, the stand ass’y and the Rear metal frame.
TC-32LX20 / TC-26LX20 8 Adjustment method 8.1. How to enter into adjustment mode While pressing [VOLUME-] button of the main unit, press [RECALL] button of the remote control transmitter three times in a row (within 2 seconds). 8.1.1. Adjustment method..Use the remote control.
TC-32LX20 / TC-26LX20 8.4. Video Signal Level Adjustment 8.4.1. NTSC picture RF Instrument Name Connect to Remarks 1. Remote controller RF input 2. Internal signal (sprit color bar) 1. Receive sprit color bar, turn off CC. (Aspect mode: just, Viewing mode: vivid normal, AI Picture: off, Backlight: +30) 2.
TC-32LX20 / TC-26LX20 8.5. White Balance Adjustment Instrument Name Connect to Remarks 1. Remote controller Correlation can be also taken 2. LCD WB meter (Minolta CS-1000 equivalent) by CA-110 or equivalent 3. Communication jig 4. Computer for external control · Basically perform checking using the production software and make automatic adjustment using external computer.
Page 133
TC-32LX20 / TC-26LX20 8. Measure the brightness of white after adjustment, Manage the data grade the brightness on mentioned below. 32 inch A rank 510 cd/m2 Y < B rank 485 cd/m2 Y < 510 cd/m2 C rank 465 cd/m2 Y <...
P-BOARD D7100 T7001 INVERTER V B/L POWER LCD PANEL V B/L POWER INVERTER-VCC IC805 V_OUT AP-BOARD V_IN ON/OFF TO DG2 INVERTER VCC IC7106 IC7102 Q7100 Q7103 MAIN 3.3V OCP/FB PHOTO V REF 14V/3.2A MAIN 3.3V COUPLER Q810 MAIN 3.3V INVERTER-VCC SUB 5V 30V/1.0A SUB 5V...
TU3801 A-BOARD TUNER H-BOARD SCL1 SCL1 SDA1 SDA1 IC3101 VIDEO SW JK3002 AV1-V AUDIO VIDEO1 IN AV1-S-C JPEGY VIDEO IN VIDEO SD/PC AV1-S-DET JPEGC (JPEG) AV1-S.DET AV1-S-Y AUDIO OUT COMPONENT1-Y COMP1 TV_V MAIN_PR COMPONENT1-PB COMP1 Q3118 B-BOARD MAIN_PB COMPONENT1-PR MAIN Q3116 DTV1 MAIN_Y/V...
Page 139
SD 3.3V JG-BOARD IC6513 IC5005 Q5016 Q5014 CABLE IN -> Hi : Norm IC6516 CABLE OUT -> Low : Mute Hi=> MUTE MCU(JPEG) RESET CARD HDMI_DV_L L OUT IC6510 TO DG11 SLOT D/A ENCODER RDY_BSY Q5019 RDY/BSY VOUT VDD +3.3V Q5003 HDMI_DV_R (NTSC)
Page 140
TO JG3 DG11 JPEGY IC1107 JPEGC AVR 3.3V RESET V-BOARD IC1106 VOR 4 STAND BY G LED STB_RST RST IN Q1002 LED G ON LED G D1001 A_MON_DEF Q1001 81 A MON DEF LED R ON LED R POWER STAND BY R LED REMOCON Q1106 REMOCON...
Need help?
Do you have a question about the TC-32LX20 and is the answer not in the manual?
Questions and answers