IBS LBP10 User Manual

10A Low
Batterie
Protection
Installation
LBP10
+Vcc
green
red
black
Signal output
(low side switch)
appliances
Connection cable
to LBP10:
Batt LED and Load LED display:
Batt LED Load LED Lead-Main Lithium-Main
> 13.5V > 13.5V
> 12.5V > 13.2V
12.0V-12.5V 12.6V-13.2V
< 12.0V < 12.6V
< 11.6V < 12.2V
Deep disch. Deep disch.
Load discon. Load discon.
* For a 24V system, the voltage levels are twice as high
Status LEDs
Button
DIP-Switch
Basic Function Description
The deep discharge protection switches off the appliance when reaching the
set total discharge value (about 11.6V), whereby the
When charging again, or when the battery voltage reaches the upper
switching value (about 12.6V), the load is automatically switched back on,
with the
blue
The load current is displayed with 10 green LEDs, from 1-10A.
too high, all 10 load current LEDs will flash
load of appliance as well. Another function of the LBP10 is the battery voltage
indication by means of the
Load output
stages (see Batt and Load LED display table). The LBP10 is equipped with a
signal output (Open Collector) for early warning before the load is switched
(high side switch)
off.
Connection panel additional functions
Light
Inverter
DIP switch settings:
DC
AC
Radio
DIP Switch
1 measuring method
2 Battery type
3 Application
Computer
4 Runflat emergency FCN
DIP-Switch1:
via the internal resistances. The voltage measurement can be used if the load
Fridge
is only controlled by the voltage.
DIP-Switch2:
DIP-Switch3:
0.2V lower than when the starter battery is set.
DIP-Switch4:
below the deep discharge value until the runflat safety off level is reached.
Lead-Aux Lithium-Aux
This can lead to a deep discharge and should only be activated in an
> 13.5V > 13.5V emergency. After activating this DIP switch function, the runflat function must
be started by pressing the button for 10 seconds. Press the button again for
> 12.5V > 12.7V
10 seconds to switch off the runflat function. If the button is pressed for 10
11.8-12.5V 12.0-12.7V
seconds without changing the DIP-Switch4, all LEDs will flash.
< 11.8V < 12.4V
< 11.4V < 12.0V
Deep disch. Deep disch. Button functions
Load discon. Load discon.
Reset function of the shutdown (Load turn off)
After the deep discharge protection has switched the Load off, the appliance
can be switched on again without supplying any charge by pressing the
Load LEDs
button. The
If the battery charge is lower than safety turn off no further reset (further Load
re-activation) with button is possible anymore
connected to a charger immediately. If the battery is Lithium-Type with BMS it
might be the battery electronics turns off before LBP10 safety turn off value, in
this case battery has first to be charged!
Manual load disconnection
If the appliance is no longer to be supplied with power, the button can be used
to disconnect the load manually from the battery (pressing the button for 5
seconds).
Activate / deactivate runflat
After pressing the button for 10 seconds, the runflat function is activated and
the load is fed until runflat safety off. After pressing the button again for 10
seconds the runflat function is deactivated. (If DIP-switch 4 is activated).
Users Manual
Load Led
Load Led going out.
and the LBP10 will turn off the
Batt Led, which displays the voltage in three
Off (default) On
Current sensing (RiCT) voltage sensing
Lead Battery Lithium Ion Battery
Starter Battery Bord Battery (AUX)
Disabled Enabled
The RiCT measurement accurately measures the cut-off value
Selection of lead or lithium type battery.
With the AUX (bord battery) setting, the cut-off value is approx.
The runflat function keeps the load in emergency powered on
appliance is fed until the depth discharge value is reached again.
, the battery should be
lights up red.
If the load is