Page 3
How to recognize your product ? Find ID number marked on product: BC108-107XXXX When the Sports Computer BC108-107XXXX is detected by CoospoRide APP, the APP displays Sports Computer ID number.
Page 6
Main Device x1 Charging Cable x1 User Manual Rubber pad for Standard bike Big size rubber standard bike mount x1 mount x1 ring x2 Small size rubber ring x2 1. Install the rubber pad onto 2. Tie the mount onto the bar with 3.
Page 7
1. Please charge the device before first time use; 2. Please use DC 5V power adaptor for charging; 3. During the charging, the battery icon will flash until fully charged; USB DC 5V power adaptor / Computer This device will automatically calculate the sun rise and sun set time, from the half an hour before sun set to half an hour after sun rise, the back light will be automatically lighten up, in the rest of the time, the back light will be turned off if no operation detected in 15 seconds.
Page 8
1 Please make sure the sensors are in wake-up mode ( For example the heart rate monitor should be worn properly, for speed,cadence; and power meter, rotate the crank or the wheel to wake it up ). Wear it correctly, wake up the heart rate monitor For speed, cadence, and power meter, rotate the crank or the wheel to...
Page 9
1.1 Hold the to get into setting mode; 1.2 There are 4 settings pages available ( P1~P4), the first page is P1 after entering the setting mode; 1.3 Press to selct to enter; 1.4 The bike computer automatically searches for ANT+ accessories, and automatically connects after searching for ANT+ accessories;...
Page 10
1.1 Hold the to get into setting mode; 1.2 There are 4 settings pages available (P1~P4), press the to switch to P2; 1.3 Press to select to enter; 1.4 Press to select the setting digit, press the to set the numbers; 1.5 Press to save and exit ( Automatically exit in 6 seconds if no operation detected ).
Page 12
1.1 Hold the to get into setting mode; 1.2 There are 4 settings pages available ( P1~P4), press the to switch to P3; 1.3 Press to select to enter ( Default time zone: UTC/GMT+ 08:00); 1.4 Press to select the setting digit, press the to set the numbers; 1.5 Press to save and exit ( Automatically exit in 6 seconds if no operation detected ).
Page 13
Turn on the device, press to start an exercise and recording (During the cycling, when the cycling speed is 0, the device will pause automatically, if no data get for speed, cadence and heart rate in 15 minutes the device will turn into sleep mode, press to resume ) Countdown Press...
Page 14
*Bluetooth Connection & Timing function activate To activate timing function, please scan the QR code above to download the App CoospoRide. Once activate the timing function, you don’t need to activate it again when the next tile use BC108-. iOS 9.0 version and aboce, iphone 4s and above Any Bluetooth 4.0 enabled Android device with Android 4.3 and above 1- Open the APP CoospoRIDE, register and log in ( click Agree on all...
Page 15
4- After successful connection, the timing function will be automatically activated to the bike computer BC108-. 5- Attention, the time on the screen now only shows the time of time zone 0. If you are in another time zone of the world, please go page 12 of this manual to set correct time zone.
Page 16
The water resistant level of the bicycle computer is IPX7. It can be used in the rain if you close the protective cover on the back tightly. It is recommended to take down the bicycle computer and put it into waterproof bag if it rains heavily.
Page 17
USER MANUAL SPEED AND CADENCE 2 IN 1 SENSOR KIT SENSOR KIT BK804L...
Device Overview Sensor - IP68 Electronic box Bluetooth-IP67 (With CR2032 battery) Detection magnet x1 3*Blue+3*Silver Short cable ties*6 RubberPads & Ties Long cable ties*6...
Page 19
How to recognize your product ? 1- Find ID number marked on product: BK804L-000XXXX 2 -When the Sensor BK804L000xxxx is detected by CoospoRide APP, the APP displays sensor ID number. 3- When the Sensor BK804L000xxxx is detected by Sports COmputer, the Sports Computer displays the last 4 digits of the sensor ID number xxxx.
Installation Electronic box Bluetooth - IP67 ( With CR2032 battery ) Counter Above the water Underwater Turn the crank to wake up and detect the system straps Detection magnet (To be Sensor-IP68 In front fixed on the inside of the of the passage of crank ) the magnet (1cm)
Replacing the battery Use CR2032 type batteries. The battery life is 500 hours To open the case, unscrew with a coin. Remove the battery Separate the device Dispose of used batteries immediately in accordance with local regulations Replace the battery with the (+) side up.
If the cadence or speed information is missing, check the position of the installed magnet and sensor. The magnet must pass in front of the sensor with a maximum distance of 1,6 cm. Ant+ and BLE capabilites allow for wireless connection to both smartphones and the meter at the same time or separately.
Product Introduction Thank you for purchasing our ANT+ & BLE heart rate armband, this product is one of the heart rate monitors of our company, which transmits the real-time heart rate data through Bluetooth or ANT+ to heart rate receiving device, sports and health App helping you to manage your exercise intensity scientifically.
Page 25
Charging - Pleace charge the device before first time use; - Pleace use DC 5V power adaptor for charging; - When charging, LED will flash green and red alternately.Green light stay one means fully charged. Heart Rate Sensor Charging Terminals Charging Cable Connect USB DC 5V power adapter or computer USB The product has a built-in battery.
Function and Operation Start-up Button Turn-on: Press the start-up button, the LED light will flash blue quickly until the heart rate was found, then the light will flash slowly. Red light indicates the device is in a low battery state and needs to be charged.
Page 27
Heart Rate Sensor Disassembly Press the front of the sensor to take out the sensor ( Figure 1 ); Aligned with the raised position and stuck intro the groove position to install the sensor ( Figure 2 ) Connection Compatible with most third party fitness Apps ( Strava, CoospoRide...).
Applicable models iOS 9.0 version and adove, iphone 5s and above. Any Bluetooth 4.0 enabled Android device with Android 4.3 and above. Basic Parameters Product size : 35,2 x 34 x 10,9 mm Transmission : BLE & ANT+ Host weight : 7,7g Power : Rechargeable lithium battery Battery life: 20 hours for continuous heart rate monitoring Autonomie à...
Statement: Thank you very much for choosing this product ! Before using this product, please read the manual carefully. All information in this manual may change without notice. The Company has the right to change the information at any time without prior notice. Installation Method 3.
Page 31
Phone installation Method Open the bracket waterproof box, pull the buckle outwards, put the mobile phone, cove the lid and fasten the buckle. M18S/Installed size : 168 x 83 x 10.5 mm Product Structure Display Back transparent film Rebound base Front touch film Buit-in waterproof...
Page 32
Instructions for use Thank you for choosing this mobile phone holder. For the sake of safe and convenient use of this product, please read the product manual carefully berfo use and keep it properly for reference. This product is a conveninent mobile phone holder, quick installation, easy to take and put waterproof life, rainy riding, touch screen design, can let you easly enjoy music navigation directions during the cycling process, random charging.
Need help?
Do you have a question about the myAQUAFIT and is the answer not in the manual?
Questions and answers