Summary of Contents for Cherry DEVKIT ADDON CAM-TS-A01
- Page 1 DEVKIT ADDON CAM-TS-A01 Haikou-Video-Demo for the HAIKOU CB-MINI-ITX featuring a 5" 720p MIPI-DSI touchscreen and 5 MP MIPI-CSI camera USER MANUAL Document revision: v1.3.0 Issue date: Apr 03, 2024...
-
Page 3: Table Of Contents
Known issues ..........3 Contact 4 Revision History DEVKIT ADDON CAM-TS-A01 User Manual v1.3.0 © Cherry Embedded Solutions GmbH... -
Page 4: Introduction
The camera has a 1/5-inch, 5 megapixel (2592x1944) at 30 fps in 10-bit resolution sensor. Fig. 1.1: Complete setup Note: In favor of readability in this document DEVKIT ADDON CAM-TS-A01 will be referenced by its code name Haikou Video Demo and the HAIKOU CB-MINI-ITX as Haikou carrier board. -
Page 5: Mounting Instructions
3. 3 x hexagonal M3 metal standoffs, 4.5cm each (Wurth 971450471 or similar) 4. 6 x M3x5mm screws 5. 4 x M3 nut 1.2 Mounting Instructions Step 1: Lay the pre-assembled Haikou Video Demo jig with display and camera face-down on a flat surface as shown below: Fig. - Page 6 Fig. 1.4: Mounting Haikou Video Demo PCB to the display jig Step 4: Screw two M3 screws through the PCB into the nuts in the jig. The board is now secured. DEVKIT ADDON CAM-TS-A01 User Manual v1.3.0 © Cherry Embedded Solutions GmbH...
- Page 7 Fig. 1.5: Screwing Haikou Video Demo PCB to the display jig v1.3.0 Page 4...
- Page 8 Step 6: Mount the three hexagonal metal standoffs to the display jig. The display jig has three M3 threads sticking out. Screw the standoffs onto the threads with the M3 screws. Fig. 1.7: Mounting three hexagonal metal standoffs DEVKIT ADDON CAM-TS-A01 User Manual v1.3.0 © Cherry Embedded Solutions GmbH...
- Page 9 Fig. 1.8: Screwing standoffs to the jig Step 7: Flip the display assembly face-up and hover it above the Haikou carrier board. Plug the Haikou Video Demo adapter PCB into the slot marked “Video connector” on the Haikou Development Kit. Slide the threads of the three metal standoffs into the mounting holes of the Haikou carrier board.
- Page 10 Fig. 1.10: M3 nuts that serve as feet for the Haikou carrier board Step 9: Flip the setup around again. The result should look as seen in the photo. Fig. 1.11: Complete setup DEVKIT ADDON CAM-TS-A01 User Manual v1.3.0 © Cherry Embedded Solutions GmbH...
-
Page 11: Ringneck Som-Px30-Uq7 Kernel Configuration
1.3 RINGNECK SOM-PX30-uQ7 Kernel Configuration To enable display output to the Haikou Video Demo board, the correct Device Tree file must be used by Linux. The used file can be configured through the file /boot/extlinux/extlinux.conf. For the RINGNECK SOM-PX30-uQ7 module, open the file with an editor (for example, nano): nano /boot/extlinux/extlinux.conf Replace the line: FDT /boot/px30-ringneck-haikou.dtb... -
Page 12: Camera
INFO Camera camera_manager.cpp:299 libcamera v0.0.4 Available cameras: 1: Internal front camera (/base/i2c@ff110000/camera@36) For more details about libcamera dependencies and build process, you can visit libcamera Getting Started webpage. DEVKIT ADDON CAM-TS-A01 User Manual v1.3.0 © Cherry Embedded Solutions GmbH Page 9... -
Page 13: Camera Examples Using Gstreamer
2.2 Camera examples using GStreamer Libcamera provides a GStreamer plugin (libcamerasrc) that can be used as a video source in the GStreamer pipeline. 2.2.1 Camera preview on display The following command can be used to show a camera preview on the Haikou-Video-Demo display: gst-launch-1.0 libcamerasrc ! video/x-raw, colorimetry=bt709, format=NV12, width=960, height=720, framerate=29/1 ! queue max-size-buffers=16... -
Page 14: Known Issues
2. Auto-focus support is currently missing in the libcamera, but there are works in progress to in- clude it. Patch series with auto-focus support: https://lists.libcamera.org/pipermail/libcamera-devel/ 2023-March/037250.html. DEVKIT ADDON CAM-TS-A01 User Manual v1.3.0 © Cherry Embedded Solutions GmbH Page 11... -
Page 15: Contact
3 Contact Cherry Embedded Solutions GmbH Seestadtstraße 27 1220 Vienna Austria Inquiries: sales-es@cherry.de Technical Support: support-es@cherry.de v1.3.0 Page 12... -
Page 16: Revision History
Feb 16, 2024 v1.1.2 add contact information Mar 01, 2024 v1.2.0 rename to new product name DEVKIT ADDON CAM-TS-A01 change document type from appnote to user manual Apr 02, 2024 v1.3.0 Theobroma Systems is now CHERRY Embedded Systems DEVKIT ADDON CAM-TS-A01 User Manual v1.3.0...
Need help?
Do you have a question about the DEVKIT ADDON CAM-TS-A01 and is the answer not in the manual?
Questions and answers