fdmt WAVEWAND Manual

WAVEWAND - Tube light
Specification:
Size: Height 100 cm x Diameter 5 cm Base Size: 20.5 cm x 20 cm
Material: PC
60 non – replaceable LEDs 6 W
LED: 6 non – replaceable multi coloured LEDs 0.5 W
Input: 100-240 V ~ 0.5 A Max 50/60 Hz
Output: 12 V 1 A
Required:
Phillips head Screwdriver, Power Drill, Hammer
WARNINGS:
Contains sequences of flashing lights which may affect individuals who are susceptible to photosensitive epilepsy or other photosensitivities.
This is not a toy and is to be used under adult supervision only.
This product can be wall-mounted. It is the responsibility of the consumer to assess the wall structure and ensure it is adequate and strong enough for wall
mounting. We recommend to regularly check to ensure the light is firmly attached, that it continues to work properly, and that no screws or connections have
become loose over time.
Safety Warnings:
• Before setting up your light, make sure that the product is not damaged. If any part of the product is damaged, do not attempt to assemble and use.
• Only use the adaptor supplied with this product and no other adaptor must be used.
• Ensure that the light is standing on a flat, stable surface.
• Ensure that the light is placed where it cannot be knocked over.
• Do not operate in its packaging.
• Do not attempt to replace the "non-replaceable" bulbs.
• Do not electrically connect the light to another product.
• Unplug when it is not in use or unattended for long periods of time.
• Ensure that the cable is placed so that no trip, entanglement or strangulation hazards are likely to occur.
• Do not allow any part to come into contact with excessive heat or naked flames.
• Ensure that the light is not covered up and there is adequate airflow around the light.
• Avoid damage to the light and wiring. Do not use if any part of the light or adaptor has been damaged.
• Carry out regular check ups to ensure fixings, fittings and installation have not become loose.
• This light can only be used indoors. Do not use in wet, damp or excessively humid conditions. The light uses non-replaceable LED bulbs, but the bulbs have
been designed to be used for many hours.
Instructions:
Please read the following instructions carefully to ensure satisfactory and safe operation of the light.
1. Carefully remove the light tube and its contents from the packaging.
2. When choosing a location for the light, make sure that the socket is close enough to the light and that the cable will not become an obstacle or hazard.
3. Put the feet in a cross position, ensuring the screw holes align correctly.
4. Align the silver cap with the feet and insert the 4 screws from under the feet. Using a Phillips head screwdriver tighten the screw to hold the feet and
cylinder into position.
5. Before inserting the light tube to the base, connect the adaptor to the tube (ensuring the adaptor wire is not trapped and is feeding out of the cut slit in
the cap) and then insert the light tube into the base slot.
6. Plug the adaptor to the power outlet and switch on.
PLEASE NOTE: There are 4 pre-drilled holes on each end of the feet. This is if you wish to mount the stand to the floor to avoid it falling over. Fixers for this has
not been supplied by the manufacturer.
Wall Mounting:
1. Mark holes on the wall where you wish to mount the brackets.
2. Using a power drill, make holes in the wall. Insert wall plugs, hammer may be required to push the wall plugs in.
3. Align the wall bracket and insert the screws.
4. Sit the light tube on the wall bracket. Ensure that it is securely sitting in position.
5. Connect the adaptor to the base of the light tube.
6. Connect the silver cap (ensuring the adaptor wire is not trapped and it is feeding out of the cut slit in the cap).
7. Plug the adaptor to the power outlet and switch on.
Remote Control Functions:
Remove the tab before operating. Always operate remote control within 1 meter of the light. If the remote does not appear to be working, insert new battery. To
change the battery, instructions are found on the back of the remote control. The remote control requires 1x CR2025 3 V Lithium battery to operate.
Battery Warnings: Batteries should only be inserted or changed by an adult. Non-rechargeable batteries are not to be recharged. Be sure to insert batteries with
the correct polarities and always follow the product and battery manufacturers' instructions. Remove batteries from the product before extended storage. Always
remove old or exhausted batteries from the product. The supply terminals are not to be short circuited. Check that the contact surfaces are clean before installing
batteries. Do not mix different types of batteries. Do not bury or burn batteries. Recycle used batteries responsibly. Do not mix old and new batteries. Do not dis-
pose of in household waste. Warning: Dispose of used batteries immediately. Keep new and used batteries away from children. If you think batteries might have
been swallowed or placed inside any part of the body, seek immediate medical attention.
Disposal: The "Crossed Wheelie Bin" symbol on the product means that the product is classed as Electrical or Electronic equipment and should not be
disposed with other household or commercial waste at the end of its life. The goods must be disposed of according to your city guidelines.
Please retain these instructions as it contains important information.
Made in China
Contents:
1 x LED Light Tube
1 x Remote Control (with CR2025 Lithium battery included)
1 x Adaptor
2 x feet + 4 x Screws
2 x Wall Mount Brackets + 2 x Wall Plugs and 2 x Wall Screws
420 Jean-Neveu, Longueuil (QC) J4G 1N8
1.866.465.0559 / service@fdmt.ca
4244000