Subscribe to Our Youtube Channel
Summary of Contents for Boekel 151050
- Page 1 Digital Oven Series 151050 151050-2 151140 151140-2 151250 151250-2 151500 151500-2 Operating Instructions N2400400 Rev. 1 Feb 2023...
-
Page 2: Table Of Contents
Table of Contents Safety ..................3 Intended Use of Product ............4 Installation ................4 Unpacking the Unit ................. 4 Setup ....................5 Door Panel ..................5 Operation ................7 Turning the Unit On ................ 7 Mode Key ..................7 Technical Specifications ............. -
Page 3: Safety
Safety The following symbols marked on the equipment mean: Caution: Read these operating instructions fully before use and pay particular attention to sections containing this symbol. Attention: Suivre attentivement les instructions avant l’usage et prêtez une attention particulière aux sections comportant ce symbole. -
Page 4: Intended Use Of Product
Intended Use of Product The Boekel Scientific Digital Oven is designed for use where the preparation or testing of materials is done at approximately atmospheric pressure and no flammable, volatile or combustible materials are being heated. All chemicals intended to be treated/prepared must be in sealed, heat-resistant containers. -
Page 5: Setup
during the lift to keep a stable posture. Wearing overtight clothing or unsuitable footwear may make this difficult. • Ensure a good hold on the load. Where possible, hug the load as close as possible to your body. This may be better than gripping it tightly with just your hands. - Page 6 SHELF BRACKET SHELF Control Panel Overview A. Mode Key – Toggles between temperature set-point adjustment mode and timer adjustment mode. B. Start/Stop/Reset – Starts, stops, and resets the timer. Single press of the button will start, stop, or resume the timer. Pressing and holding until an audible tone is heard will reset the timer to the last entered setting.
-
Page 7: Operation
Operation Turning the Unit On 5.1.1 Using the power cord provided with the unit, connect the female end directly into AC socket on rear of unit. Make sure the power switch on rear of unit is off (0). Connect male end of power cord to grounded electrical outlet. - Page 8 LCD display by showing the Actual Temperature on the top line and the Timer value on the bottom line. The Timer colon (:) will be flashing which indicates that the Timer value is adjustable. 5.3 Setting Temperature 5.3.1 Press the Mode Key to enter Temperature mode as indicated in step 5.2.1.
- Page 9 5.5 Over-Temperature Alarm 5.5.1 The unit is equipped with an Over-Temperature Alarm that is activated when the chamber temperature exceeds the Temperature Set Point by more than 5.0°C. When an alarm occurs, the display will alternate between “High Temp Alarm” and the actual chamber temperature.
- Page 10 Subtract the LCD display Actual Temperature from the reference thermometer temperature reading and use this value as the zero adjust. Once zero adjust is determined, use Up/Down arrow key to enter this value. If the zero adjust value is negative, use the Down arrow key, if it is positive use the Up arrow key.
-
Page 11: Technical Specifications
5°C to 30°C, with maximum relative humidity of 80% non-condensing. For operation at altitudes of up to 6500 feet (2000 meters). Degree of Ingress Protection IPX0. Pollution degree 2 in accordance with IEC 664. Overvoltage category II. 151050 151050-2 151140 151140-2 151250... -
Page 12: Fault Diagnosis
Maintenance and Service All Boekel laboratory products are designed to comply with IEC61010-1. No routine maintenance is required. Cleaning Disengage power cord prior to cleaning. Both the inner chamber and outer housing can be cleaned with a cloth dampened with water and mild soap. -
Page 13: Replacement Of Fuses
Boekel warrants this product to be free of defective material and workmanship for a period of two years from the date of manufacture. The liability of Boekel for any defective equipment during the warranty period shall be limited to the repair of such equipment or replacement thereof without charge for parts or labor. -
Page 14: Service
11.0 Service It is required to obtain a Returned Material Authorization (RMA) number before any Boekel products are returned for any reason. A Decontamination Certificate must be completed, signed by the user, and returned to Boekel Scientific prior to receiving the RMA number.
Need help?
Do you have a question about the 151050 and is the answer not in the manual?
Questions and answers