ElectrIQ EQDO1 Service Manual
  1. Manuals
  2. Brands
  3. ElectrIQ Manuals
  4. Oven
  5. EQDO1
  6. Service manual
ElectrIQ EQDO1 Service Manual

ElectrIQ EQDO1 Service Manual

Built in / built under double oven
Hide thumbs
Table of Contents

Advertisement

Quick Links

BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL
This document is prepared to show how to disassemble below parts located in the
If you have any questions, you can contact with below e-mail address.
Built In / Built Under Double Oven products.
Support@electriQ.co.uk
3
5
6
7
8
9
9
10
11
12
13
14
15
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EQDO1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ElectrIQ EQDO1

Summary of Contents for ElectrIQ EQDO1

  • Page 1: Table Of Contents

    This document is prepared to show how to disassemble below parts located in the Built In / Built Under Double Oven products. If you have any questions, you can contact with below e-mail address. Support@electriQ.co.uk Front Panel and Knobs ...
  • Page 2 BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Front view of the product Rear view of the product...

  • Page 3: Front Panel And Knobs

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL FRONT PANEL AND KNOBS Disassemble the screws under the front panel like shown above picture. Pull the knobs like shown way above picture.
  • Page 4 BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Push upon the clip and turn the knob like shown in the above picture to disassemble the knobs. Disassemble two screws which are shown in the right picture above in order to change encoders. After disassemblying knobs and terminals on the front panel, pull the panel like shown in the above picture.

  • Page 5: Timer

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Timer Remove the terminal connections to change the digital timer. Push upon the pawls of the timer to remove it.

  • Page 6: Cooling Fan Motor

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Cooling Fan Motor Remove the socket terminals of cooling fan motor. Remove the connections of cooling fan cover on the fan duct. Unscrew the screws on the top insulation cover, then change the cooling fan motor.

  • Page 7: Capillary Thermostat

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Capillary Thermostat Unscrew the connection screws on the inner panel and remove the terminals of the thermostat. After disassemblying the rear panel, pull the thermostat bulb to remove.

  • Page 8: Switch - Seal

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Switch Unscrew the connection screws on the inner panel and remove the terminals of the switch. Note: After changing the switch, electrical connections needs to be done following the circuit diagram. Seal Open the door of the oven.

  • Page 9: Lamp

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Lamp Remove the lamp lens by turning it from innerside of the oven, then disassemble the rear panel. Remove the socket connections on the lamp, then remove the lamp by taking out from its pawls. Limit Thermostat Remove the rear panel.

  • Page 10: Top Heating Element - Bottom Heating Element

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Top Heating Element Remove the rear panel. Then, space the insulation wool gently to remove the socket terminals. After that, unscrew the connection screws from inside of the cavity. The heating element will be free. Bottom Heating Element Remove the rear panel.

  • Page 11: Ring Heating Element

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Ring Heating Element Remove the fan cover. After that, unscrew the connection screws of the ring heating element. Then, remove the terminal connections of the heating element.

  • Page 12: Fan Cover - Fan Motor

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Fan Cover – Fan Motor Unscrew the connection screws from inside of the cavity to remove the fan cover. Remove the nut on the impeller by turning to anticlockwise via a proper wrench. Remove the rear panel.

  • Page 13: Catalytic Panel

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Catalytic Panel Unscrew the connection screws on the edges to remove the catalytic panel. Unscrew the two connection screws shown below. After that, remove the panel from its pawls below.

  • Page 14: Door

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Door Unlock the hinge’s lock mechanism first. Then, pull the door to release it.

  • Page 15: Error Codes - Demo Mode

    BUILT IN / BUILT UNDER DOUBLE OVEN PRODUCTS SERVICE MANUAL Error Codes – Demo Mode RTC Crystal Change the is missing. control card. DIGITAL TIMER MODELS’ DEMO MODE:  For activating demo/shop mode; in 1 minute when the electricity is first connected, “Mode” and “- “ should be pressed together for 5 seconds.

Table of Contents