Subscribe to Our Youtube Channel
Related Manuals for Kayakpro Xeon 2.0
Summary of Contents for Kayakpro Xeon 2.0
- Page 1 KayakPro® Xeon 2.0 Kayak Ergometer ASSEMBLY MANUAL v 2.0 KP-A-00250 REV 02 KayakPro® Xeon 2.0 Kayak Ergometer...
-
Page 2: Safety Precautions
6. Do not modify the machine. 7. Children must not be allowed near this machine. 8. Teenagers must be supervised in the use of this machine. 9. By using the KayakPro® Xeon Kayak Ergometer the user accepts all and full responsibility for self. - Page 3 GENERAL General Notes Tools required: 4mm Hex Allen Key 5mm Hex Allen Key 6mm Hex Allen Key Side Cutters (for Cable Tie) 2111...
- Page 4 STEP 1 Attach Rear Foot to Rear Leg Assembly M8x30 CAP HEAD SCREW...
- Page 5 STEP 2 Attach Front Foot & Foot Assemblies to Front Leg Assembly M8x30 CAP HEAD SCREW...
- Page 6 STEP 3 Fit Bearing Blocks & Pull Bar to Footrest Assembly M6x12 BUTTON HEAD SCREW Do not fully tighten at this stage Select location holes to suit user M5x30 BUTTON HEAD SCREW M5 WASHER...
- Page 7 STEP 4 Assemble Footrest Rails Lift Plunger to insert Rails. Slide Rails to be in line. Ensure both Plungers are fully engaged. Fully tighten after assembling FOOTREST MOUNT FOOTREST MOUNT M6x12 BUTTON HEAD SCREW x 16 Ensure Footrest is free to slide full length of Rails &...
- Page 8 STEP 5 step description M8x16 BUTTON HEAD SCREW M8 WASHER...
- Page 9 STEP 6 Fit Seat Platform & Seat M8x20 BUTTON HEAD SCREW M8 WASHER x 10 Select location holes to suit user M5x16 CAP HEAD SCREW M5 SPRING WASHER M5 WASHER...
- Page 10 STEP 7 Fit Front Leg to Beam M8 WASHER M8x16 BUTTON HEAD SCREW...
- Page 11 STEP 8 Fit Footrest & Rails to Beam Assembly M8x30 BUTTON HEAD SCREW M8 WASHER...
- Page 12 STEP 9 Fit Console M8 WING NUT M8 WASHER x 18 M6x20 BUTTON HEAD SCREW M8x80 HEX HEAD SCREW...
- Page 13 STEP 10 Thread Rope Through Beam Assembly...
- Page 14 STEP 11 Fit Flywheel - Upper Mount M8 WASHER x 20 M8x20 BUTTON HEAD SCREW M8 SPRING WASHER Allow Flywheel to rest on floor whilst securing screws finger tight Note position of Control Lever & Vents...
- Page 15 STEP 12 Thread, Secure & Connect Speed Sensor Cable CABLE TIE CABLE TIE...
- Page 16 STEP 13 Fit Flywheel - Lower Mount M8 WASHER For ease of fixing place Xeon on the side to secure Flywheel M8 SPRING WASHER to Lower Flywheel Bracket M8x20 BUTTON HEAD SCREW Loosen Lower Flywheel Bracket if required to align with Flywheel...
- Page 17 STEP 14 Tighten Upper Flywheel Mount & Lower Flywheel Bracket Tighten Upper Flywheel mounting screws, 2x Tighten Lower Flywheel Bracket mounting screws,...
- Page 18 STEP 15 Fit Flywheel Pulley Assembly M6x12 BUTTON HEAD SCREW M6 WASHER...
- Page 19 STEP 16 Assemble Paddle Shaft Minimum insertion 20cm both sides Keep both sides equal LOCKED UNLOCKED...
- Page 20 STEP 17 Connect Rope to Paddle Shaft and Recovery Adjustment Overhand knot. Initial tail length = 280mm (11"). Adjust tail length to suit user. Longer = quicker recovery.
- Page 21 STEP 18 Wrap Rope Around Catch Pulley ROPE PATH CATCH ROLLER...
- Page 22 STEP 19 Fit Side Panels Remove red plastic backing film Position top edge 3-5 mm below top surface of Beam Assembly using light pressure. When aligned press firmly along length.
- Page 23 INFO Rope & Elastic Cord Layouts ROPE LAYOUT ELASTIC LAYOUT...
- Page 24 KayakPro USA LLC 1344 Van Buren St, Hollywood, Fl 33019, Email: sales@kayakpro.com www.kayakpro.com KP-A-00250 REV 02 KayakPro® Xeon 2.0 Kayak Ergometer...
Need help?
Do you have a question about the Xeon 2.0 and is the answer not in the manual?
Questions and answers