Subscribe to Our Youtube Channel
Summary of Contents for Maytronics e Series
- Page 1 Drive e Series Dosing Pump Instruction Manual Ensure Acid is diluted, as per page 5 of these instructions. www.maytronics.com.au...
-
Page 2: Table Of Contents
The pH Drive is quite easy to operate, and this manual will explain each of the steps clearly. Troubleshooting and hints are also included to allow you to get the most from your unit. If you require assistance at any stage, please contact your Maytronics Authorised Dealer. Page CAUTIONS &... -
Page 3: Cautions & Warnings
Drive should be installed out of authorised service agent. Please contact reach of children. Children must not have your Maytronics Authorised Dealer for access to operating the pH Drive without detail s . Despite being low-voltage adult supervision. -
Page 4: Getting To Know Your Ph Drive
Getting to know your pH Drive DOSING PUMP High quality, low maintenance peristaltic dosing pump. POWER CONNECTOR IP65 Waterproof connector plugs into May t ronic s Ozone Sw im systems that are equipped with the matching outlet. MOUNTING CLIP Pull the clip downwards when mounting the pH Drive to the mounting rail, or to unclip when removing. -
Page 5: Acid Safety & Dilution
Acid Safety & Dilution Maytronics recommends using pre-diluted acid purchased from your reputable pool shop or service agent. Alternatively, this section provides information on the safe handling and dilution of acid to use with your pH Drive. Please take the time to read and understand this section, to prevent injury or illness due to acid spillage. -
Page 6: Injection Tee Installation
Injection Tee Installation Install the Injection Tee first, so that the glue can set while you are installing the pH Drive unit itself. Pre-Installation Checklist ! You will require a saw suitable for cutting ! For installations into 40mm Pipe, a pair of PVC pipe, PVC Primer and PVC Glue. -
Page 7: Ph Drive Installation
pH Drive Installation Pre-Installation Checklist ! The pH Drive unit MUST be mounted Ensure that the pH Drive is protected from vertically, with the cables at the bottom, in direct sunlight and weather. Although the order to be weather resistant. Any water unit has a weather resistant design, ingress due to the unit being incorrectly damage from long term exposure is not... -
Page 8: Tube Installation
Tube Installation INJECTION TEE TUBE INSTALLATION Remove the nut from the non return valve Tighten the nut over the tube. Tighten firmly on the Tee piece. Slip the Nut over the tube. with fingers. If the tubing can still be easily pulled out, use a tool to tighten an extra 1/2 Push the tube firmly onto the tube fitting. -
Page 9: Completed Installation (Illustration)
Drum weight inside acid drum. Connect Power Lead Locate the pH Drive power socket on your Maytronics Ozone Swim system. Remove the dust cover. The keyway of the power socket is towards the front of the unit. Align the pH Drive plug with the keyway of the socket and push in. -
Page 10: Ph Drive Settings
pH Drive Settings The Acid Dose Rate of the pH Drive is If the pool pH test is too high, increase the controlled by the Ozone Swim unit. The Dose Rate setting. Ozone Swim will switch the pH Drive’s pump The Dose Rate table assumes acid to water on for a short Run Time every two hours dilution of 1 to 3 parts, as per page 5. -
Page 11: Changing Pump Cassette
Changing Pump Cassette The pH Drive’s dosing pump squeeze tube The pH Drive’s dosing pump squeeze tube The pH Drive’s dosing pump squeeze tube The pH Drive’s dosing pump squeeze tube The pH Drive’s dosing pump squeeze tube The pH Drive’s dosing pump squeeze tube The pH Drive’s dosing pump squeeze tube The pH Drive’s dosing pump squeeze tube The pH Drive’s dosing pump squeeze tube... -
Page 12: Warranty
Web ..... . . www.maytronics.com.au ABN......87 148 058 495...
Need help?
Do you have a question about the e Series and is the answer not in the manual?
Questions and answers