Advertisement

Bedienungsanleitung
Scale Rumpf MD500D
450er Größe
1. INTRODUCTION
Thank you for buying Roban Model products. The 600 size MD500D/E scale fuselage is designed as an
easy to use product. Please read the manual carefully before assembling the model, and follow all
precautions and recommendations located within the manual. Be sure to retain the manual for future
reference, routine maintenance and tuning. The scale fuselage is designed for T-REX 600 Helicopter
series use. You can easily put it on your T-REX 600 for new clothing.
Important Note
Roban Model R/C Helicopters are advanced, high-performance devices, built incorporating the latest
technologies. They are not intended as toys, and improper use can potentially lead to serious injury,
or even fatal accidents. We implore you to read this manual thoroughly before operating these
models. Safety should be your utmost priority - not just your own, but also that of others and your
surroundings when piloting Roban Model products.
Liability Disclaimer:
The manufacturer and the seller cannot accept liability for the operation or misuse of this product.
Roban Model R/C helicopters are intended to be used exclusively by experienced adults in legally
sanctioned flying fields. Once sold, we cannot monitor or control the product's operation or usage.
Operation Guidelines:
Upon assembly of the scale fuselage, the weight and complexity of the structure will increase. To
mitigate risk of accidents and damages, we advise against attempting 3D flights.
Skill Requirements:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Scale Rumpf MD500D and is the answer not in the manual?

Questions and answers

Summary of Contents for Roban Model Scale Rumpf MD500D

  • Page 1 450er Größe 1. INTRODUCTION Thank you for buying Roban Model products. The 600 size MD500D/E scale fuselage is designed as an easy to use product. Please read the manual carefully before assembling the model, and follow all precautions and recommendations located within the manual. Be sure to retain the manual for future reference, routine maintenance and tuning.
  • Page 2: Contents Of Kit

    The operation of R/C products necessitates a certain level of skill and familiarity. Any damages or dissatisfaction resulting from accidents, modifications, or operational mishaps are not covered under any warranty. Consequently, such products cannot be returned for repair or if you experience problems during operation or maintenance.
  • Page 3 CONTENTS Item No. Description Quantity Landing gear struts Landing gear skids Washer 3x12x70 Washer 3x12x51 Mounting bracket Screw A2x10 Screw M2x24 Washer M2 Nut M2 EVA rear rubber Tail fin Screw M2x18 Washer M2 Horizontal tail Vertical tail Upper washer Front washer Rear washer REQUIRED TOOLS / CONSUMABLES...
  • Page 4: Installation

    4. INSTALLATION 4.1 Attach the landing gear struts using epoxy adhesive from the inside as shown. 4.2 Assemble the skids as shown and glue them together. 4.3 Remove any excess plastic with a hobby knife.
  • Page 5 4.4 Glue the washers together as shown. 4.5 Install the mounting bracket as shown with 4 pieces of Screw A2x10. 4.6 Remove the tail rotor from the mechanism. Note: The rear stack of washers is fixed to the mechanism. When installing the mechanism, this is pushed into the bracket since the screws are very difficult to access once the mechanism is installed.
  • Page 6 Install the washers. Insert the mechanism. The wooden adapter must be inserted into the detent.
  • Page 7 4.10 Secure the front section with 2 pieces of Screw A2x10 as shown. 4.11 Install the rear rubber. 4.12 Install the tail rotor.
  • Page 8: Spare Part List

    4.13 Install the tail fin with a screw. 4.14 Glue the tail unit with epoxy resin adhesive as shown. 5. SPAREPART LIST HSB- 450MD500E 前 450 MD500E MD450EPJ001 MD450GJB-E 头 canopy 450MD500E 侧 450 MD500E MD450EPJ002 窗 window set 450MD500E 平 450 MD500E MD450EPJ003 垂尾...
  • Page 9: Landing Gear

    450 MD500E 450MD500E 脚 MD450EPJ004 landing 架组 gear 450 MD500E 450MD500E 固 MD450EPJ005 mounting 定件 hardware 450MD500E 水 450 MD500E MD450EPJ006 印 decals HSB- 450MD500D 前 450 MD500D MD450DPJ001 MD450MG-D 头 canopy 450MD500D 侧 450 MD500D MD450DPJ002 窗 window set 450MD500D 平...
  • Page 10 6. FULLY ASSEMBLED FUSELAGE Align TREX450 und baugleiche Mechaniken Specifications: Lenght: 695mm Height: 365mm Width: 158mm Weight: 330g Suitable for Align TREX450ESP/EFL/PRO and derivatives We wish you a lot of fun with the fuselage! Copyright 2024 – www.robanmodel.com...

Table of Contents